2011 INFINITI QX56 parking brake

SYSTEM SYMPTOMTM-171
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to TM-16, "TRANSMISSION : Cross-Sectional
View".Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Func-
tion
trouble
Gear
does no
change“D” posi-
tion Locks in 1GR 1 1 1 2
Locks in 2GR
1
Locks in 3GR 1
Locks in 4GR 1
Locks in 5GR 1
Locks in 6GR 1
Locks in 7GR 1
1GR → 2GR 1 1 1 2
2GR → 3GR 1 2
3GR → 4GR 2111 2
4GR → 5GR 1 1 2
5GR → 6GR 1 2
6GR → 7GR 2111 2
5GR → 4GR 1 2
4GR → 3GR 2 1 2
3GR → 2GR 1 1 2
2GR → 1GR 1 1 1 2
Does not lock-up 1211111 11 2
“M” posi-
tion 1GR
⇔ 2GR 211111 11 2
2GR ⇔ 3GR 211111 11 2
3GR ⇔ 4GR 211111 11 2
4GR ⇔ 5GR 211111 11 2
5GR ⇔ 6GR 211111 11 2
6GR ⇔ 7GR 211111 11 2
Revision: 2010 May2011 QX56

TM-172
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Func-
tion
trouble
Poor
shift-
ingSlip
When
shifting
gears 1GR
⇔ 2GR 1 1 1 2
2GR ⇔ 3GR 1 1 2
3GR ⇔ 4GR 1 2 1 2
4GR ⇔ 5GR 1 1 1 2
5GR ⇔ 6GR 1 1 1 2
6GR ⇔ 7GR 1 1 1 2
En-
gine
brake
does
not
work “D” position
→ “M” position 1 1 1 1 1 2
“M” posi-
tion 7GR
→ 6GR 1 1 1 2
6GR → 5GR 1 1 1 2
5GR → 4GR 1 1 1 2
4GR → 3GR 1 2 1 2
3GR → 2GR 1 1 1 1 1 2
2GR → 1GR 1 1 1 1 2
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-173
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to TM-16, "TRANSMISSION : Cross-Sectional
View".
Func-
tion
trouble
Poor
pow-
er
trans-
mis-
sion
Slip With selector lever
in “D” position, ac-
celeration is ex-
tremely poor.
112 1 12
With selector lever
in “R” position, ac-
celeration is ex-
tremely poor. 11 11112
While starting off
by accelerating in
1GR, engine rac-
es. 112 1112
While accelerating
in 2GR, engine
races. 1 2 1 112
While accelerating
in 3GR, engine
races. 1 2 11 12
While accelerating
in 4GR, engine
races. 1 1 11 12
While accelerating
in 5GR, engine
races. 1 111 12
While accelerating
in 6GR, engine
races. 111112
While accelerating
in 7GR, engine
races. 1 111 2
Lock-up 1 1 1 2
No creep at all. 11211111 11121
Extremely large
creep. 1
Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Revision: 2010 May2011 QX56

TM-174
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to
TM-16, "TRANSMISSION : Cross-Sectional
View".Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
gear
1st one-way clutch
2nd one-way clutch
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Function
trouble
Power trans-
mission cannot
be performed
Vehicle cannot run in all position. 1 1 2 1 1 1 1 1 1 2 1
Driving is not possible in “D” posi-
tion.
11211111 11121
Driving is not possible in “R” posi-
tion. 1 111121
Engine stall 1
Engine stalls when selector lever
shifted “N” → “D” or “R”. 1
Engine does not start in “N” or “P”
position. 1
Engine starts in position other
than “N” or “P”.
Poor operation Vehicle does not enter parking
condition.
1
Parking condition is not cancelled. 1
Vehicle runs with A/T in “P” posi-
tion. 2111111 21
Vehicle moves forward with the
“R” position. 211111 2
Vehicle runs with A/T in “N” posi-
tion. 2111111 2
Vehicle moves backward with the
“D” position. 12
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-205
< UNIT REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
2WD
2WD : Exploded ViewINFOID:0000000006233263
2WD : Removal and InstallationINFOID:0000000006233264
REMOVAL
CAUTION:
 When removing the A/T assembly from engine, fi rst remove the crankshaft position sensor (POS)
from the A/T assembly.
 Be careful not to damage sensor edge.
1. Shift the selector lever to “P” position, and release the parking brake.
2. Disconnect the battery cabl e from the negative terminal.
3. Support A/T assembly with a transmission jack. CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug and
overflow plug.
4. Remove rear engine mounting cross member.
5. Remove engine mounting insulator (rear).
6. Remove control cable from A/T assembly. Refer to TM-178, "
Removal and Installation".
7. Disconnect heated oxygen sensor 2 connectors (bank 1 and bank 2). Refer to EX-5, "
Exploded View".
1. A/T assembly 2. Front suspension rear cross mem-
ber3. Rear engine mounting cross
member
4. Engine mounting insulator (rear)
A. Tightening must be done following the installation procedure. Refer to TM-205, "
2WD : Removal and Installation".
Refer to GI-4, "
Components" for symbols in the figure.
JSDIA1856GB
Revision: 2010 May2011 QX56

