2011 INFINITI QX56 relay

WIPER AND WASHER FUSEWW-35
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
DTC/CIRCUIT DIAGNOSIS
WIPER AND WASHER FUSE
Diagnosis ProcedureINFOID:0000000006300467
1.CHECK FUSES
Check that the following fuses is not fusing.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace the fuse with a new one after repairing the applicable circuit.
Unit Location No. Capacity
Front wiper motor IPDM E/R 45 30 A
Headlamp washer relay - U 30 A
Washer pump Fuse block (J/B) 1 10 A
Revision: 2010 May2011 QX56

WW-46
< DTC/CIRCUIT DIAGNOSIS >
HEADLAMP WASHER RELAY
HEADLAMP WASHER RELAY
Component InspectionINFOID:0000000006371494
1.CHECK HEADLAMP WASHER RELAY
1. Turn the ignition switch OFF.
2. Remove headlamp washer relay.
3. Apply battery voltage to headlamp washer relay between terminals 1 and 2.
4. Check continuity of headlamp washer relay.
Does continuity exist?
YES >> Headlamp washer relay is normal.
NO >> Replace headlamp washer relay.
Headlamp washer relay Condition Continuity
Terminal Voltage
35 Apply Existed
Not Apply Not existed
Revision: 2010 May2011 QX56

HEADLAMP WASHER CIRCUITWW-47
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
HEADLAMP WASHER CIRCUIT
Component Function CheckINFOID:0000000006371495
1.CHECK HEADLAMP WASHER OPERATION
CONSULT-III ACTIVE TEST
1. Select “HEAD LAMP WASHER” of IPDM E/R active test item.
2. With operating the test item, check headlamp operation.
Is headlamp washer operation normally?
YES >> Headlamp washer circuit is normal.
NO >> Refer to WW-47, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006371496
1.CHECK HEADLAMP WASHER FUSIBLE LINK
1. Turn the ignition switch OFF.
2. Check that the headlamp washer 30A fusible link (#U) is not fusing.
Is the fusible link fusing?
YES >> Replace the fusible link after repairing the applicable circuit.
NO >> GO TO 2.
2.CHECK HEADLAMP WASHER RELAY POWER SUPPLY
1. Remove headlamp washer relay.
2. Check voltage between headlamp washer relay harness connector and ground.
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harnesses or connectors.
3.CHECK HEADLAMP WASHER RELAY
Check headlamp washer relay. Refer to WW-46, "
Component Inspection".
Is the headlamp washer relay normal?
YES >> GO TO 4.
NO >> Replace headlamp washer relay.
4.CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL
CONSULT-III ACTIVE TEST
1. Turn the ignition switch OFF.
2. Install headlamp washer relay.
3. Turn the ignition switch ON.
4. Select “HEAD LAMP WASHER” of IPDM E/R active test item.
5. With operating the test item, check vo ltage between IPDM E/R harness connector and ground.
On :Headlamp washer ON operation
Off :Stop the headlamp washer.
(+)
(− ) Voltage (Approx.)
Headlamp washer relay
Connector Terminal
E51 1
Ground Battery voltage
3
(+)
(− ) Te s t i t e m
Voltage (Approx.)
IPDM E/R
HEAD LAMP WASHER
Connector Terminal
Revision: 2010 May2011 QX56

WW-48
< DTC/CIRCUIT DIAGNOSIS >
HEADLAMP WASHER CIRCUIT
Is the measurement value normal?
YES >> GO TO 7.
Fixed at 0 V >> GO TO 5.
Fixed at battery voltage >>Replace IPDM E/R.
5.CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Remove headlamp washer relay.
3. Disconnect IPDM E/R harness connector.
4. Check continuity between IPDM E/R harness c onnector and headlamp washer relay harness connector.
Does continuity exist?
YES >> GO TO 6.
NO >> Repair the harnesses or connectors.
6.CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL SHORT CIRCUIT
Check continuity between IPDM E/R harness connector and ground.
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> Replace IPDM E/R.
7.CHECK HEADLAMP WASHER PUMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Remove headlamp washer relay.
3. Disconnect headlamp washer pump connector.
4. Check continuity between headlamp washer re lay harness connector and headlamp washer pump har-
ness connector.
Does continuity exist?
YES >> GO TO 8.
NO >> Repair the harnesses or connectors.
8.CHECK HEADLAMP WASHER PUMP (GND) OPEN CIRCUIT
Check continuity headlamp washer pump harness connector and ground.
Does continuity exist?
YES >> Replace headlamp washer pump.
NO >> Repair the harnesses or connectors.
E12 21 Ground On 0 V
Off Battery voltage
IPDM E/R Headlamp washer relay Continuity
Connector Terminal Connector Terminal
E12 21 E51 2 Existed
IPDM E/R GroundContinuity
Connector Terminal
E12 21 Not existed
Headlamp washer relay Headlamp washer pump Continuity
Connector Terminal Connector Terminal
E51 5 E41 1 Existed
Headlamp washer pump GroundContinuity
Connector Terminal
E41 2 Existed
Revision: 2010 May2011 QX56

