2011 INFINITI QX56 brake sensor

DAS
DIAGNOSIS SYSTEM (ADAS CONTROL UNIT)
DAS-81
< SYSTEM DESCRIPTION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
Display Items for The Cause of Automatic Cancellation 2
SELF DIAGNOSTIC RESULT
Refer to DAS-38, "DTC Index".
DATA MONITOR
INCHING LOST ×A vehicle ahead is not detected during the following driving when
the vehicle speed is approximately 24 km/h (15 MPH) or less
CAN COMM ERROR ×××ADAS control unit received an abnormal signal with CAN commu-
nication
ABS/TCS/VDC CIRC ×××An abnormal condition occurs in VDC/TCS/ABS system
ECD CIRCUIT ×××An abnormal condition occurs in ECD system
ASCD VHCL SPD DTAC ×Vehicle speed is detached from set vehicle speed
ASCD DOUBLE COMD ×Cancel switch and operation switch are detected simultaneously
APA HI TEMP ×The accelerator pedal actuator integrated motor temperature is
high
ICC SENSOR CAN
COMM ERR ××Communication error between ADAS control unit and the ICC sen-
sor
4WD LOCK MODE ×××Shifting of the 4WD shift switch to 4H or 4L
ABS WARNING LAMP ××ABS warning lamp ON
NO RECORD ××× —
Cause of cancellation Description
OPE VDC/TCS/ABS 1 The activation of VDC, TCS, or ABS during LDP system control
Vehicle dynamics Vehicle behavior exceeds specified value
Steering speed Steering speed was more than the specified value in evasive direction
End by yaw angle Yaw angle was the end of LDP control
Departure yaw large Detected more than the specified value of yaw angle in departure direction
ICC WARNING Target approach warning of ICC system, IBA system or FCW system was activated
CURVATURE Road curve was more than the specified value
Steering angle large Steering angle was more than the specified value
Brake is operated Brake pedal was operated
IGN LOW VOLT Decrease in ADAS control unit IGN voltage
Lateral offset Distance of vehicle and lane was detached in lateral direction more than the specified value
Lane marker lost Lane camera unit lost the trace of lane marker
Lane marker unclear Detected lane marker was unclear
Yaw acceleration Detected yawing speed was more than the specified value
Deceleration large Deceleration in a longitudinal direction was more than the specified value
Accel is operated Accelerator pedal was depressed
Departure steering Steering wheel was steered more than the specified value in departure direction
Evasive steering Steering wheel was steered more than the specified value in the evasive direction
R range Selector lever was operated to R range
Parking brake drift Rear wheels lock was detected
Not operating condition Did not meet the operating condition (vehicle speed, turn signal operation, etc)
SNOW MODE SW SNOW mo de switch was pressed
VDC OFF SW VDC OFF switch was pressed
OPE VDC/ABS 2 The activation of VDC or ABS duri ng a standby time of LDP system control
4WD LOCK MODE Shifting of the 4WD shift switch to 4H or 4L
NO RECORD —
Revision: 2010 May2011 QX56

DAS-82
< SYSTEM DESCRIPTION >[DCA]
DIAGNOSIS SYSTEM (ADAS CONTROL UNIT)
Monitored item
[Unit]
ALL SIG(ICC)
MAIN SIG (ICC)
MAIN SIG
(LDW/LDP)
MAIN SIG
(BSW/BSI)
Description
MAIN SW
[On/Off] ×× × × Indicates [On/Off] status as judged from ICC steering switch signal (ECM trans-
mits ICC steering switch signal through CAN communication)
SET/COAST SW
[On/Off] ×× Indicates [On/Off] status as judged from ICC steering switch signal (ECM trans-
mits ICC steering switch signal through CAN communication)
CANCEL SW
[On/Off] ××
Indicates [On/Off] status as judged from ICC steering switch signal (ECM trans-
mits ICC steering switch signal through CAN communication)
RESUME/ACC SW
