2011 INFINITI QX56 Starter

TM-78
< ECU DIAGNOSIS INFORMATION >[7AT: RE7R01B]
TCM
DTC Index
INFOID:0000000006226786
NOTE:
 If some DTCs are displayed at the same time, per form inspections one by one based on the priority as per
the following list. Refer to TM-77, "
DTC Inspection Priority Chart".
 The IGN counter is indicated in Freeze frame data (FFD). Refer to TM-61, "
CONSULT-III Function (TRANS-
MISSION)".
2P0615 STARTER RELAY
TM-104, "
DTC Logic"
P0705 T/M RANGE SWITCH ATM-106, "DTC Logic"
P0710 FLUID TEMP SENSOR ATM-107, "DTC Logic"
P0717 INPUT SPEED SENSOR ATM-109, "DTC Logic"
P0720 OUTPUT SPEED SENSOR TM-110, "DTC Logic"
P0740 TORQUE CONVERTERTM-128, "DTC Logic"
P0745 PC SOLENOID ATM-131, "DTC Logic"
P0750 SHIFT SOLENOID ATM-132, "DTC Logic"
P0775 PC SOLENOID BTM-133, "DTC Logic"
P0795 PC SOLENOID CTM-136, "DTC Logic"
P2713 PC SOLENOID DTM-147, "DTC Logic"
P2722 PC SOLENOID ETM-148, "DTC Logic"
P2731 PC SOLENOID FTM-149, "DTC Logic"
P2807 PC SOLENOID GTM-150, "DTC Logic"
3P0729 6GR INCORRECT RATIO
TM-114, "
DTC Logic"
P0730 INCORRECT GR RATIOTM-116, "DTC Logic"
P0731 1GR INCORRECT RATIOTM-118, "DTC Logic"
P0732 2GR INCORRECT RATIOTM-120, "DTC Logic"
P0733 3GR INCORRECT RATIOTM-122, "DTC Logic"
P0734 4GR INCORRECT RATIOTM-124, "DTC Logic"
P0735 5GR INCORRECT RATIOTM-126, "DTC Logic"
P0744 TORQUE CONVERTERTM-129, "DTC Logic"
P0780 SHIFTTM-134, "DTC Logic"
P1730 INTERLOCKTM-140, "DTC Logic"
P1734 7GR INCORRECT RATIOTM-142, "DTC Logic"
4U0300 CAN COMM DATA
TM-102, "
DTC Logic"
P0725 ENGINE SPEED TM-112, "DTC Logic"
P1705 TP SENSORTM-137, "DTC Logic"
P1721 VEHICLE SPEED SIGNALTM-138, "DTC Logic"
P1815 M-MODE SWITCHTM-144, "DTC Logic"
Priority Detected items (DTC) Reference
DTC*1
Items
(CONSULT-III screen terms) Reference
MIL*2, “ENGINE” with
CONSULT-III or GST CONSULT-III only
“TRANSMISSION”
— P0615 STARTER RELAY TM-104
P0705 P0705 T/M RANGE SWITCH A TM-106
P0710 P0710 FLUID TEMP SENSOR ATM-107
P0717 P0717 INPUT SPEED SENSOR ATM-109
P0720 P0720 OUTPUT SPEED SENSOR TM-110
Revision: 2010 May2011 QX56

TM-104
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0615 STARTER RELAY
P0615 STARTER RELAY
DescriptionINFOID:0000000006226801
TCM prohibits cranking other than at “P” or “N” position.
DTC LogicINFOID:0000000006226802
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Shift the selector lever to “P” and “N” positions.
2. Turn ignition switch ON and wait 2 seconds or more.
3. Perform “Self Diagnostic Results” in “TRANSMISSION”.
Is
“P0615” detected?
YES >> Go to TM-104, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226803
1.CHECK STARTER RELAY SIGNAL
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R connector terminal and ground.
Is the inspection result normal?
YES >> Check starter relay circuit. Refer to STR-7, "Wiring Diagram".
NO >> GO TO 2.
2. CHECK HARNESS BETWEEN A/T ASSEMBLY AND IPDM E/R (PART 1)
1. Turn ignition switch OFF.
2. Disconnect A/T assembly c onnector and IPDM E/R connector.
3. Check the continuity between A/T assembly vehi cle side harness connector terminal and IPDM E/R vehi-
cle side harness connector terminal.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0615 Starter Relay Circuit The starter monitor value is
OFF when the ignition switch is
ON at the “P” and “N” positions. Harness or connectors
(Starter relay and TCM circuit
is open or shorted.)
 Starter relay circuit
IPDM E/R connector
GroundCondition Voltage (Approx.)
Connector Terminal
E15 48 Selector lever in “P” and
“N” positions.
Battery voltage
Selector lever in other
positions. 0 V
Revision: 2010 May2011 QX56

