2011 INFINITI QX56 ABS

DLN-24
< ECU DIAGNOSIS INFORMATION >[TRANSFER: ATX90A]
TRANSFER CONTROL UNIT
ECU DIAGNOSIS INFORMATION
TRANSFER CONTROL UNIT
Reference ValueINFOID:0000000006222227
VALUES ON THE DIAGNOSIS TOOL
Monitor item Condition Value/Status
4WD MODE IGN ON 4WD is booting BOTNG
4WD mode is switching SWTNG
4WD mode: 4L 4L
4WD mode: 4H 4H
4WD mode: AUTO AUTO
2WD SWITCH
*1Always OFF
AUTO SWITCH 4WD shift switch: AUTO ON
4WD shift switch: 4H or 4L OFF
4H SWITCH 4WD shift switch: 4H ON
4WD shift switch: AUTO or 4L OFF
4L SWITCH 4WD shift switch: 4L ON
4WD shift switch: AUTO or 4H OFF
T/M RANGE A/T shift selector: D D
A/T shift selector: N N
A/T shift selector: R R
A/T shift selector: P P
N RANGE SW A/T shift selector: N ON
A/T shift selector: Except N OFF
R RANGE SW A/T shift selector: R ON
A/T shift selector: Except R OFF
IGN SW IGN SW: ON ON
IGN SW: OFF OFF
TCS OPER SW TCS is operating ON
TCS is not operating OFF
VDC OPER SW VDC is operating ON
VDC is not operating OFF
ABS OPER SW ABS is operating ON
ABS is not operating OFF
SAND MODE IND
*2Always OFF
ROCK MODE IND
*2Always OFF
SNOW MODE IND
*2Always OFF
ONROAD MODE IND
*2Always ON
SAND MODE SW
*3Always OFF
ROCK MODE SW
*3Always OFF
SNOW MODE SW
*3Always OFF
ONROAD MODE SW
*3Always ON
Revision: 2010 May2011 QX56

TRANSFER CONTROL UNITDLN-29
< ECU DIAGNOSIS INFORMATION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
DTC Inspection Priority ChartINFOID:0000000006222229
If some DTCs are displayed at the same time, per form inspections one by one based on the following priority
chart.
DTC IndexINFOID:0000000006222230
Priority Detected items (DTC)
1  U1000 CAN COMM CIRCUIT
 U1010 CONTROL UNIT (CAN)
2  P1802 CONTROL UNIT 1
 P1803 CONTROL UNIT 2
 P1804 CONTROL UNIT 3
 P1809 CONTROL UNIT 4
 P180C SEN POWER SUPPLY (5V)
 P180E SEN POWER SUPPLY (8V)
 P1811 BATTERY VOLTAGE
 P181B INCOMP SELFSHUT
 P181C MOTOR POWER SUPPLY
 P181F INCOMP CALIBRATION
3  P1807 VECL SPEED SEN-AT
 P1808 VECL SPEED SEN-ABS
 P1816 PNP SW/CIRC
 P181E ST ANGLE SEN SIG
 P1820 ENGINE SPEED SIG
 P1829 THROTTLE POSI SEN
 P1830 ABS OP SIG
 P1831 VDC OP SIG
 P1832 TCS OP SIG
4  P180D ROTARY POSITION SEN
 P1813 4WD MODE SW
 P181A MOTOR TEMP SEN
 P1826 OIL TEMP SEN
 P182A HI-LO POSITION SEN
 P182B LOCK POSITION SEN
5  P180F MOTOR SYSTEM
 P1817 SHIFT ACTUATOR
DTC Display Items Reference
P1802 CONTROL UNIT 1 DLN-51, "
DTC Logic"
P1803 CONTROL UNIT 2DLN-51, "DTC Logic"
P1804 CONTROL UNIT 3DLN-51, "DTC Logic"
P1807 VHCL SPEED SEN-ATDLN-52, "DTC Logic"
P1808 VHCL SPEED SEN-ABSDLN-53, "DTC Logic"
P1809 CONTROL UNIT 4DLN-51, "DTC Logic"
P180C SEN POWER SUPPLY (5V) DLN-54, "DTC Logic"
P180D ROTARY POSITION SENDLN-57, "DTC Logic"
P180E SEN POWER SUPPLY (8V)DLN-59, "DTC Logic"
P180F MOTOR SYSTEMDLN-61, "DTC Logic"
P1811 BATTERY VOLTAGEDLN-64, "DTC Logic"
P1813 4WD MODE SW DLN-67, "DTC Logic"
P1816 PNP SW/CIRCDLN-69, "DTC Logic"
P1817 SHIFT ACTUATORDLN-70, "DTC Logic"
P181A MOTOR TEMP SEN DLN-72, "DTC Logic"
P181B IMCOMP SELFSHUTDLN-74, "DTC Logic"
Revision: 2010 May2011 QX56