[On/Off] ×× Indicates [On/Off] status as judged from ICC steering switch signal (ECM trans-
mits ICC steering switch signal through CAN communication)
DISTANCE SW
[On/Off] × Indicates [On/Off] status as judged from ICC steering switch signal (ECM trans-
mits ICC steering switch signal through CAN communication)
CRUISE OPE
[On/Off] ××
Indicates whether controlling or not (ON means “controlling”)
BRAKE SW
[On/Off] ×× × × Indicates [On/Off] status as judged from ICC brake switch signal (ECM transmits
ICC brake switch signal through CAN communication)
STOP LAMP SW
[On/Off] ×× × × Indicates [On/Off] status as judged from stop lamp switch signal (ECM transmits
stop lamp switch signal through CAN communication)
IDLE SW
[On/Off] ×
Indicates [On/Off] status of idle switch read from ADAS control unit through CAN
communication (ECM transmits On/Off status through CAN communication)
SET DISTANCE
[Short/Mid/Long] ××
Indicates set distance memorized in ADAS control unit
CRUISE LAMP
[On/Off] ××
Indicates [On/Off] status of MAIN switch indicator output
OWN VHCL
[On/Off] ×
Indicates [On/Off] status of own vehicle indicator output
VHCL AHEAD
[On/Off] ×
Indicates [On/Off] status of vehicle ahead detection indicator output
ICC WARNING
[On/Off] ×
Indicates [On/Off] status of ICC system warning lamp output
VHCL SPEED SE
[km/h] or [mph] ×× × × Indicates vehicle speed calculated from ADAS control unit through CAN commu-
nication [ABS actuator and electric unit (c
ontrol unit) transmits vehicle speed sig-
nal (wheel speed) through CAN communication]
SET VHCL SPD
[km/h] or [mph] ××
Indicates set vehicle speed memorized in ADAS control unit
BUZZER O/P
[On/Off] ×
Indicates [On/Off] status of ICC warning chime output
THRTL SENSOR
[deg] ××
NOTE:
The item is displayed, but it is not monitored
ENGINE RPM
[rpm] × Indicates engine speed read from ADAS control unit through CAN communication
(ECM transmits engine speed signal through CAN communication)
WIPER SW
[OFF/LOW/HIGH] × Indicates wiper [OFF/LOW/HIGH] status (BCM transmits front wiper request sig-
nal through CAN communication)
YAW R AT E
[deg/s] ×
NOTE:
The item is displayed, but it is not monitored
BA WARNING
[On/Off] ×
Indicates [On/Off] status of IBA OFF indicator lamp output
STP LMP DRIVE
[On/Off] ××
Indicates [On/Off] status of ICC brake hold relay drive output
D RANGE SW
[On/Off] × Indicates [On/Off] status of “D” or “M” positions read from ADAS control unit
through CAN communication; ON when position “D” or “M” (TCM transmits shift
position signal through CAN communication).
Revision: 2010 May2011 QX56

DAS
DIAGNOSIS SYSTEM (ADAS CONTROL UNIT)
DAS-83
< SYSTEM DESCRIPTION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
NP RANGE SW
[On/Off] × Indicates shift position signal read from ADAS control unit through CAN commu-
nication (TCM transmits shift position signal through CAN communication)
PKB SW
[On/Off] × Parking brake switch status [On/Off] judged from the parking brake switch signal
that ADAS control unit readout via CAN communication is displayed (Combination
meter transmits the parking brake switch signal via CAN communication)
PWR SUP MONI
[V] ××
Indicates IGN voltage input by ADAS control unit
VHCL SPD AT
[km/h] or [mph] × Indicates vehicle speed calculated from A/T vehicle speed sensor read from
ADAS control unit through CAN communication (TCM transmits A/T vehicle speed
sensor signal through CAN communication)
THRTL OPENING
[%] ×× Indicates throttle position read from ADAS control unit through CAN communica-
tion (ECM transmits accelerator pedal position signal through CAN communica-
tion).
