2011 INFINITI QX56 ECO mode

BRC-6
< PRECAUTION >[WITH VDC]
PRECAUTIONS
5. When the repair work is completed, re-connect bot
h battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button igniti on switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
Precaution for Procedure without Cowl Top CoverINFOID:0000000006228176
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution for Brake SystemINFOID:0000000006222556
WARNING:
Clean any dust from the front brake and rear brake using a vacuum dust collector. Never blow by com-
pressed air.
 Brake fluid use refer to MA-10, "
Fluids and Lubricants".
 Never reuse drained brake fluid.
 Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off
immediately and wash with water if it gets on a painted surface.
 Always confirm the specified tightening torque when installing the brake pipes.
 After pressing the brake pedal more deeply or harder t han normal driving, such as air bleeding, check each
item of brake pedal. Adjust brake pedal if it is outside the standard value.
 Never use mineral oils such as gasoline or light oil to clean. They may damage rubber parts and cause
improper operation.
 Always loosen the brake tube flar e nut with a flare nut wrench.
 Tighten the brake tube flare nut to the specified torque with a crow-
foot (A) and torque wrench (B).
 Always connect the battery terminal when moving the vehicle.
 Turn the ignition switch OFF and disconnect the ABS actuator and
electric unit (control unit) harness connector or the battery negative
terminal before performing the work.
 Check that no brake fluid leakage is present after replacing the parts.
Precaution for Brak e Control SystemINFOID:0000000006222557
 Slight vibrations are felt on the brake pedal and the operation noises occur, when VDC function, TCS func-
tion, ABS function, EBD function, hill start assist function or brake limited slip differential (BLSD) function
operates. This is not a malfunction because it is caus ed by VDC function, TCS function, ABS function, EBD
function, hill start assist function or brake limited sl ip differential (BLSD) function that is normally operated.
 When starting engine or when starting vehicle just after starting engine, brake pedal may vibrate or motor
operating noise may be heard from engine compartment. This is normal condition.
 Brake stopping distance may become longer than models without ABS function depending on the road con-
ditions, when ABS function is operated on slippery r oad like rough road, gravel road or snowy road.
 When a malfunction is indicated, always collect info rmation from the customer about conditions of occur-
rence, estimate cause and perform operation. Check brake booster operation, brake fluid level and brake
fluid leakage, as well as electrical system.
 The optimum performance is achieved by control for V DC function, TCS function, ABS function, EBD func-
tion, hill start assist function or brake limited slip di fferential (BLSD) function when all of brakes, suspensions
PIIB3706J
JPFIA0001ZZ
Revision: 2010 May2011 QX56

BRC-24
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Rear LH caliper Being returned to reservoir tank through ABS OUT valve, fluid pressure of rear LH caliper is decreased.
Component Parts and Function
*: Models with Advanced Driver Assistance System
CONDITION FOR TURN ON THE WARNING LAMP
ABS Warning Lamp
 Turns ON at the same time as VDC warning lamp
when either ABS function or EBD function is malfunction-
ing.
 Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
Brake Warning Lamp
 Turns ON at the same time as ABS warning lamp and VDC warning lamp when EBD function, motor/accu- mulator assembly or motor system is malfunctioning.
 Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
Component Function
Pump Operates the pump drive according
to signals from ABS actuator and electric unit (control unit) by
the motor.
Motor Operates the motor driv e according to signals from ABS actuator and electric unit (control unit).
Accumulator The accumulator accumulates brake fluid conveyed by the motor and pump.
ABS IN valve Increases, holds or decreases the fluid pressure of each caliper according to signals from ABS ac-
tuator and electric unit (control unit).
ABS OUT valve Increases, holds or decreases the fluid pressure of each caliper according to signals from ABS ac-
tuator and electric unit (control unit).
Cut valve 1
Cut valve 2 Shuts off the ordinary brake line fr
om master cylinder to signals from ABS actuator and electric unit
(control unit).
Suction valve 1 Suction Valve 1 switches the brake line to convey accumulator pressure to the front system, accord-
ing to a signal transmitted from the ABS ac
tuator and electric unit (control unit).
Suction valve 2 Suction valve 2 releases
accumulator pressure, acco rding to a signal transmitted from the ABS ac-
tuator and electric unit (control unit).
Control pressure sensor
*Detects the brake fluid pressure of rear brake caliper and transmits a signal to ABS actuator and
electric unit (control unit).
Accumulator pressure sensor The accumulator pressure sensor detects brake fluid pressure accumulated in the accumulator and
conveys the detected result to the ABS actuator and electric unit (control unit).
Master cylinder pressure sensor Detects the brake fluid pressure of master cylinder part and transmits a signal to ABS actuator and
electric unit (control unit).
Condition (status) ABS warning lamp
Ignition switch OFF OFF
For approx. 1 seconds after the ignition switch is turned ON ON
Approx. 1 seconds after ignition switch is turned ON (when the
system is in normal operation) OFF
ABS function is ma lfunctioning ON
EBD function is malfunctioning ON
Condition (status) Brake warning lamp
Ignition switch OFF OFF
For approx. 1 seconds after the ignition switch is turned ON ON
Approx. 1 seconds after ignition switch is turned ON (when the
system is in normal operation) OFF
After engine starts OFF
When parking brake operates (parking brake switch ON) ON
Revision: 2010 May2011 QX56

