2011 INFINITI QX56 display

BRC-42
< SYSTEM DESCRIPTION >[WITH VDC]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
Note 1: Refer to BRC-16, "System Description" for ON/OFF conditions of each warning lamp and indicator
lamp.
Note 2: Models with 4WD System
Note 3: Models with Advanced Driver Assistance System
Note 4: USS means “hill start assist”
ACTIVE TEST
The active test is used to determine and identify details of a malfunction, based on self-diagnosis test result
sand data obtained in the DATA MONITOR. In response to instructions from CONSULT-III, instead of those
SV2
(On/Off) Suction valve 2 operation status is displayed.
STOP LAMP SW2
(On/Off) Stop lamp switch signal input status is displayed.
ACCEL POS SIG
(%) ×
Displays the Accelerator pedal position
SIDE G-SENSOR
(m/s
2) ×
Side G detected by side G sensor is displayed.
STR ANGLE SIG
( ° ) ×
Steering angle detected by steering angle sensor is dis-
played.
PRESS SENSOR
(bar) ×Detects the brake fluid pressure of master cylinder part is
displayed.
ACCUM PRESS SEN
(bar) Detects the brake fluid pressure of accumulator is dis-
played.
CONT PRESS SEN
(Note 3)
(bar) Detects the brake fluid pressure of control pressure sensor
is displayed
EBD SIGNAL
(On/Off) EBD operation status is displayed.
ABS SIGNAL
(On/Off) ABS operation status is displayed.
TCS SIGNAL
(On/Off) TCS operation status is displayed.
VDC SIGNAL
(On/Off) VDC operation status is displayed.
EBD FAIL SIG
(On/Off) EBD fail-safe signal status is displayed.
ABS FAIL SIG
(On/Off) ABS fail-safe signal st
atus is displayed.
TCS FAIL SIG
(On/Off) TCS fail-safe signal status is displayed.
VDC FAIL SIG
(On/Off) VDC fail-safe signal status is displayed.
CRANKING SIG
(On/Off) Cranking status is displayed.
FLUID LEV SW
(On/Off) ×Brake fluid level signal input status via CAN communication
is displayed.
PARK BRAKE SW
(On/Off) ×Parking brake switch signal input status via CAN communi-
cation is displayed.
STP ON RLY
(On/Off) Stop lamp switch relay status is displayed.
USS SIG
(Note 4)
(On/Off) hill start assist operation status is displayed.
Item (Unit)
Monitor item selection
Note
INPUT SIGNALS MAIN ITEMS
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-43
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
from ABS actuator and electric unit (control unit) on the vehi cle, a drive signal is sent to the actuator to check
its operation.
CAUTION:
 Never perform ACTIVE TEST while driving the vehicle.
 Always bleed air from brake system before active test.
 Never perform active test when system is malfunctioning.
NOTE:
 When active test is performed while depressing the pedal, the pedal depressing stroke may change. This is
not a malfunction.
 “TEST IS STOPPED” is displayed approx. 10 seconds after operation start.
 When performing active test again after “TEST IS STOPPED” is displayed, select “BACK”.
 ABS warning lamp, brake warning lamp and VDC warning lamp may turn ON during active test. This is not a malfunction.
ABS IN Valve and ABS OUT Valve
When “Up”, “Keep” or “Down” is selected on display scr een, the following items are displayed when system is
normal.
*: Immediately after being selected, status is “O n”. Status changes to “Off” after approx. 2 seconds.
ABS IN Valve (ACT) and ABS OUT Valve (ACT)
When “Up”, “ACT KEEP” or “ACT UP” is selected on display screen, the following items are displayed when
system is normal.
Test item Display Item Display
Up Keep Down
FR RH SOL FR RH IN SOL Off On* On*
FR RH OUT SOL Off Off On*
FR LH SOL FRLH IN SOL Off On* On*
FR LH OUT SOL Off Off On*
RR RH SOL RR RH IN SOL Off On* On*
RR RH OUT SOL Off Off On*
RR LH SOL RR LH IN SOL Off On* On*
RR LH OUT SOL Off Off On*
Test item Display Item Display
Up ACT KEEP ACT UP
FR RH SOL (ACT) FR RH IN SOL Off Off On*
FR RH OUT SOL Off Off Off
CV1 Off On* On*
SV1 Off Off On*
FR LH SOL (ACT) FR LH IN SOL Off Off On*
FR LH OUT SOL Off Off Off
CV1 Off On* On*
SV1 Off Off On*
RR RH SOL (ACT) RR RH IN SOL Off Off On*
RR RH OUT SOL Off Off Off
CV2 Off On* On*
SV2 Off Off On*
RR LH SOL (ACT) RR LH IN SOL Off Off On*
RR LH OUT SOL Off Off Off
CV2 Off On* On*
SV2 Off Off On*
Revision: 2010 May2011 QX56

