2011 INFINITI QX56 heater

FRONT SEATSE-107
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
PASSENGER SEAT
JMJIA4578GB
1. Headrest display 2. Headrest display escutcheon 3. Headrest trim
4. Headrest pad and frame 5. Headrest holder (locked) 6. Headrest holder (free)
7. Clip 8. Headrest display harness and upper tube9. Headrest display harness
10. Seatback board 11. Side air bag module 12. Seatback heater unit
13. Seat cushion lower inner finisher 14. Rear inner slide cover 15. Seat cushion lower outer finisher
Revision: 2010 May2011 QX56

SE-108
< REMOVAL AND INSTALLATION >
FRONT SEAT
CLIMATE CONTROLLED SEAT
16. Rear outer slide cover 17. Lumber support unit assembly 18. Seat harness
19. Seat cushion outer finisher inside (front) 20. Seat cushion outer finisher inside
(rear) 21. Seat cushion clip
22. Seat control switch cover 23. Seat control switch 24. Lumber support switch
25. Seat cushion outer finisher 26. Seat reclining switch knob 27. Seat slide and lifter switch knob
28. Seat cushion heater unit 29. Occupant detection system control unit30. Front outer slide cover
31. Front inner slide cover 32. Seat cushion front finisher 33. Seat cushion pad
34. Seat cushion trim 35. Seat cushion inner finisher 36. Seat cushion inner finisher inside (front)
37. Seat cushion inner finisher inside (rear) 38. Anchor bolt 39. Lap pre-tensioner
40. Foot welcome lamp 41. Seatback pad 42. Seatback trim
43. Seatback silencer 44. Headrest display harness lower tube 45. Seat frame assembly : Pawl
: Metal clip
Refer to GI-4, "
Components" for symbols in the figure.
Revision: 2010 May2011 QX56

FRONT SEATSE-115
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
3. Remove the headrest holder from the seatback while pressing the pawls as shown by the arrows in the figure.
CAUTION:
Before installing headrest holder check its orientation.
(Front/rear and right/left)
4. Disconnect the seatback heater unit harness connector (A). (with heater seat model only)
5. Remove the seatback pad and seatback trim. 1. Disconnect the foot welcome lamp harness connector and the harness clamp.
2. Remove the seatback retainer on the back side of the seatback.
3. Remove the side air bag harness clamp.
4. Remove the side air bag module mounting nuts.
5. Remove the headrest display harness lower tube (1) from
the seat frame assembly (2) while pressing up the pawls as
shown by the arrows in the figure.
6. Remove the seatback trim and the seatback pad from the seat frame assembly. Remove them
together with the headrest display harness lower tube and the side air bag module.
7. Remove the hog rings, and separate the seatback trim and seatback pad.
6. Remove the seatback silencer.
7. Remove the following parts after removing seatback silencer.  Seatback climate controlled seat unit (wit h climate controlled seat model only).
Refer to SE-117, "
CLIMATE CONTROLLED SEAT UNIT : Disassembly and Assembly".
 Remove the lumber support unit assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the pad side wire.
SEAT CUSHION
JMJIA4073ZZ
JMJIA4326ZZ
JMJIA3976ZZ
Revision: 2010 May2011 QX56

SE-116
< REMOVAL AND INSTALLATION >
FRONT SEAT
SEAT CUSHION : Disa ssembly and Assembly
INFOID:0000000006217426
DISASSEMBLY
1. Remove the seat cushion outer finisher.
1. Remove the metal clips and pawls, and then pull out seat
cushion outer finisher.
2. Disconnect the seat control switch, lumbar support switch harness connector.
2. Remove the seat cushion front finisher.
3. Remove the lap pre-tensioner. Refer to SB-8, "
SEAT BELT BUCKLE : Removal and Installation".
4. Remove the seat cushion inner finisher. 1. Remove the seat cushion inner finisher fixing screw (A).
2. Remove the metal clip and pawls then pull out seat cushioninner finisher.
5. Disconnect the seat cushion heater unit harness connector (A). (with heater seat model only)
6. Remove the seat cushion trim and seat cushion pad. 1. Remove the seat cushion retainer.
2. Remove the seat cushion trim and seat cu shion pad from the seat frame assembly.
3. Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
7. Remove the seat cushion finisher inside.  Remove the seat cushion inner finisher inside (front, rear).
 Remove the seat cushion outer finisher inside (front, rear).
8. Remove the following parts after removing seat cushion finisher inside.  Seat cushion climate controlled seat unit (with climate controlled seat model only).
Refer to SE-117, "
CLIMATE CONTROLLED SEAT UNIT : Disassembly and Assembly".
 Seat control unit (driver seat only).
Refer to ADP-135, "
Removal and Installation".
 Remove occupant detection system control unit. Refer to SR-30, "
Removal and Installation".
: Pawl
: Metal clip
JMJIA3966ZZ
: Pawl
: Metal clip
JMJIA3977ZZ
: Vehicle front
JMJIA4327ZZ
Revision: 2010 May2011 QX56

