2011 INFINITI QX56 parking brake

TM-16
< SYSTEM DESCRIPTION >[7AT: RE7R01B]
STRUCTURE AND OPERATION
STRUCTURE AND OPERATION
TRANSMISSION
TRANSMISSION : Cross-Sectional ViewINFOID:0000000006226762
2WD MODELS
4WD MODELS
1. Low brake 2. Drum support 3. Reverse brake
4. Direct clutch 5. High and low reverse clutch 6. 2nd one-way clutch
7.
*1Rear carrier 8. Mid carrier 9. Input clutch
10.
*2Front sun gear 11 .*3Front carrier 12. Under drive carrier
13. 1st one-way clutch 14. Front brake 15. 2346 brake
16.
*4Input shaft 17. Torque converter 18. Oil pump
19.
*2Under drive sun gear 20.*3Under drive internal gear21.*4Front internal gear
22. Mid sun gear 23.
*1Mid internal gear 24. Rear sun gear
25. Rear internal gear 26. High and low reverse clutch hub 27. Control valve & TCM
28. Parking gear 29. Adapter case 30. Output shaft
*1: 7 and 23 are one unit.
*2: 10 and 19 are one unit.
*3: 11 and 20 are one unit.
*4: 16 and 21 are one unit.
JSDIA1852ZZ
Revision: 2010 May2011 QX56

STRUCTURE AND OPERATIONTM-17
< SYSTEM DESCRIPTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
1. Low brake 2. Drum support 3. Reverse brake
4. Direct clutch 5. High and low reverse clutch 6. 2nd one-way clutch
7.
*1Rear carrier 8. Mid carrier 9. Input clutch
10.
*2Front sun gear 11 .*3Front carrier 12. Under drive carrier
13. 1st one-way clutch 14. Front brake 15. 2346 brake
16.
*4Input shaft 17. Torque converter 18. Oil pump
19.
*2Under drive sun gear 20.*3Under drive internal gear21.*4Front internal gear
22. Mid sun gear 23.
*1Mid internal gear 24. Rear sun gear
25. Rear internal gear 26. High and low reverse clutch hub 27. Control valve & TCM
28. Parking gear 29. Adapter case 30. Output shaft
*1: 7 and 23 are one unit.
*2: 10 and 19 are one unit.
*3: 11 and 20 are one unit.
*4: 16 and 21 are one unit.
JSDIA1774ZZ
Revision: 2010 May2011 QX56

STRUCTURE AND OPERATIONTM-21
< SYSTEM DESCRIPTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
 The same as for the “N” position, since the low brake is released, so torque from the input shaft drive is not
transmitted to the output shaft.
 The parking pawl linked with the selector lever mes hes with the parking gear and fastens the output shaft
mechanically.
“D1” Position
JSDIA1277GB
Revision: 2010 May2011 QX56

A/T FLUIDTM-95
< BASIC INSPECTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
d. When the ATF starts to drip, tighten the drain plug to the oil pan to the specified torque. Refer to TM-182,
"Exploded View".
CAUTION:
Never reuse drain plug and drain plug gasket.
e. Remove overflow plug from oil pan.
f. Install the charging pipe (A) to the overflow plug hole. CAUTION:
Tighten the charging pipe by hand.
g. Install the bucket pump hose (B) to the charging pipe. CAUTION:
Insert the bucket pump hose all the way to the end of the
charging pipe.
h. Fill approximately 3 liters (3-1/8 US qt, 2-5/8 lmp qt) of the ATF.
i. Remove the bucket pump hose to remove the charging pipe, and then temporarily tighten the overflow plug to the oil pan.
CAUTION:
Quickly perform the procedure to avoid ATF leakage from
the oil pan.
j. Lift down the vehicle.
k. Start the engine.
l. Make the ATF temperature approximately 40 °C (104 °F).
NOTE:
The ATF level is greatly affected by the temperat ure. Always check the ATF temperature on “ATF TEMP
1” of “Data Monitor” using CONSULT-III.
m. Park vehicle on level surface and set parking brake.
n. Shift the selector lever through each gear pos ition. Leave selector lever in “P” position.
o. Lift up the vehicle when the ATF temperature reaches 40 °C (104 °F), and remove the overflow plug from
the oil pan.
CAUTION:
Perform “Step 4-o” with the engine at idle.
p. When the ATF starts to drip, tighten the overflow plug to the oil pan to the specified torque. Refer to TM-
182, "Exploded View".
CAUTION:
Never reuse overflow plug.
AdjustmentINFOID:0000000006226792
CAUTION:
 Use only Genuine NISSAN Matic S ATF. Never mix with other ATF.
 Using ATF other than Genuine NI SSAN Matic S ATF will cause deteri oration in driveability and A/T
durability, and may damage the A/T, which is not covered by the INFINITI new vehicle limited war-
ranty.
 When filling ATF, be careful not to sca tter heat generating parts such as exhaust.
 Always maintain the ATF temperature within between 35 °C (95 °F) and 45 °C (113 °F) while checking
with CONSULT-III when the ATF level adjustment is performed.
JSDIA1335ZZ
Recommended fluid and fluid capacity : Refer to TM-296, "General Specification".
Revision: 2010 May2011 QX56