GEAR
[1, 2, 3, 4, 5, 6, 7] × Indicates A/T gear position read from ADAS control unit through CAN communi-
cation (TCM transmits current gear position signal through CAN communication)
MODE SIG
[OFF, ICC, ASCD] × Indicates the active mode from ICC or ASCD [conventional (fixed speed) cruise
control mode]
SET DISP IND
[On/Off] ×
Indicates [On/Off] status of SET switch indicator output
DISTANCE
[m] ×
Indicates the distance from the vehicle ahead
RELATIVE SPD
[m/s] ×
Indicates the relative speed of the vehicle ahead
DYNA ASIST SW
[On/Off] ×× ×
Indicates [On/Off] status as judged from ICC steering switch signal (ECM trans-
mits ICC steering switch signal through CAN communication)
DCA ON IND
[On/Off] ×
The status [ON/OFF] of DCA system switch indicator output is displayed
DCA VHL AHED
[On/Off] × The status [ON/OFF] of vehicle ahead detection indicator output in DCA system
is displayed
IBA SW
[On/Off] ××
Indicates [On/Off] status of IBA OFF switch
FCW SYSTEM ON
[On/Off] ××
Indicates [On/Off] status of FCW system
APA TEMP
[ ° C] × Accelerator pedal actuator integrated motor temperature that the ADAS control
unit readout via ITS communication is displayed (Accelerator pedal actuator trans-
mits the integrated motor temperature via ITS communication)
APA PWR
[V] × Accelerator pedal actuator power supply voltage that the ADAS control unit read-
out via ITS communication is displayed (Accelerator pedal actuator transmits the
power supply voltage via ITS communication)
LDW SYSTEM ON
[On/Off] ×
Indicates [On/Off] status of LDW system
LDW ON LAMP
[On/Off] ×
Indicates [On/Off] status of waning systems ON indicator output
LDP ON IND
[On/Off] ×
Indicates [On/Off] status of LDP ON indicator lamp (Green) output
LANE DPRT W/L
[On/Off] ×
Indicates [On/Off] status of lane departure warning lamp (Yellow) output
LDW BUZER OUT-
PUT
[On/Off] ×
Indicates [On/Off] status of warning buzzer output
Monitored item
[Unit]
ALL SIG
(ICC)
MAIN SIG (ICC)
MAIN SIG
(LDW/LDP)
MAIN SIG
(BSW/BSI)
Description
Revision: 2010 May2011 QX56

DAS-94
< ECU DIAGNOSIS INFORMATION >[DCA]
ADAS CONTROL UNIT
VHCL SPEED SE While driving Displays the ve-
hicle speed cal-
culated by
ADAS control unit
SET VHCL SPD While driving When vehicle speed is set Displays the set
vehicle speed
BUZZER O/P Engine running When the buzzer of the following system operates
 Vehicle-to-vehicle distance control mode
 DCA system
 FCW system
 IBA system
On
When the buzzer of the following system not operates
 Vehicle-to-vehicle distance control mode
 DCA system
 FCW system
 IBA system Off
THRTL SENSOR NOTE:
The item is indicated, but not monitored
0.0
ENGINE RPM Engine running Equivalent to ta-
chometer read- ing
WIPER SW Ignition switch ON Wiper not operating Off
Wiper LO operation Low
Wiper HI operation High
YAW R AT E NOTE:
The item is indicated, but not monitored
0.0
BA WARNING Engine running IBA OFF indicator lamp ON
 When IBA system is malfunctioning
 When IBA system is turned to OFF
On
IBA OFF indicator lamp OFF
 When IBA system is normal
 When IBA system is turned to ON Off
STP LMP DRIVE Drive the vehicle and activate
the vehicle-to-vehicle distance
control mode When ICC brake hold relay is activated On
When ICC brake hold relay is not activated Off
D RANGE SW Engine running When the selector lever is in “D” position or manual
mode
On
When the selector lever is in any position other than “D”
or manual mode Off
NP RANGE SW Engine running When the selector lever is
in “N”, “P” position On
When the selector lever is in any position other than “N”,
“P” Off
PKB SW Ignition switch ON When the parking brake is applied On
When the parking brake is released Off
PWR SUP MONI Engine running Power supply
voltage value of ADAS control unit
VHCL SPD AT While driving Va l u e o f A / T v e -
hicle speed sen- sor signal
THRTL OPENING Engine running Depress accelerator pedal Displays the
throttle position
Monitor item Condition Value/Status
Revision: 2010 May2011 QX56

DAS-100
< ECU DIAGNOSIS INFORMATION >[DCA]
ADAS CONTROL UNIT
DTC Index
INFOID:0000000006223513
NOTE:
 The details of time display are as per the following.