BRC-44
< SYSTEM DESCRIPTION >[WITH VDC]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
*: Immediately after being selected, status is “O n”. Status changes to “Off” after approx. 2 seconds.
Stop Lamp ON Relay
When “On” or “Off” is selected on display screen, t he following items are displayed when system is normal.
NOTE:
Display occasionally changes On/Off for a moment after ignition switch is turned ON. This is operation for
checking purposes and is not a malfunction.
WORK SUPPORT
Test item Display Item Display
On Off
STOP LAMP ON RELAY STOP LAMP ON RELAY On Off
Conditions Description
ST ANGLE SENSOR ADJUSTMENT Perform neutral position adjustment of steering angle sensor.
DECEL G SENSOR CALIBRATION Perform decel G sensor calibration.
Revision: 2010 May2011 QX56

BRC-50
< ECU DIAGNOSIS INFORMATION >[WITH VDC]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
*1: Models with 4WD System
*2: Models with Advanced Driver Assistance System
Protection FunctionINFOID:0000000006222581
The VDC warning lamp, ABS warning lamp and brake warning lamp turns ON and DTC “C118E” may be
detected in self-diagnosis result of “ABS” when the br
ake pedal is excessively operated, such as air bleeding.
This is not a system malfunction because this occurs due to the temporary decrease in accumulator fluid pres-
sure. The system returns to normal condition when the accu mulator fluid pressure reaches the specified pres-
sure with the ignition switch ON and the VDC warning lamp, ABS warning lamp, and brake warning lamp turn
OFF. After these steps, erase self-diagnos is results for “ABS” with CONSULT-III.
NOTE:
D T C “ C 1111 ” i s d e t e c t e d i n s e l f - d i agnosis results of “ABS” when the a ccumulator system has a malfunction.
DTC Inspection Priority ChartINFOID:0000000006222582
When multiple DTCs are displayed simultaneously, check one by one depending on the following priority list.
C1170 When the information in ABS actuator and electric unit (control unit) is not the same. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C118E When performing excessive brake pedal operation with the vehicle stopped. [When
accumulator fluid pressure reaches 11.43 MPa (114 bar, 116.6 kg/cm
2, 1657 psi) af-
ter reaching 17.3 MPa (173 bar, 176.5 kg/cm2, 2509 psi.] The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
U1000 When CAN communication signal is not continuously received for 2 seconds or
more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
DTC Malfunction detected condition Fail-safe condition
DTC
 VDC warning lamp
 ABS warning lamp
 Brake warning lamp Condition Description protection function
C118E ON When temporary decrease in accumulator fluid pres-
sure.
NOTE:
System is not malfunction. The following functions are suspended
temporarily
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD)
function
Priority Detected item (DTC)
1  U1000 CAN COMM CIRCUIT
2  C1170 VARIANT CODING
Revision: 2010 May2011 QX56

BRC-68
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1101, C1102, C1103,
C1104 WHEEL SENSOR
DTC/CIRCUIT DIAGNOSIS
C1101, C1102, C1103, C1104 WHEEL SENSOR
DTC LogicINFOID:0000000006222592
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C1101”, “C1102”, “C1103” or “C1104” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-68, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222593
CAUTION:
Never check between wheel sensor harness connector terminals.
1.CHECK WHEEL SENSOR HARNESS
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Disconnect wheel sensor harness connector.
4. Check continuity between ABS actuator and electr ic unit (control unit) harness connector and wheel sen-
sor harness connector. (Check continuity when steering wheel is steered to RH and LH, or center harness
in wheel housing is moved.)
Measurement connector and termi nal for power supply circuit
Measurement connector and te rminal for signal circuit
DTC Display Item Malfunction detected condition Possible causes
C1101 RR RH SENSOR-1 When an open circuit is detected in rear RH wheel
sensor circuit.
 Harness or connector
 Wheel sensor
 ABS actuator and electric unit (control unit)
C1102 RR LH SENSOR-1
When an open circuit is detected in rear LH wheel
sensor circuit.
C1103 FR RH SENSOR-1 When an open circuit is detected in front RH wheel
sensor circuit.
C1104 FR LH SENSOR-1 When an open circuit is detected in front LH wheel
sensor circuit.
ABS actuator and electric unit
(control unit) Wheel sensor
Continuity
Connector Terminal Connector Terminal
E36 20 E22 (Front LH wheel)
1 Existed
33 E39 (Front RH wheel)
22 C10 (Rear LH wheel)
35 C11 (Rear RH wheel)
ABS actuator and electric unit (control unit) Wheel sensor
Continuity
Connector Terminal Connector Terminal
E36 34 E22 (Front LH wheel)
2 Existed
19 E39 (Front RH wheel)
36 C10 (Rear LH wheel)
21 C11 (Rear RH wheel)
Revision: 2010 May2011 QX56