TM-96
< BASIC INSPECTION >[7AT: RE7R01B]
A/T FLUID
1. Install the O-ring (315268E000) (A) to the charging pipe
(310811EA5A) (B).
2. Start the engine.
3. Make the ATF temperature approximately 40 °C (104 °F).
NOTE:
The ATF level is greatly affected by the temperature. Always
check the ATF temperature on “ATF TEMP 1” of “Data Monitor”
using CONSULT-III.
4. Park vehicle on level surface and set parking brake.
5. Shift the selector lever through each gear position. Leave selec- tor lever in “P” position.
6. Lift up the vehicle.
7. Check the ATF leakage from transmission.
8. Remove overflow plug from oil pan.
9. Install the charging pipe (A) to the overflow plug hole. CAUTION:
Tighten the charging pipe by hand.
10. Install the bucket pump hose (B) to the charging pipe. CAUTION:
Insert the bucket pump hose all the way to the end of the
charging pipe.
11. Fill approximately 0.5 liters (1/2 US qt, 1/2 lmp qt) of the ATF.
12. Check that the ATF leaks when removing the charging pipe and the bucket pump hose. If the A TF does not leak, refill the ATF.
CAUTION:
Perform “Step 12” with the engine at idle.
13. When the ATF starts to drip, tighten the overflow pl ug to the oil pan to the specified torque. Refer to TM-
182, "Exploded View".
CAUTION:
Never reuse overflow plug.
JSDIA1334ZZ
JSDIA1335ZZ
Revision: 2010 May2011 QX56

TM-100
< BASIC INSPECTION >[7AT: RE7R01B]
STALL TEST
STALL TEST
Inspection and JudgmentINFOID:0000000006226793
INSPECTION
1. Inspect the amount of engine oil. Replenish the engine oil if necessary.
2. Drive for about 10 minutes to warm up the vehicle
so that the A/T fluid temperature is 50 to 80°C (122 to
176 °F). Inspect the amount of AT F. Replenish if necessary.
3. Securely engage the parking brake so that the tires do not turn.
4. Start the engine, apply foot brake, and place selector lever in “D” position.
5. Gradually press down the accelerator pedal while holding down the foot brake.
6. Quickly read off the stall speed, and quickly release the accelerator pedal. CAUTION:
Never hold down the accelerator pedal for more than 5 seconds during this test.
7. Shift the selector lever to “N” position.
8. Cool down the ATF. CAUTION:
Run the engine at idle for at least 1 minute.
9. Repeat steps 5 through 8 with selector lever in “R” position.
JUDGMENT OF STALL TEST
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value position
Stall speed : Refer to TM-297, "Stall Speed".
Selector lever position
Possible location of malfunction
“D” and “M” “R”
Stal l s pe ed HO
 Low brake
 1st one-way clutch
 2nd one-way clutch
OH  Reverse brake
 1st one-way clutch
 2nd one-way clutch
L L  Engine and torque converter one-way clutch
H H  Line pressure low
Does not shift-up “D” or “M” position 1 → 2 Slipping in 2GR, 3GR, 4GR or 6GR 2346 brake slippage
Does not shift-up “D” or “M” position 2 → 3 Slipping in 3GR, 4GR or 5GR Direct clutch slippage
Does not shift-up “D” or “M” position 3 → 4 Slipping in 4GR, 5GR, 6GR or 7GR High and low reverse clutch slippage
Does not shift-up “D” or “M” position 4 → 5 Slipping in 5GR, 6GR or 7GR Input clutch slippage
Does not shift-up “D” or “M” position 5 → 6 Slipping in 2GR, 3GR, 4GR or 6GR 2346 brake slippage
Does not shift-up “D” or “M” position 6 → 7 Slipping in 7GR Front brake slippage
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-169
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM TABLE 2
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Function
trouble
Power transmis-
sion cannot be
performed Vehicle cannot run in all
position.
3 2 111111111
Driving is not possible in
“D” position. 3 2 111111111
Driving is not possible in
“R” position. 32111
Engine stall 4 5 5 6 3 2 1
Engine stalls when selec-
tor lever shifted “N” → “D”
or “R”. 455 3 2 1
Engine does not start in
“N” or “P” position. 312 1
Engine starts in position
other than “N” or “P”. 32 1
Poor operation Vehicle does not enter
parking condition.
12
Parking condition is not
cancelled. 12
Vehicle runs with A/T in
“P” position. 12
Vehicle moves forward
with the “R” position. 12
Vehicle runs with A/T in
“N” position. 12
Vehicle moves backward
with the “D” position. 12
Revision: 2010 May2011 QX56

TM-170
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to
TM-16, "TRANSMISSION : Cross-Sectional
View".Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Poor
perfor-
mance
Driving
perfor-
mance Shift point is high in “D” position.
Shift point is low in “D” position.
Large
shock
When
shifting
gears →
“D” position 1 2 2
→ “R” position 1 1 2
1GR ⇔ 2GR 1 2
2GR ⇔ 3GR 1 2
3GR ⇔ 4GR 2 1 2
4GR ⇔ 5GR 1 1 2
5GR ⇔ 6GR 1 1 2
6GR ⇔ 7GR 1 1 2
Downshift when accel-
erator pedal is de-
pressed 211111 11 2
Upshift when accelera-
tor pedal is released 211111 11 2
Lock-up 1 2
Judder Lock-up 1 2
Strange noise In “R” position 1 1 1 1 2
In “N” position 1 1 1 2
In “D” position 1 1 1 1 2
Engine at idle 1 1 1 2
Revision: 2010 May2011 QX56