P0615 STARTER RELAYTM-105
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3.CHECK HARNESS BETWEEN A/T ASSE MBLY AND IPDM E/R (PART 2)
Check the continuity between A/T assembly vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK JOINT CONNECTOR
1. Remove joint connector. Refer to TM-182, "
Exploded View".
2. Check the continuity between joint connector terminals.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace damaged parts.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
NO >> Repair or replace damaged parts.
A/T assembly vehicle side harness connector IPDM E/R vehicle side harness connector Continuity
Connector Terminal Connector Terminal
F51 9 E15 48 Existed
A/T assembly vehicle side harness connector GroundContinuity
Connector Terminal
F51 9 Not existed
A/T assembly harness connector side TCM harness connector side Continuity
Te r m i n a l Te r m i n a l
99Existed
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-165
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
SYSTEM SYMPTOM
Symptom TableINFOID:0000000006226890
 The diagnostics item numbers show the sequence for inspection. Inspect in order from item 1.
 Perform diagnoses of symptom table 1 before symptom table 2.
SYMPTOM TABLE 1
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Poor
perfor-
mance
Driving
perfor-
manceShift point is high in “D” position. 1 2 3
Shift point is low in “D” position. 1 2
Large
shock
When
shifting
gears →
“D” position4 7665 32 31
→ “R” position 4 7 6 6 5 3 2 1
1GR ⇔ 2GR 4 2544 3 1
2GR ⇔ 3GR 4 2544 3 1
3GR ⇔ 4GR 4 2544 3 3 1
4GR ⇔ 5GR 4 2544 3 3 1
5GR ⇔ 6GR 4 2544 33 1
6GR ⇔ 7GR 4 2544 3 3 1
Downshift when
accelerator ped-
al is depressed 3 2433 1
Upshift when ac-
celerator pedal
is released 3 2433 1
Lock-up 4 2444 3 1
Judder Lock-up 2 1 1 4 3
Strange noise In “R” position 2 1
In “N” position 2 1
In “D” position 2 1
Engine at idle 2 1
Revision: 2010 May2011 QX56

TM-166
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Func-
tion
trouble
Gear
does no
change “D” position Locks in 1GR 1 1 1 1
Locks in 2GR
Locks in 3GR
Locks in 4GR
Locks in 5GR 1
Locks in 6GR
Locks in 7GR
1GR
→ 2GR 1 1 1 1
2GR → 3GR 1
3GR → 4GR 2 22 2222 1
4GR → 5GR 1 1
5GR → 6GR 1
6GR → 7GR 1 1 1 1 1
5GR → 4GR 1
4GR → 3GR 1 1 1
3GR → 2GR 1 1
2GR → 1GR 1 1 1
Does not lock-up 2 22245 32222222 2 2 1
“M” posi-
tion 1GR
⇔ 2GR 3 33 32 3333333 3 3 1
2GR ⇔ 3GR 3 33 32 3333333 3 3 1
3GR ⇔ 4GR 3 33 32 3333333 3 3 1
4GR ⇔ 5GR 3 33 32 3333333 3 3 1
5GR ⇔ 6GR 3 33 32 3333333 3 3 1
6GR ⇔ 7GR 3 33 32 3333333 3 3 1
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-167
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Func-
tion trou-
ble
Poor
shiftingSlip
When
shifting
gears1GR
⇔ 2GR 3 3 3 4 2 2 1
2GR ⇔ 3GR 3 3 3 4 2 2 1
3GR ⇔ 4GR 3 3 3 4 2 2 2 2 1
4GR ⇔ 5GR 3 3 3 4 2 2 2 1
5GR ⇔ 6GR 3 3 3 4 2 2 2 1
6GR ⇔ 7GR 3 3 3 4 2 2 2 1
Engine
brake
does
not
work “D” position
→ “M” posi-
tion 5556423 33 1
“M” po-
sition 7GR
→ 6GR 5 5 5 6 4 2 3 3 3 1
6GR → 5GR 5 5 5 6 4 2 3 3 3 1
5GR → 4GR 5 5 5 6 4 2 3 3 3 1
4GR → 3GR 5 5 5 6 4 2 3 3 3 3 1
3GR → 2GR 5 556423 33 1
2GR → 1GR 5 5 5 6 4 2 3 3 3 1
Revision: 2010 May2011 QX56

TM-168
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
Func-
tion trou-
blePoor
power
trans-
mission
Slip With selector
lever in “D”
position, ac-
celeration is
extremely
poor.
53 334 2 2 2 1
With selector
lever in “R”
position, ac-
celeration is
extremely
poor. 53 334 2 2 2 1
While starting
off by acceler-
ating in 1GR,
engine races. 3 334 2 2 2 1
While acceler-
ating in 2GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 3GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 4GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 5GR,
engine races. 3 334 2 222 2 1
While acceler-
ating in 6GR,
engine races. 3 334 2 22221
While acceler-
ating in 7GR,
engine races. 3 334 2 2 22 2 1
Lock-up 3 334 2 2 1
No creep at
all. 111111111
Extremely
large creep. 1
Symptom
Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-169
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM TABLE 2
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Function
trouble
Power transmis-
sion cannot be
performed Vehicle cannot run in all
position.
3 2 111111111
Driving is not possible in
“D” position. 3 2 111111111
Driving is not possible in
“R” position. 32111
Engine stall 4 5 5 6 3 2 1
Engine stalls when selec-
tor lever shifted “N” → “D”
or “R”. 455 3 2 1
Engine does not start in
“N” or “P” position. 312 1
Engine starts in position
other than “N” or “P”. 32 1
Poor operation Vehicle does not enter
parking condition.
12
Parking condition is not
cancelled. 12
Vehicle runs with A/T in
“P” position. 12
Vehicle moves forward
with the “R” position. 12
Vehicle runs with A/T in
“N” position. 12
Vehicle moves backward
with the “D” position. 12
Revision: 2010 May2011 QX56