SYSTEMBRC-25
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
VDC Warning Lamp
 Turns ON when either VDC function,
TCS function, ABS function or EBD function, hill start assist function or
brake limited slip differential (BLSD) function is malfunctioning.
 Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
CONDITION FOR TURN ON THE INDICATOR LAMP
VDC OFF Indicator Lamp
 Turns ON when VDC function and TCS function are s witched to non-operational status (OFF) by VDC OFF
switch.
 Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
*: Models with 4WD system
Fail-safeINFOID:0000000006228184
VDC FUNCTION, TCS FUNCTION, hill start assi st FUNCTION AND BRAKE LIMITED SLIP DIFFER-
ENTIAL (BLSD) FUNCTION
VDC warning lamp in combination meter turn ON w hen a malfunction occurs in system [ABS actuator and
electric unit (control unit)]. The control is suspended for VDC function, TCS function, hill start assist function
and brake limited slip differential (BLSD) function. T he Vehicle status becomes the same as models without
VDC function, TCS function, hill star t assist function and brake limited slip differential (BLSD) function. How-
ever, ABS function and EBD f unction are operated normally.
When brake fluid is less than the specified level (brake fluid level
switch ON) ON
ABS function is malfunctioning OFF
EBD function is malfunctioning ON
Accumulator is low pressure ON
Motor system is malfunctioning ON
Ignition power supply system is malfunctioning ON Condition (status) Brake warning lamp
Condition (status) VDC warning lamp
Ignition switch OFF OFF
For approx. 1 seconds after the ignition switch is turned ON ON
Approx. 1 seconds after ignition switch is turned ON (when the
system is in normal operation) OFF
VDC function is malfunctioning ON
TCS function is malfunctioning ON
ABS function is malfunctioning ON
EBD function is malfunctioning ON
hill start assist function is malfunctioning ON
Brake limited slip differential (BLSD) function is malfunctioning ON
VDC function is operating Blinking
TCS function is operating Blinking
Condition (status) VDC OFF indicator lamp
Ignition switch OFF OFF
For approx. 1 seconds after the ignition switch is turned ON ON
Approx. 1 seconds after ignition switch is turned ON (when the
system is in normal operation) OFF
When VDC OFF switch is ON (VDC function and TCS function are
OFF) ON
4WD mode: 4L
*ON
Revision: 2010 May2011 QX56

BRC-26
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
ABS FUNCTION
ABS warning lamp and VDC warning lamp in combinati
on meter turn ON when a malfunction occurs in system
[ABS actuator and electric unit (control unit)]. The c ontrol is suspended for VDC function, TCS function, ABS
function, hill start assist function and brake limited sl ip differential (BLSD) function. The vehicle status
becomes the same as models without VDC function, TCS f unction, ABS function, hill start assist function and
brake limited slip differential (BLSD) function. However, EBD function is operated normally.
NOTE:
ABS self-diagnosis sound may be heard the same as in the normal condition, because self-diagnosis is per-
formed when ignition switch turns ON and when vehicle initially starts.
EBD FUNCTION
ABS warning lamp, brake warning lamp and VDC warning lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC
function, TCS function, ABS function, EBD function, hill start assist function and brake limited slip differential
(BLSD) function. The vehicle status becomes the sa me as models without VDC function, TCS function, ABS
function, EBD function, hill star t assist function and brake limited slip differential (BLSD) function.
DTC Malfunction detected condition Fail-safe condition
C1101 When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function (only when both 2 rear wheels are malfunctioning)
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1102 When an open circuit is detected in rear LH wheel sensor circuit.
C1103 When an open circuit is detected in front RH wheel sensor circuit.
C1104 When an open circuit is detected in front LH wheel sensor circuit.
C1105
 When power supply voltage of rear RH wheel sensor is low.
 When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
 When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not
normal.
C1106  When power supply voltage of rear LH wheel sensor is low.
 When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
 When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor- mal.
C1107  When power supply voltage of front RH wheel sensor is low.
 When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
 When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
C1108  When power supply voltage of front LH wheel sensor is low.
 When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
 When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
C1109  When ignition voltage is 10 V or less.
 When ignition voltage is 16 V or more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 1111
 When a malfunction is detected in motor or motor relay.
 When a low pressure malfunction is detected in accumulator.
 When a malfunction is detected in accumulator pressure sensor.
C 111 5 When difference in wheel speed between any wheel and others is detected during
the vehicle is driven, because of installation of other tires than specified. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 111 6
 When stop lamp switch signal is not input when brake pedal depress.
 When stop lamp switch signal is not input when stop lamp relay operates.
C 111 8
*1When a malfunction is detected in transfer control unit system.
Revision: 2010 May2011 QX56

