2011 INFINITI QX56 belt

SE-112
< REMOVAL AND INSTALLATION >
FRONT SEAT
Removal and Installation
INFOID:0000000006217424
REMOVAL
CAUTION:
 When removing and installing, use shop cloths to protect parts from damage.
 When removing and installing, 2 workers are required so as to prevent it from dropping.
1. Remove the front slide cover.
a. Front outer slide cover  Slide the seat to the rearmost position.
 Pull up the front edge of the front slide cover to release the
pawls.
 Slide the front slide cover forward to release the pawls.
13. Climate controlled seatback blower
motor 14. Climate controlled seatback blower
motor bracket 15. Seatback climate controlled seat
blower filter
16. Seatback thermal electric unit 17. Seat cushion lower outer finisher 18. Seatback climate controlled seat duct finisher
19. Seatback thermal electric unit brack- et 20. Seat cushion lower inner finisher 21. Rear inner slide cover
22. Rear outer slide cover 23. Seat harness 24. Seat cushion outer finisher inside (front)
25. Seat cushion outer finisher inside (rear) 26. Lumber support switch 27. Seat control switch cover
28. Seat control switch 29. Seat cushion outer finisher 30. Seat reclining switch knob
31. Seat slide and lifter switch knob 32. Climate controlled seat control unit 33. Seat cushion climate controlled seat harness
34. Seat cushion climate controlled seat hook (rear) 35. Seat cushion climate controlled seat
bracket 36. Climate controlled seat cushion
blower motor
37. Seat cushion climate controlled seat hook (front) 38. Seat cushion climate controlled seat
duct 39. Seat cushion thermal electric unit
40. Seat cushion climate controlled seat duct finisher 41. Seat cushion climate controlled seat
blower filter 42. Occupant detection system control
unit
43. Front outer slide cover 44. Front inner slide cover 45. Seat cushion front finisher
46. Seat cushion pad 47. Seat cushion trim 48. Seat cushion inner finisher
49. Seat cushion inner finisher inside (front) 50. Seat cushion inner finisher inside
(rear) 51. Anchor bolt
52. Seat belt buckle pre-tensioner 53. Foot welcome lamp 54. Seatback pad
55. Seatback trim 56. Seatback silencer 57. Headrest display harness lower tube
58. Lumber support unit assembly 59. Seat frame assembly : Pawl
: Metal clip
Refer to GI-4, "
Components" for symbols in the figure.
: Pawl
JMJIA3824ZZ
Revision: 2010 May2011 QX56

SE-116
< REMOVAL AND INSTALLATION >
FRONT SEAT
SEAT CUSHION : Disa ssembly and Assembly
INFOID:0000000006217426
DISASSEMBLY
1. Remove the seat cushion outer finisher.
1. Remove the metal clips and pawls, and then pull out seat
cushion outer finisher.
2. Disconnect the seat control switch, lumbar support switch harness connector.
2. Remove the seat cushion front finisher.
3. Remove the lap pre-tensioner. Refer to SB-8, "
SEAT BELT BUCKLE : Removal and Installation".
4. Remove the seat cushion inner finisher. 1. Remove the seat cushion inner finisher fixing screw (A).
2. Remove the metal clip and pawls then pull out seat cushioninner finisher.
5. Disconnect the seat cushion heater unit harness connector (A). (with heater seat model only)
6. Remove the seat cushion trim and seat cushion pad. 1. Remove the seat cushion retainer.
2. Remove the seat cushion trim and seat cu shion pad from the seat frame assembly.
3. Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
7. Remove the seat cushion finisher inside.  Remove the seat cushion inner finisher inside (front, rear).
 Remove the seat cushion outer finisher inside (front, rear).
8. Remove the following parts after removing seat cushion finisher inside.  Seat cushion climate controlled seat unit (with climate controlled seat model only).
Refer to SE-117, "
CLIMATE CONTROLLED SEAT UNIT : Disassembly and Assembly".
 Seat control unit (driver seat only).
Refer to ADP-135, "
Removal and Installation".
 Remove occupant detection system control unit. Refer to SR-30, "
Removal and Installation".
: Pawl
: Metal clip
JMJIA3966ZZ
: Pawl
: Metal clip
JMJIA3977ZZ
: Vehicle front
JMJIA4327ZZ
Revision: 2010 May2011 QX56

SECOND SEATSE-121
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
*: Heater seat model only.
BENCH SEAT (RH SEAT) AND CAPTAIN SEAT (RH SEAT)
1. Headrest LH 2. Headrest (center) 3. Headrest holder (free)
4. Headrest holder (locked) 5. Seatback heater unit
*6. Seatback trim
7. Seatback pad 8. Armrest outer cover 9. Armrest outer bracket
10. Bush 11. Armrest inner cover RH 12. Armrest trim
13. Armrest pad & frame 14. Armrest inner cover LH 15. Cup holder
16. Reclining inner cover (outside) 17. Seat inner hinge 18. Reclining device inner cover (out- side)
19. Reclining device inner cover (inside) 20. Seat cushion heater unit
*21. Seat cushion trim
22. Seat cushion pad 23. Seat hinge cover RH 24. Seat cushion hinge cover RH
25. Seat hinge cover LH 26. Seat cushion hinge cover LH 27. Seat cushion under cover
28. Seat harness assembly 29. Device arm cover 30. Reclining device outer cover (inside)
31. Reclining device outer cover (out- side) 32. Snap ring 33. Reclining lever knob
34. Anchor bolt 35. Seat belt buckle (center) 36. Seat belt buckle LH
37. Center seat belt retractor 38. Screw cap 39. Seatback center finisher
40. Seatback center finisher cover 41. Center seat belt shoulder guide 42. Seatback board
43. Seatback board clip 44. Center seat belt guide 45. Rear seat lever assembly
46. Seat control lever escutcheon 47. Seatback frame 48. Seat cushion frame
49. Seat hinge assembly RH 50. Seat cushion carpet RH 51. Seat hinge assembly LH
52. Seat cushion carpet LH : Pawl
Refer to GI-4, "
Components" for symbols in the figure.
Revision: 2010 May2011 QX56