BRC-70
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1105, C1106, C1107,
C1108 WHEEL SENSOR
C1105, C1106, C1107, C1108 WHEEL SENSOR
DTC LogicINFOID:0000000006222594
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Start engine and drive vehicle at approx. 30 km/h (19 MPH) or more for approx. 1 minute.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C1105”, “C1106”, “C1107” or “C1108” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-70, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222595
CAUTION:
Never check between wheel sensor harness connector terminals.
1.CHECK WHEEL SENSOR HARNESS
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Disconnect wheel sensor harness connector.
4. Check continuity between ABS actuator and electr ic unit (control unit) harness connector and the ground.
DTC Display Item Malfunction detected condition Possible causes
C1105 RR RH SENSOR-2  When power supply voltage of rear RH wheel sen-
sor is low.
 When distance between rear RH wheel sensor and rear RH wheel sensor rotor is large.
 When installation of rear RH wheel sensor or rear
RH wheel sensor rotor is not normal.
 Harness or connector
 Wheel sensor
 ABS actuator and electric unit (control unit)
 Sensor rotor
C1106 RR LH SENSOR-2
 When power supply voltage of rear LH wheel sen-
sor is low.
 When distance between rear LH wheel sensor and
rear LH wheel sensor rotor is large.
 When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not normal.
C1107 FR RH SENSOR-2  When power supply voltage of front RH wheel sen-
sor is low.
 When distance between front RH wheel sensor and front RH wheel sensor rotor is large.
 When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
C1108 FR LH SENSOR-2  When power supply voltage of front LH wheel sen-
sor is low.
 When distance between front LH wheel sensor and
front LH wheel sensor rotor is large.
 When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
Revision: 2010 May2011 QX56

BRC-72
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1109 POWER AND
GROUND SYSTEM
C1109 POWER AND GROUND SYSTEM
DescriptionINFOID:0000000006222596
Ignition power supply is supplied to ABS actuator and electric unit (control unit).
DTC LogicINFOID:0000000006222597
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Start the engine. Drive the vehicle at vehicle speed of approx. 10 km/h (6 MPH) or more for approx. 10
seconds.
2. Perform self-diagnosis for “ABS”
Is DTC
“C1109” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-72, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222598
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) IGNITION POWER SUPPLY (1)
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
4. Turn the ignition switch ON. CAUTION:
Never start engine.
5. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CON TROL UNIT) IGNITION POWER SUPPLY CIRCUIT
(1)
1. Turn the ignition switch OFF.
2. Check 10A fuse (#57).
3. Disconnect IPDM E/R harness connector.
DTC Display Item Malfunction detected condition Possible causes
C1109 BATTERY VOLTAGE
[ABNORMAL]  When ignition voltage is 10 V or less.
 When ignition voltage is 16 V or more.  Harness or connector
 ABS actuator and electric unit
(control unit)
Fuse
 Ignition power supply system
 Battery
ABS actuator and electric unit (control unit) —Voltage
Connector Terminal
E36 18 Ground Approx. 0 V
ABS actuator and electric unit (control unit) —Voltage
Connector Terminal
E36 18 Ground 10 − 16 V
Revision: 2010 May2011 QX56

C1111 PUMP MOTORBRC-75
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1111 PUMP MOTOR
DTC LogicINFOID:0000000006222599
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF and depress the brake pedal 20 times or more.
2. Start the engine and wait for 3 minutes or more. CAUTION:
Never drive the vehicle.
3. Depress the brake pedal, and then operate the ABS act uator and electric unit (control unit) motor repeats
ON and OFF 4 times or more.
CAUTION:
Never drive the vehicle.
4. Perform self-diagnosis for “ABS”.
Is DTC
“C 1111” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-75, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222600
1.CHECK ABS MOTOR AND MOTOR RELAY POWER SUPPLY
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
4. Turn the ignition switch ON. CAUTION:
Never start engine.
5. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK ABS MOTOR AND MOTOR RELAY POWER SUPPLY CIRCUIT
DTC Display Item Malfunction detected condition Possible causes
C 1111 P U M P M O T O R  When a malfunction is detected in motor or motor
relay.
 When a low pressure malfunction is detected in ac- cumulator.
 When a malfunction is detected in accumulator
pressure sensor.  Harness or connector
 ABS actuator and electric unit
(control unit)
Fusible link
 Battery power supply system
 Motor/accumulator assembly
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 4 Ground Battery voltage
E37 47
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 4 Ground Battery voltage
E37 47
Revision: 2010 May2011 QX56