WIPER AND WASHER SYSTEM SYMPTOMSWW-51
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
Rear wiper does not
stop ON only
 Combination switch
BCM Rear wiper motor circuit
Refer to
WW-43, "
Compo-
nent Function Check".
INT only  Combination switch
BCM Combination switch
Refer to
BCS-80, "
Symptom
Ta b l e"
Rear wiper does not
operate normally Wiper is not linked to
the washer operation.
 Combination switch
 Harness between rear wiper motor and BCM
BCM
Combination switch
Refer to
BCS-80, "
Symptom
Ta b l e"
BCM —
Rear wiper does not
return to the stop posi-
tion. [Stops after a five-
second operation.
(Fail-safe)] BCM
 Harness between rear wiper motor and BCM
 Rear wiper motor
Rear wiper auto stop signal
circuit
Refer to
WW-45, "
Compo-
nent Function Check"
Rear wiper does not
operate even when
shift lever is shifted to
the “R”. Check the linked with reverse rear wiper setting.
Refer to
WW-15, "WIPER : CONSULT-III Function (BCM - WIPER)".
NOTE:
Factory setting of the rear wiper operation is operation linked with reverse.
Shift position signal (CAN communication)
BCM
TCM TCM DATA MONITOR
″
SLCT LVR POSI ″
Headlamp washer
does not operate. Headlamp washer
does not operate with
the front washer when
headlamps are turned
ON.  Combination switch
 Harness between combination switch and BCM
BCM
Combination switch
Refer to
BCS-80, "
Symptom
Ta b l e"
 Fusible link
 Harness between fusible link and headlamp
washer relay
 Headlamp washer relay
 Harness between haedlamp washer relay and IPDM E/R
 IPDM E/R
 Harness between haedlamp washer relay and headlamp washer pump
 headlamp washer pump
 Harness between haedlamp washer pump and ground Headlamp washer circuit
Refer to
WW-47, "
Compo-
nent Function Check"
BCM —
Symptom Probable malfunction location Inspection item
Revision: 2010 May2011 QX56

FRONT WIPER DOES NOT OPERATEWW-53
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
FRONT WIPER DO ES NOT OPERATE
DescriptionINFOID:0000000006300484
The front wiper does not operate under any operation conditions.
Diagnosis ProcedureINFOID:0000000006300485
1.CHECK WIPER RELAY OPERATION
CONSULT-III ACTIVE TEST
1. Select “FRONT WIPER” of IPDM E/R active test item.
2. With operating the test item, check front wiper operation.
Is front wiper operation normally?
YES >> GO TO 5.
NO >> GO TO 2.
2.CHECK FRONT WIPER MOTOR FUSE
Check front wiper motor fuse. Refer to WW-35, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace the fuse after repairing the applicable circuit.
3.CHECK FRONT WIPER MOTOR GROUND CIRCUIT
Check front wiper motor ground circuit. Refer to WW-39, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK FRONT WIPER MOTOR INPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect front wiper motor connector.
3. Turn ignition switch ON.
4. Select “FRONT WIPER” of IPDM E/R active test item.
5. With operating the test item, check voltage between front wiper motor harness connector and ground.
Is the inspection result normal?
YES >> Replace front wiper motor.
NO >> Replace IPDM E/R.
5.CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “FR WIP REQ” of IPDM E/R data monitor item.
2. Switch the front wiper switch to HI and LO. Lo : Front wiper LO operation
Hi : Front wiper HI operation
Off : Stop the front wiper.
(+)
(− ) Condition Voltage (Approx.)
Front wiper motor
Connector Terminal
E42 1
Ground FRONT WIPER Lo Battery voltage
Off 0 V
4 Hi Battery voltage
Off 0 V
Revision: 2010 May2011 QX56