SE-122
< REMOVAL AND INSTALLATION >
SECOND SEAT
1. Headrest RH 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seatback trim 5. Seatback pad 6. Seat cushion trim
7. Seat cushion pad 8.Seat cushion heater unit
*9. Seat cushion under cover
10. Seat cushion hinge cover RH 11. Seat hinge cover RH 12. Seat cushion hinge cover LH
13. Seat harness assembly 14. Seat cushion carpet 15. Seat belt buckle anchor bolt
16. Seat belt buckle 17. Reclining inner cover (outside) 18. Seatback frame
JMJIA4580GB
Revision: 2010 May2011 QX56

SE-124
< REMOVAL AND INSTALLATION >
SECOND SEAT
1. Headrest 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seatback trim 5. Seatback pad 6. Seat cushion heater unit
7. Seat cushion trim 8. Seat cushion pad 9. Seat cushion under cover
10. Seat hinge assembly RH 11. Seat cushion hinge cover RH 12. Seat hinge cover LH
13. Seat cushion hinge cover LH 14. Seat hinge assembly LH 15. Seat harness assembly
16. Seat cushion carpet 17. Anchor bolt 18. Seat belt buckle
JMJIA4581GB
Revision: 2010 May2011 QX56

SECOND SEATSE-127
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
(heater seat model only)
5. Remove the rear seat lever assembly. 1. Remove the rear seat lever assembly fixing screws.
2. Lift rear seat lever assembly and remove seatback control wire.
6. Remove the seatback center finisher. 1. Pull seatback center finisher cover rearward to remove.
2. Remove the seatback center finisher fixing screws.
3. Remove the seat belt from seatback center finisher.
7. Remove the center seat belt anchor. 1. Remove the seat cushion and seat cushion under cover.
Refer to SE-130, "
SEAT CUSHION : Disassembly and Assembly".
2. Remove the center seat belt anchor. Refer to SB-13, "
SEAT BELT RETRACTOR : Removal and Installation".
8. Remove the seatback trim and seatback pad. 1. Remove the headrest holder. CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
JMJIA4471ZZ
: Pawl
JMJIA3877ZZ
PIIB4084J
Revision: 2010 May2011 QX56

SE-128
< REMOVAL AND INSTALLATION >
SECOND SEAT
2. Roll up seatback trim (2) from backward to forward so thatseat control lever escutcheon (1) is visible.
3. Remove the seat control lever escutcheon (1).
4. Remove the seatback trim and seat back pad from the seatback frame.
5. Remove the hog rings, and separate the seatback trim and seatback pad.
9. Remove the seat belt retractor.
10. Remove the seatback frame. 1. Remove the device arm cover.
2. Remove the reclining device inner cover (outside) and reclining device inner cover (inside).
Refer to SE-130, "
SEAT CUSHION : Disassembly and Assembly".
3. Remove the reclining device outer cover (out side) and reclining device outer cover (inside).
Refer to SE-130, "
SEAT CUSHION : Disassembly and Assembly".
4. Remove the seatback control wire (A) and seat cushion control wire (B).
5. Remove the reclining inner cover (outside).
6. Remove the mounting bolts and then remove seatback frame.
BENCH SEAT (RH SIDE) AND CAPTAIN SEAT
1. Remove the seatback retainers (A), and then open the fasteners (B).
2. Remove the seatback board and the clips.
: Pawl
JMJIA3878ZZ
JMJIA3886ZZ
JMJIA3875ZZ
Revision: 2010 May2011 QX56

SECOND SEATSE-131
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
3. Remove the reclining device outer cover (outside) Pull reclining device outer cover forward and disengage pawls.
4. Remove the fixing screw and then remove seat cushion under cover.
5. Remove the reclining device outer cover (inside).
6. Remove the center seat belt anchor. Refer to SB-13, "
SEAT BELT RETRACTOR : Removal and Installa-
tion".
7. Remove the seatback trim and seatback pad. Refer to SE-126, "
SEATBACK : Disassembly and Assem-
bly".
8. Remove the device arm cover.
9. Remove the reclining device inner cover (outside) (1) and reclin- ing device inner cover (inside) (2).
10. Remove the seat cushion frame. 1. Remove the seatback control wire (A) and seat cushion control wire (B).
2. Remove seatback control wire installed to seat cushion frame.
3. Remove the mounting bolts and then remove seat cushion frame.
11. Remove the seat cushion hinge cover
: Pawl
JMJIA3882ZZ
: Pawl
JMJIA3887ZZ
JMJIA3886ZZ
Revision: 2010 May2011 QX56