BRC-28
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
*1: Models with 4WD System
*2: Models with Advanced Driver Assistance System
Protection FunctionINFOID:0000000006228185
The VDC warning lamp, ABS warning lamp and brake warning lamp turns ON and DTC “C118E” may be
detected in self-diagnosis result of “ABS” when the br
ake pedal is excessively operated, such as air bleeding.
This is not a system malfunction because this occurs due to the temporary decrease in accumulator fluid pres-
sure. The system returns to normal condition when the accu mulator fluid pressure reaches the specified pres-
sure with the ignition switch ON and the VDC warning lamp, ABS warning lamp, and brake warning lamp turn
OFF. After these steps, erase self-diagnos is results for “ABS” with CONSULT-III.
NOTE:
D T C “ C 1111 ” i s d e t e c t e d i n s e l f - d i agnosis results of “ABS” when the a ccumulator system has a malfunction.
VDC FUNCTION
VDC FUNCTION : System DescriptionINFOID:0000000006222572
 Side slip or tail slip may occur while driving on a slippery road or intending an urgent evasive driving. VDC
function detects side slip status using each sensor when side slip or tail slip is about to occur and improves
vehicle stability by brake control and engine output control during driving.
 In addition to ABS function, EBD function and TCS functi on, target side slip amount is calculated according
to steering operation amount from steering angle sensor and brake operation amount from pressure sensor.
By comparing this information with vehicle side slip amount that is calculated from information from yaw rate/
C118EWhen performing excessive brake pedal operation with the vehicle stopped. [When
accumulator fluid pressure reaches 11.43 MPa (114 bar, 116.6 kg/cm2, 1657 psi) af-
ter reaching 17.3 MPa (173 bar, 176.5 kg/cm2, 2509 psi.] The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
U1000 When CAN communication signal is not continuously received for 2 seconds or
more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
DTC Malfunction detected condition Fail-safe condition
DTC
 VDC warning lamp
 ABS warning lamp
 Brake warning lamp
Condition Description protection function
C118E ON When temporary decrease in accumulator fluid pres-
sure.
NOTE:
System is not malfunction. The following functions are suspended
temporarily
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD)
function
Revision: 2010 May2011 QX56

SYSTEMBRC-29
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
side/decel G- sensor and wheel sensor, vehicle drivi ng conditions (conditions of understeer or oversteer) are
judged and vehicle stability is improved by brake forc e control on all 4 wheels and engine output control.
 Control unit portion automatically improves driving st ability by performing brake force control as well as
engine output control, by transmitting drive signal to actuator portion according to difference between target
side slip amount and vehicle side slip amount
 VDC function can be switched to non-operational status (OFF) by operating VDC OFF switch. In this case,
VDC OFF indicator lamp turns ON.
 VDC function is not operate when 4WD mode is “4L”. (Models with 4WD system)
 VDC warning lamp blinking while VDC function is in oper ation and indicates to the driver that the function is
in operation.
 Slight vibrations are felt on the brake pedal and t he operation noises occur, when VDC function operates.
This is not a malfunction because it is caus ed by VDC function that is normally operated.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. When a malfunction occurs in VDC function, the control is suspended for VDC
function, TCS function, hill start as sist function and brake limited slip di fferential (BLSD) function. The vehi-
cle status becomes the same as m odels without VDC function, TCS functi on, hill start assist function and
brake limited slip differential (BLSD) function. Ho wever, ABS function and EBD function are operated nor-
mally. Refer to BRC-25, "
Fail-safe".
NOTE:
VDC has the characteristic as de scribed here, but it is not the device that helps reckless driving.
SYSTEM DIAGRAM
NOTE:
Transfer control unit is applied to models with 4WD system.
INPUT SIGNAL AND OUTPUT SIGNAL
JPFIC0133GB
JPFIC0183GB
Revision: 2010 May2011 QX56