4  C1A01: POWER SUPPLY CIR
 C1A02: POWER SUPPLY CIR 2
 C1A04: ABS/TCS/VDC CIRC
 C1A05: BRAKE SW/STOP L SW
 C1A06: OPERATION SW CIRC
 C1A12: LASER BEAM OFFCNTR
 C1A13: STOP LAMP RLY FIX
 C1A14: ECM CIRCUIT
 C1A16: RADAR STAIN
 C1A18: LASER AIMING INCMP
 C1A2A: ICC SEN PWR SUP CIR
 C1A21: ICC SENSOR HIGH TEMP
 C1A24: NP RANGE
 C1A26: ECD MODE MALF
 C1A27: ECD PWR SUPLY CIR
 C1A33: CAN TRANSMISSION ERR
 C1A34: COMMAND ERROR
 C1A35: APA CIR
 C1A36: APA CAN COMM CIR
 C1A37: APA CAN CIR 2
 C1A38: APA CAN CIR 1
 C1A39: STRG SEN CIR
 C1A40: SYSTEM SW CIRC
 C1B01: CAM AIMING INCMP
 C1B03: CAM ABNRML TMP DETCT
 C1F01: APA MOTOR MALF
 C1F05: APA PWR SUPLY CIR
 U0121: VDC CAN CIR 2
 U0126: STRG SEN CAN CIR 1
 U0235: ICC SENSOR CAN CIRC 1
 U0401: ECM CAN CIR 1
 U0402: TCM CAN CIR 1
 U0415: VDC CAN CIR 1
 U0428: STRG SEN CAN CIR 2
 U1500: CAM CAN CIR 2
 U1501: CAM CAN CIR 1
 U1502: ICC SEN CAN COMM CIR
 U1503: SIDE RDR L CAN CIR 2
 U1504: SIDE RDR L CAN CIR 1
 U1505: SIDE RDR R CAN CIR 2
 U1506: SIDE RDR R CAN CIR 1
 U150B: ECM CAN CIRC 3
 U150C: VDC CAN CIRC 3
 U150D: TCM CAN CIRC 3
 U150E: BCM CAN CIRC 3
 U150F: AV CAN CIRC 3
 U1512: HVAC CAN CIRC3
 U1513: METER CAN CIRC 3
 U1514: STRG SEN CAN CIRC 3
 U1515: ICC SENSOR CAN CIRC 3
 U1516: CAM CAN CIRC 3
 U1517: APA CAN CIRC 3
 U1518: SIDE RDR L CAN CIRC 3
 U1519: SIDE RDR R CAN CIRC 3
 U1520: 4WD CAN CIRC 3
5  C1A03: VHCL SPEED SE CIRC
6  C1A15: GEAR POSITION
7  C1A00: CONTROL UNIT
Priority Detected items (DTC)
Revision: 2010 May2011 QX56

DAS
ADAS CONTROL UNITDAS-101
< ECU DIAGNOSIS INFORMATION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past
 IGN counter is displayed on FFD (Freeze Frame Data).
- 0: The malfunctions that are detected now CAN communication system (U1000, U1010)
- 1 - 39: It increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 39, it is fixed to 39 unt il the self-diagnosis results are erased.
Other than CAN communication s ystem (Other than U1000, U1010)
- 1 - 49: It increases like 0 → 1 → 2 ··· 38 → 49 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 49, it is fixed to 49 unt il the self-diagnosis results are erased.