DLN-30
< ECU DIAGNOSIS INFORMATION >[TRANSFER: ATX90A]
TRANSFER CONTROL UNIT
P181C MOTOR POWER SUPPLY
DLN-76, "DTC Logic"
P181E ST ANGLE SEN SIGDLN-77, "DTC Logic"
P181F INCOMP CALIBRATIONDLN-78, "DTC Logic"
P1826 OIL TEMP SENDLN-80, "DTC Logic"
P1820 ENGINE SPEED SIGDLN-79, "DTC Logic"
P1829 THROTTLE POSI SENDLN-82, "DTC Logic"
P182A HI-LO POSITION SEN DLN-83, "DTC Logic"
P182B LOCK POSITION SENDLN-85, "DTC Logic"
P1830 ABS OP SIGDLN-88, "DTC Logic"
P1831 VDC OP SIGDLN-89, "DTC Logic"
P1832 TCS OP SIGDLN-90, "DTC Logic"
U1000 CAN COMM CIRCUIT DLN-91, "DTC Logic"
U1010 CONTROL UNIT (CAN)DLN-92, "DTC Logic"
DTC Display Items Reference
Revision: 2010 May2011 QX56

P1808 WHEEL SPEED SENSORDLN-53
< DTC/CIRCUIT DIAGNOSIS > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
P1808 WHEEL SPEED SENSOR
DTC LogicINFOID:0000000006222248
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DTC REPRODUCTION PROCEDURE
With CONSULT-III
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1minute.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC
“P1808” detected?
YES >> Proceed to diagnosis procedure. Refer to DLN-53, "DTC Logic".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222249
1.PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES >> Check the DTCs.
NO >> GO TO 2.
2.ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES >> GO TO 3.
NO >> Refer to BRC-122, "
Diagnosis Procedure".
3.CHECK TERMINALS AND HARNESS CONNECTORS
Check transfer control unit pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES >> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
"P1808" is detected, Replace transfer control unit. Refer to DLN-107, "
Removal and Installation".
NO >> Repair or replace error-detected parts.
DTC Display item Malfunction detected condition Possible cause
P1808 VHCL SPEED SEN-ABS  Malfunction is detected in vehicle
speed signal that is output from ABS
actuator and electric unit (control unit)
through CAN communication.
 Improper signal is input while driving.  Harness or connector (CAN communi-
cation line)
 Malfunction of ABS actuator and elec-
tric unit (control unit)
- Malfunction of ABS actuator and elec-
tric unit (control unit) circuit error
- Vehicle speed signal error
Revision: 2010 May2011 QX56

P181E STEERING ANGLE SENSORDLN-77
< DTC/CIRCUIT DIAGNOSIS > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
P181E STEERING ANGLE SENSOR
DTC LogicINFOID:0000000006222279
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DTC REPRODUCTION PROCEDURE
With CONSULT-III
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC
“P181E” detected?
YES >> Proceed to diagnosis procedure. Refer to DLN-77, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222280
1.PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ABS”.
Is DTC
“C1143” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-97, "Diagnosis Procedure".
NO >> GO TO 2.
2.CHECK CAN COMMUNICATION LINE
Check communication line. Refer to LAN-69, "
Diagnosis Procedure".
Is inspection result normal?
YES >> Replace transfer control unit. Refer to DLN-107, "Removal and Installation".
NO >> Repair or replace error-detected parts.
DTC Display item Malfunction detected condition Possible cause
P181E ST ANGLE SEN SIG Malfunction is detected in steering angle
sensor signal through CAN communica-
tion. Harness or connector (CAN communi-
cation line)
 Steering angle sensor
- Steering angle sensor error
- Malfunction of steering angle sensor circuit error
Revision: 2010 May2011 QX56