TM-208
< UNIT REMOVAL AND INSTALLATION >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
4WD : Exploded View
INFOID:0000000006226910
4WD : Removal and InstallationINFOID:0000000006226911
REMOVAL
CAUTION:
 When removing the A/T assembly from engine, fi rst remove the crankshaft position sensor (POS)
from the A/T assembly.
 Be careful not to damage sensor edge.
1. Shift the selector lever to “P” pos ition, and release the parking brake.
2. Disconnect the battery cable from the negative terminal.
3. Remove control cable from A/T assembly. Refer to TM-178, "
Removal and Installation".
4. Disconnect heated oxygen sensor 2 connectors (bank 1 and bank 2). Refer to EX-5, "
Exploded View".
5. Remove exhaust front tube (RH and LH) and main muffler. Refer to EX-5, "
Exploded View".
6. Support A/T assembly with a transmission jack. CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug and
overflow plug.
7. Remove rear engine mounting cross member and engine mounting insulator (rear).
8. Separate propeller shaft assembly (front). Refer to DLN-129, "
Removal and Installation".
9. Separate propeller shaft assembly (rear). Refer to DLN-137, "
Removal and Installation".
10. Remove front under cover with a power tool. Refer to EXT-25, "
Removal and Installation".
11. Remove front suspension rear cross member.
1. A/T assembly 2. Front suspension rear cross mem- ber3. Rear engine mounting cross
member
4. Engine mounting insulator (rear)
A. Tightening must be done following the installation procedure. Refer to TM-208, "
4WD : Removal and Installation".
Refer to GI-4, "
Components" for symbols in the figure.
JPDIA1156GB
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-215
< UNIT DISASSEMBLY AND ASSEMBLY > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
16. Reverse brake piston 17. D-ring 18. D-ring
Refer to GI-4, "
Components" for symbols in the figure.
1. Parking rod 2. Manual plate 3. Manual shaft
4. Retaining pin 5. Detent spring 6. Oil seal
7. Bracket 8. O-ring 9. Self-sealing bolt
10. Baffle plate 11. O-ring 12. Seal ring
JSDIA1842GB
Revision: 2010 May2011 QX56

TM-238
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
vii. Remove parking gear (1) from output shaft (2).
viii. Remove seal rings (1) from output shaft.
43. Remove needle bearing from transmission case.
44. Remove output speed sensor
(1) from transmission case.
CAUTION:
 Never subject it to impact by dropping or hitting it.
 Never disassemble.
 Never allow metal filings, etc. to get on the sensor's front
edge magnetic area.
 Never place in an area affected by magnetism.
45. Remove reverse brake snap ring (fixing plate) with 2 flat-bladed screwdrivers.
CAUTION:
 Be careful not to scratch transmission case and reversebrake retaining plate.
 Be careful not to damage snap ring.
NOTE:
Press out snap ring from the transmission case oil pan side gap
with a flat-bladed screwdriver, and remove it using a another
screwdriver.
46. Remove reverse brake retaining plate from transmission case.
JPDIA0029ZZ
JPDIA0030ZZ
SCIA5031E
: Bolt
JSDIA1321ZZ
SCIA5032E
Revision: 2010 May2011 QX56