Systems for fail-safe
 A: Vehicle-to-vehicle distance control mode
 B: Conventional (fixed speed) cruise control mode
 C: Intelligent Brake Assist (IBA)
 D: Forward Collision Warning (FCW)
 E: Distance Control Assist (DCA)
 F: Lane Departure Warning (LDW)/Lane Departure Prevention (LDP)
 G: Blind Spot Warning (BSW)
DTC
CONSULT-III display Warning lamp Fail-safe
Reference
CONSULT-III On board
display
ICC system warning lamp
IBA OFF indicator lamp
Lane departure warning lamp BSW warning lamp
System
C1A00 0 CONTROL UNIT ON ON ON ON A, B, C, D, E, F, G DAS-129
C1A01 1 POWER SUPPLY CIR ON ON ON ON A, B, C, D, E, F, GDAS-130
C1A02 2 POWER SUPPLY CIR 2 ON ON ON ON A, B, C, D, E, F, GDAS-130
C1A03 3 VHCL SPEED SE CIRC ON ON ON ON A, B, C, D, E, F, GDAS-131
C1A04 4 ABS/TCS/VDC CIRC ON ON ON A, B, C, D, E, FDAS-133
C1A05 5 BRAKE SW/STOP L SW ON ON ON A, B, C, D, E, FDAS-134
C1A06 6 OPERATION SW CIRC ON ON A, B, E, FDAS-138
C1A12 12LASER BEAM OFFCN-
TR ON ON A, C, D, E
DAS-140
C1A13 13 STOP LAMP RLY FIX ON ON A, B, C, D, E DAS-141
C1A14 14 ECM CIRCUIT ON ON A, B, E, FDAS-147
C1A15 15 GEAR POSITION ON ON ON ON A, B, C, D, E, F, GDAS-148
C1A16 16 RADAR STAIN ON ON A, C, D, EDAS-150
C1A17 17 ICC SENSOR MALF ON ON A, B, C, D, EDAS-151
C1A18 18 LASER AIMING INCMP ON ON A, C, D, EDAS-152
C1A21 21ICC SENSOR HIGH
TEMP ON ON A, B, C, D, E
DAS-153
C1A24 24 NP RANGE ON ON ON ON A, B, C, D, E, F, G DAS-154
C1A26 26 ECD MODE MALF ON ON A, B, C, D, EDAS-156
C1A27 27 ECD PWR SUPLY CIR ON ON A, B, C, D, EDAS-157
C1A33 33CAN TRANSMISSION
ERR ON A, B, E
DAS-159
Revision: 2010 May2011 QX56

DAS-102
< ECU DIAGNOSIS INFORMATION >[DCA]
ADAS CONTROL UNIT
C1A34 34 COMMAND ERROR ON A, B, E
DAS-160
C1A35 35 APA CIR ON A, EDAS-161
C1A36 36 APA CAN COMM CIR ON A, EDAS-162
C1A37 133 APA CAN CIR 2 ON A, B, EDAS-163
C1A38 132 APA CAN CIR 1 ON A, B, EDAS-164
C1A39 39 STRG SEN CIR ON ON ON A, B, C, D, E, GDAS-165
C1A40 40 SYSTEM SW CIRC ON C, DCCS-126
C1A2A 80 ICC SEN PWR SUP CIR ON ON A, C, D, E DAS-158
C1B00 81 CAMERA UNIT MALF ON FDAS-361
C1B01 82 CAM AIMING INCMP ON FDAS-363
C1B03 83CAM ABNRML TMP DE-
TCT BLINK F
DAS-365
C1B53 84 SIDE RDR R MALF ON G DAS-482
C1B54 85 SIDE RDR L MALF ON GDAS-483
C1F01 91 APA MOTOR MALF ON A, EDAS-166
C1F02 92 APA C/U MALF ON A, EDAS-168
C1F05 95 APA PWR SUPLY CIR ON A, EDAS-171
NO DTC IS
DETECTED.