DLN-88
< DTC/CIRCUIT DIAGNOSIS >[TRANSFER: ATX90A]
P1830 ABS OPERATION SIGNAL
P1830 ABS OPERATION SIGNAL
DTC LogicINFOID:0000000006222294
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DTC REPRODUCTION PROCEDURE
With CONSULT-III
1. Start the engine and drive at 30 km/h (19 MPH) or more.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC
“P1830” detected?
YES >> Proceed to diagnosis procedure. Refer to DLN-88, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222295
1.PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES >> Check the DTCs.
NO >> GO TO 2.
2.ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES >> GO TO 3.
NO >> Refer to BRC-123, "
Diagnosis Procedure".
3.CHECK TERMINALS AND HARNESS CONNECTORS
Check transfer control unit pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES >> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
"P1830" is detected, Replace transfer control unit. Refer to DLN-107, "
Removal and Installation".
NO >> Repair or replace error-detected parts.
DTC Display item Malfunction detected condition Possible cause
P1830 ABS OP SIG Malfunction is detect
ed in ABS operation
signal that is outp ut from ABS actuator
and electric unit (control unit) through
CAN communication. Malfunction of ABS system
Revision: 2010 May2011 QX56

P1831 VDC OPERATION SIGNALDLN-89
< DTC/CIRCUIT DIAGNOSIS > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
P1831 VDC OPERATION SIGNAL
DTC LogicINFOID:0000000006222296
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DTC REPRODUCTION PROCEDURE
With CONSULT-III
1. Start the engine and drive at 30 km/h (19 MPH) or more.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC
“P1831” detected?
YES >> Proceed to diagnosis procedure. Refer to DLN-89, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222297
1.PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES >> Check the DTCs.
NO >> GO TO 2.
2.ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES >> GO TO 3.
NO >> Refer to BRC-122, "
Diagnosis Procedure".
3.CHECK TERMINALS AND HARNESS CONNECTORS
Check transfer control unit pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES >> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
"P1831" is detected, Replace transfer control unit. Refer to DLN-107, "
Removal and Installation".
NO >> Repair or replace error-detected parts.
DTC Display item Malfunction detected condition Possible cause
P1831 VDC OP SIG Malfunction is detected in VDC opera-
tion signal that is output from ABS actu-
ator and electric unit (control unit)
through CAN communication.Malfunction of ABS system
Revision: 2010 May2011 QX56

DLN-90
< DTC/CIRCUIT DIAGNOSIS >[TRANSFER: ATX90A]
P1832 TCS OPERATION SIGNAL
P1832 TCS OPERATION SIGNAL
DTC LogicINFOID:0000000006222298
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DTC REPRODUCTION PROCEDURE
With CONSULT-III
1. Start the engine and drive at 30 km/h (19 MPH) or more.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC
“P1832” detected?
YES >> Proceed to diagnosis procedure. Refer to DLN-90, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222299
1.PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES >> Check the DTCs.
NO >> GO TO 2.
2.ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES >> GO TO 3.
NO >> Refer to BRC-122, "
Diagnosis Procedure".
3.CHECK TERMINALS AND HARNESS CONNECTORS
Check transfer control unit pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES >> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
"P1832" is detected, Replace transfer control unit. Refer to DLN-107, "
Removal and Installation".
NO >> Repair or replace error-detected parts.
DTC Display item Malfunction detected condition Possible cause
P1832 TCS OP SIG Malfunction is detected in TCS operation
signal that is outp
ut from ABS actuator
and electric unit (control unit) through
CAN communication. Malfunction of TCS system
Revision: 2010 May2011 QX56