2011 HONDA CR-Z light

246
Maintenance
Maintenance Under the Hood Opening the Hood
Opening the Hood1. Park the vehicle on a level surface, and set the parking brake.Pull the hood release handle under the
2.
lower left corner of the dashboard.
The hood will pop up slightly.
3. Push up the hood latch lever in the center
of the hood to release the lock mechanism, and open the hood.
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
Hood Release Handle
Pull
Opening the Hood
NOTICE Do not open the hood when the wiper arms are raised.The hood will strike the wipers, and may damage either the hood or the wipers. When closing the hood, check that the hood is securely locked. If the hood latch lever moves stifly, or if you can open the hood without lifting the lever, the mechanism should be cleaned and lubricated. Do not open the hood while the auto idle stop function is activated.
Lever
Support Rod
Grip
Clamp
Main MenuTable of Contents

258
Maintenance
Replacing Light Bulbs
Headlight Bulbs
When replacing, use the following bulbs.
High beam headlight: 60W (HB3)
Low beam headlight: 55W (H11 for halogen bulb type)
35W (D4S for high voltage discharge)High Beam Headlight

■
1. Remove the cover.
2. Remove the coupler.
It can be removed by pushing the tab.
Rotate the old bulb to the left to remove.
3.
Insert a new bulb into the headlight
4.
assembly and turn it to the right.
Insert the coupler into the connector of the
5.
bulb.
Headlight Bulbs
NOTICE Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
NOTICE The headlight aim is set by the factory, and typically does not need to be adjusted. However, if you regularly carry heavy items in the cargo area, have the aiming readjusted by a dealer or another qualiied technician. The HB3 and H11 types are halogen bulbs. When replacing a bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. The exterior lights’ inside lenses (headlights, brake lights, etc.) may fog temporarily after a vehicle wash or while driving in the rain. This does not impact the exterior light function.However, if you see a large amount of water or ice accumulated inside the lenses, have your vehicle inspected by a dealer.
Cover
Bulb
TabCoupler
Main MenuTable of Contents

259
Maintenance
Replacing Light Bulbs Headlight Bulbs
Low Beam Headlights (High Voltage Discharge Type)
■*
Ask a dealer to inspect and replace low beam headlights.
Low Beam Headlights (Halogen Headlights)

■*
1. Remove the coupler.
It can be removed by pushing the tab.
Rotate the old bulb to the left to remove.
2.
Insert a new bulb into the headlight
3.
assembly and turn it to the right.
Insert the coupler into the connector of the
4.
bulb.Bulb
Tab
Coupler
*Not available on all models
Main MenuTable of Contents

260
Maintenance
Replacing Light Bulbs Fog Light Bulbs
Fog Light Bulbs* When replacing, use the following bulbs.
Fog Lights: 55W (H11)1. Turn the steering wheel all the way to the opposite side from the fog light being replaced. Passenger side: Turn the steering wheel
to the left. Driver side: Turn the steering wheel to
the right.Remove the clip and screws, and pull the
2.
inner fender back.
Fog Light Bulbs
NOTICE Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter. The fog lights are halogen bulbs. When replacing a bulb, handle it by its plastic case, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. When removing the clip, insert a lat-tip screwdriver, and lift and remove the central pin.
Clip
Inner Fender
Screw
*Not available on all models
Main MenuTable of Contents

261
Maintenance
Replacing Light Bulbs Fog Light Bulbs
3. Remove the coupler.
It can be removed by pushing the tab.
Rotate the old bulb to the left to remove.
4.
Insert a new bulb into the light assembly
5.
and turn it to the right.
Insert the coupler into the connector of the
6.
bulb.Bulb
Tab
Coupler
Fog Light Bulbs
When mounting the clip, insert while keeping the central pin of the clip raised, and push until the pin is lat.
Push until the pin is lat.
* Not available on all models
Main MenuTable of Contents

262
Maintenance
Replacing Light Bulbs Front Turn Signal/Parking/Side Marker Light Bulbs Side Turn Signal/Emergency Indicator Light Bulbs
Front Turn Signal/Parking/Side Marker Light Bulbs
When replacing, use the following bulbs.
Front Turn Signal/Parking/Side Marker: 28/8W1. Turn the socket to the left and remove it, then remove the old bulb.Insert a new bulb.
2.
Side Turn Signal/Emergency Indicator Light Bulbs Door mirrors have side turn signal lights. Have an authorized Honda dealer inspect and replace the light bulbs.
Main MenuTable of Contents

263
Maintenance
Replacing Light Bulbs Back-Up, Rear Turn Signal and Rear Side Marker Light Bulbs
Back-Up, Rear Turn Signal and Rear Side Marker Light Bulbs When replacing, use the following bulbs.
Back-Up: 16W Rear Turn Signal: 21W (Amber)Rear Side Marker: 3CP1. Pry on the edge of the cover using a flat-tip screwdriver to remove the cover.
Wrap the flat-tip screwdriver with a
cloth to prevent scratches.
2. Remove the bolts. Pull the light assembly out of the rear
3.
pillar.
Cover
continued
Main MenuTable of Contents

264
Maintenance
Replacing Light Bulbs Back-Up, Rear Turn Signal and Rear Side Marker Light Bulbs Brake/Taillight Bulbs
4. Turn the socket to the left and remove it, then remove the old bulb.Insert a new bulb.
5. 6. Reinstall the light assembly by sliding it on to the guide on the body.
Brake/Taillight Bulbs
Brake/rear taillight bulbs are LED type. Have an au thorized Honda dealer inspect and
replace the light bulbs.
Guide
Main MenuTable of Contents