FURTHER TESTING
MAY BE RE-
QUIRED 55
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED ———— — —
U0121 127 VDC CAN CIR 2 ON ON ON ON A, B, C, D, E, F, G DAS-175
U0126 130 STRG SEN CAN CIR 1 ON ON ON A, B, C, D, E, GDAS-176
U0235 144 ICC SENSOR CAN
CIRC 1 ON ON A, B, C, D, E
DAS-177
U0401 120 ECM CAN CIR 1 ON ON ON A, B, E, F, G DAS-178
U0402 122 TCM CAN CIR 1 ON ON ON ON A, B, C, D, E, F, GDAS-179
U0415 126 VDC CAN CIR 1 ON ON ON ON A, B, C, D, E, F, GDAS-180
U0428 131 STRG SEN CAN CIR 2 ON ON ON A, B, C, D, E, GDAS-181
U1000NOTE100 CAN COMM CIRCUIT ON ON ON ON A, B, C, D, E, F, GDAS-182
U1010 110 CONTROL UNIT (CAN) ON ON ON ON A, B, C, D, E, F, G DAS-184
Systems for fail-safe
 A: Vehicle-to-vehicle distance control mode
 B: Conventional (fixed speed) cruise control mode
 C: Intelligent Brake Assist (IBA)
 D: Forward Collision Warning (FCW)
 E: Distance Control Assist (DCA)
 F: Lane Departure Warning (LDW)/Lane Departure Prevention (LDP)
 G: Blind Spot Warning (BSW)
DTC
CONSULT-III display Warning lamp Fail-safe
Reference
CONSULT-III On board
display
ICC system warning lamp
IBA OFF indicator lamp
Lane departure warning lamp
BSW warning lamp
System
Revision: 2010 May2011 QX56

DAS
ADAS CONTROL UNITDAS-103
< ECU DIAGNOSIS INFORMATION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
NOTE:
With the detection of “U1000” some syst ems do not perform the fail-safe operation.
A system controlling based on a signal received from the control unit performs fail-safe operation when the
communication with the ADAS control unit becomes inoperable.
U1500 145 CAM CAN CIR 2 ON F DAS-381
U1501 146 CAM CAN CIR 1 ON FDAS-382
U1502 147ICC SEN CAN COMM
CIR ON ON A, B, C, D, E
DAS-189
U1503 150 SIDE RDR L CAN CIR 2 ON G DAS-502
U1504 151 SIDE RDR L CAN CIR 1 ON GDAS-503
U1505 152 SIDE RDR R CAN CIR 2 ON GDAS-504
U1506 153 SIDE RDR R CAN CIR 1 ON GDAS-505
U1507 154LOST COMM (SIDE
RDR R) ON G
DAS-506
U1508 155LOST COMM (SIDE
RDR L) ON G
DAS-507
U150B 157 ECM CAN CIRC 3 ON ON ON A, B, E, F, G DAS-185
U150C 158 VDC CAN CIRC 3 ON ON ON ON A, B, C, D, E, F, G DAS-186
U150D 159 TCM CAN CIRC 3 ON ON ON ON A, B, C, D, E, F, GDAS-187
U150E 160 BCM CAN CIRC 3 ON ON ON A, B, E, F, GDAS-188
U150F 161 AV CAN CIRC 3 DAS-61
U1512 162 HVAC CAN CIRC3 ON FDAS-383
U1513 163 METER CAN CIRC 3 ON ON ON ON A, B, C, D, E, F, GDAS-190
U1514 164 STRG SEN CAN CIRC 3 ON ON ON A, B, C, D, E, GDAS-191
U1515 165 ICC SENSOR CAN
CIRC 3 ON ON A, B, C, D, E
DAS-192
U1516 166 CAM CAN CIRC 3 ON F DAS-385
U1517 167 APA CAN CIRC 3 ON A, B, EDAS-193
U1518 168 SIDE RDR L CAN CIRC 3 ON GDAS-510
U1519 169SIDE RDR R CAN CIRC
3 ON G
DAS-511
U1520 176 4WD CAN CIRC 3 ON ON ON A, B, C, D, E, F DAS-194
Systems for fail-safe
 A: Vehicle-to-vehicle distance control mode
 B: Conventional (fixed speed) cruise control mode
 C: Intelligent Brake Assist (IBA)
 D: Forward Collision Warning (FCW)
 E: Distance Control Assist (DCA)
 F: Lane Departure Warning (LDW)/Lane Departure Prevention (LDP)
 G: Blind Spot Warning (BSW)
DTC
CONSULT-III display Warning lamp Fail-safe
Reference
CONSULT-III On board
display
ICC system warning lamp
IBA OFF indicator lamp
Lane departure warning lamp BSW warning lamp
System
Revision: 2010 May2011 QX56