SYSTEMBRC-31
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
 During a cornering, brake force (brake fluid pressu re) is applied on front wheel and rear wheel on the inner
side of turn. Moment directing towards the inner side of turn is generated. Understeer is prevented.
 Applying braking during a cornering on a slippery road, when understeer tendency is judged large, engine
output is controlled as well as brake force (brake fluid pressure) of four wheels. Understeer tendency
decreases.
TCS FUNCTION
TCS FUNCTION : System DescriptionINFOID:0000000006222573
 Wheel spin status of drive wheel is detected by wheel sensor of 4
wheels. Engine output and transmission shift status is controlled
so that slip rate of drive wheels is in appropriate level. When wheel
spin occurs on drive wheel, ABS ac tuator and electric unit (control
unit) perform brake force control of LH and RH drive wheels (apply
brake force by increasing brake fluid pressure of drive wheel) and
decrease engine torque by engine torque control. Wheel spin
amount decreases. Engine torque is controlled to appropriate
level.
 TCS function can be switched to non-operational status (OFF) by
operating VDC OFF switch. In this case, VDC OFF indicator lamp
turns ON.
 TCS function is not operate when 4WD mode is “4L”. (Models with
4WD system)
 VDC warning lamp blinking while TCS function is in operation and indicates to the driver that the function is in operation.
 Slight vibrations are felt on the brake pedal and the operation noises occur, when TCS function operates. This is not a malfunc-
tion because it is caused by TCS function that is normally oper-
ated.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. W hen a malfunction occurs in TCS
function, the control is suspended for VDC function, TCS function,
hill start assist function and brake limited slip differential (BLSD)
function. The vehicle status becomes the same as models without VDC function, TCS function, hill start
assist function and brake limited slip differential (B LSD) function. However, ABS function and EBD function
are operated normally. Refer to BRC-25, "
Fail-safe".
SYSTEM DIAGRAM
NOTE:
JPFIC0137GB
JPFIC0138GB
JPFIC0139GB
Revision: 2010 May2011 QX56

SYSTEMBRC-33
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
ABS FUNCTION : System DescriptionINFOID:0000000006222574
 By preventing wheel lock through brake force (brake flui d pressure) control that is electronically controlled by
detecting wheel speed during braking, stability during em ergency braking is improved so that obstacles can
be easily bypassed by steering operation.
 During braking, control units calculates wheel speed and pseudo-vehicle speed, and transmits pressure
increase, hold or decrease signals to actuator portion according to wheel slip status.
 The following effects are obtained by preventing wheel lock during
braking.
- Vehicle tail slip is prevented during braking when driving straight.
- Understeer and oversteer tendencie s are moderated during brak-
ing driving on a corner.
- Obstacles may be easily bypassed by steering operation during braking.
 Slight vibrations are felt on the brake pedal and the operation noises occur, when ABS function oper ates. This is not a malfunc-
tion because it is caused by ABS function that is normally oper-
ated.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. When a malfunction occurs in ABS function, the control is suspended for VDC function, TCS function,
hill start assist function and brake limited slip differential (BLSD)
function. The vehicle status becomes the same as models without
VDC function, TCS function, ABS func tion, hill start assist function
and brake limited slip differential (BLSD) function. However, EBD
function is operated normally. Refer to BRC-25, "
Fail-safe".
NOTE:
 ABS has the characteristic as described here, but it is not the device that helps reckless driving.
 To stop vehicle efficiently, ABS does not operate and ordinary brake operates at low speed [approx. 5 to 10 km/h (3.1 to 6.2
MPH) or less, but differs subject to road conditions).
 Self-diagnosis is performed immediately after when engine starts and when vehicle initially is driven [by vehi-
cle speed approx. 15 km/h (9.3 MPH)]. Motor sounds are generated during self-diagnosis. In addition, brake
pedal may be felt heavy when depressing brake pedal lightly. These symptoms are not malfunctions.
SYSTEM DIAGRAM
NOTE:
JPFIC0140GB
Revision: 2010 May2011 QX56