SECOND SEATSE-121
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
*: Heater seat model only.
BENCH SEAT (RH SEAT) AND CAPTAIN SEAT (RH SEAT)
1. Headrest LH 2. Headrest (center) 3. Headrest holder (free)
4. Headrest holder (locked) 5. Seatback heater unit
*6. Seatback trim
7. Seatback pad 8. Armrest outer cover 9. Armrest outer bracket
10. Bush 11. Armrest inner cover RH 12. Armrest trim
13. Armrest pad & frame 14. Armrest inner cover LH 15. Cup holder
16. Reclining inner cover (outside) 17. Seat inner hinge 18. Reclining device inner cover (out- side)
19. Reclining device inner cover (inside) 20. Seat cushion heater unit
*21. Seat cushion trim
22. Seat cushion pad 23. Seat hinge cover RH 24. Seat cushion hinge cover RH
25. Seat hinge cover LH 26. Seat cushion hinge cover LH 27. Seat cushion under cover
28. Seat harness assembly 29. Device arm cover 30. Reclining device outer cover (inside)
31. Reclining device outer cover (out- side) 32. Snap ring 33. Reclining lever knob
34. Anchor bolt 35. Seat belt buckle (center) 36. Seat belt buckle LH
37. Center seat belt retractor 38. Screw cap 39. Seatback center finisher
40. Seatback center finisher cover 41. Center seat belt shoulder guide 42. Seatback board
43. Seatback board clip 44. Center seat belt guide 45. Rear seat lever assembly
46. Seat control lever escutcheon 47. Seatback frame 48. Seat cushion frame
49. Seat hinge assembly RH 50. Seat cushion carpet RH 51. Seat hinge assembly LH
52. Seat cushion carpet LH : Pawl
Refer to GI-4, "
Components" for symbols in the figure.
Revision: 2010 May2011 QX56

SE-122
< REMOVAL AND INSTALLATION >
SECOND SEAT
1. Headrest RH 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seatback trim 5. Seatback pad 6. Seat cushion trim
7. Seat cushion pad 8.Seat cushion heater unit
*9. Seat cushion under cover
10. Seat cushion hinge cover RH 11. Seat hinge cover RH 12. Seat cushion hinge cover LH
13. Seat harness assembly 14. Seat cushion carpet 15. Seat belt buckle anchor bolt
16. Seat belt buckle 17. Reclining inner cover (outside) 18. Seatback frame
JMJIA4580GB
Revision: 2010 May2011 QX56

SECOND SEATSE-123
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
*: Heater seat model only.
CAPTAIN SEAT (LH SIDE)
19. Seat control lever escutcheon 20. Rear seat lever assembly 21. Seatback board
22. Seatback board clip 23. Seatback heater unit
*24. Reclining lever knob
25. Snap ring 26. Reclining device outer cover (out- side)27. Reclining device outer cover (inside)
28. Seat cushion frame 29. Seat hinge assembly RH 30. Seat hinge assembly LH : Pawl
Refer to GI-4, "
Components" for symbols in the figure.
Revision: 2010 May2011 QX56

SE-124
< REMOVAL AND INSTALLATION >
SECOND SEAT
1. Headrest 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seatback trim 5. Seatback pad 6. Seat cushion heater unit
7. Seat cushion trim 8. Seat cushion pad 9. Seat cushion under cover
10. Seat hinge assembly RH 11. Seat cushion hinge cover RH 12. Seat hinge cover LH
13. Seat cushion hinge cover LH 14. Seat hinge assembly LH 15. Seat harness assembly
16. Seat cushion carpet 17. Anchor bolt 18. Seat belt buckle
JMJIA4581GB
Revision: 2010 May2011 QX56