2011 HONDA CR-Z light

265
Maintenance
Replacing Light Bulbs License Plate Light Bulbs High-Mount Brake Light Bulbs
License Plate Light Bulbs
When replacing, use the following bulbs.
License Plate Light: 5W1. Remove the lens by prying on the edge of the lens using a flat-tip screwdriver.
Wrap the flat-tip screwdriver with a
cloth to prevent scratches.
2. Remove the old bulb. Insert a new bulb.
3.
High-Mount Brake Light Bulbs High-mount brake light bulbs are LED type. Have an authorized Honda dealer inspect and replace the light bulbs.
Main MenuTable of Contents

287
Handling the Unexpected
If a Tire Goes Flat
Changing a Flat Tire
Changing a Flat Tire
Periodically check the tire pressure of the compact spare. It should be set to the speciied pressure.Speciied Pressure: 60 psi (420 kPa, 4.2 kgf/cm 2
)
When driving with the compact spare tire, keep the vehicle speed under 50 mph (80 km/h).Replace with a full size tire as soon as possible. The compact spare tire and wheel in your vehicle are speciically for this model.Do not use them with another vehicle.Do not use another type of compact spare tire or wheel with your vehicle. Do not mount tire chains on a compact spare tire. If a chain-mounted front tire goes lat, remove one of the full-size rear tires and replace it with the compact spare tire. Remove the lat front tire and replace it will the full size tire that was removed from the rear. Mount the tire chains on the front tire.
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually to reduce speed. Then, stop in a safe place. Replace the flat tire with the compact spare tire. Go to a dealer as soon as possible to have the full size tire repaired or replaced.
Park the vehicle on firm, level, and non-slippery ground.
1.
Put the shift lever in
2.
P (CVT).
Put the shift lever in
R (manual transmission).
Set the parking brake.
3.
Turn on the hazard warning lights and turn the ignition switch to LOCK
4.
0.
Main MenuTable of Contents

293
Handling the Unexpected
Engine Does Not Start
Checking the Engine If the engine does not start, turn the ignition switch to START
and check the
starter. Checking the Engine
If you must start the vehicle immediately, use an assisting vehicle to jump start it.
Jump Starting P.294
Starter Condition Check List
Starter will not start at all. Starter turns over very slowly.The 12 volt battery may be dead. Check each of the items on the right and respond accordingly. Check brightness of the interior light.Turn on interior lights and check brightness.
If the interior lights are dim or do not come on at all
•
12 Volt Battery Inspection and Maintenance P. 2 7 8
If the interior lights come on normally
•
Fuse Inspection and Replacement P. 3 0 4
The starter turns over normally but...There may be a problem with the fuse. Check each of the items on the right and respond accordingly. Review the engine start procedure.Follow its instructions, and try to start the engine again.
Staring the Engine
P.1 9 7
Check the immobilizer system indicator. When the immobilizer system indicator is blinking, the engine cannot be started.
Immobilizer System P.1 0 5
Check the fuel level. There should be enough fuel in the tank.
Fuel Gauge P.1 4
Check the fuse. Check all fuses, or have the vehicle checked by a dealer.
Inspecting and Changing Fuses P. 3 0 4
If the problem continues:
Emergency Towing P. 3 0 8
Main MenuTable of Contents

294
Handling the Unexpected
Jump Starting
Jump Starting Procedure
■
Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood.
1. Connect the first jumper cable to your vehicle’s battery
terminal.
Connect the other end of the first jumper
2.
cable to the assisting vehicle’s
terminal.
Use a 12 volt booster battery only.
Connect the second jumper cable to the
3.
assisting vehicle’s
terminal.
4. Connect the other end of the second jumper cable to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. If your vehicle is connected to another
5.
vehicle, start the assisting vehicle’s engine and increase its rpm slightly. Attempt to start your vehicle’s engine. If
6.
it turns over slowly, check that the jumper cables have good metal-to-metal contact.
Jump Starting
Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables. Battery performance degrades in cold conditions and may prevent the engine from starting.
WARNING
A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery.
Assisting
Vehicle’s Battery
Main MenuTable of Contents

297
Handling the Unexpected
Overheating
How to Handle Overheating Overheating symptoms are as follows:The high temperature indicator comes on or the engine suddenly loses power.
•
Steam is coming out of the engine compartment.
•
First Thing to Do
■
Immediately park the vehicle in a safe place.
1.
Put the shift lever to P (CVT) or N (manual transmission) and set the
parking brake. Turn off all accessories and turn on the hazard warning lights.
No steam coming out:
2. Keep the engine running and open the hood.
Steam coming out: Turn off the engine and wait until steam goes away.
Then, open the hood.
How to Handle Overheating
NOTICE Continuing to drive with the high temperature indicator on may damage the engine.
WARNING
Steam and spray from an overheated engine can seriously scald you. Do not open the hood if steam is coming out.
continued
Main MenuTable of Contents

299
Handling the Unexpected
Indicator, Coming On/Blinking
If the Low Oil Pressure Indicator Comes On
If the Low Oil Pressure Indicator Comes On
NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately.
■
Reasons for the Indicator to Come On
Comes on when the engine oil pressure is low.
What to Do as Soon as the Indicator Comes On
■
Immediately park the vehicle in a safe place.
1.
If necessary, turn the hazard warning lights on.
2.
What to Do After Parking the Vehicle
■
Stop the engine and let it sit for about one minute.
1.
Open the hood and check the oil level.
2.
Add oil as necessary.
Start the engine and check the low oil pressure indicator.
3.
The light goes out: Start driving again.
The light does not go out within 10 seconds: Stop the engine and
contact a dealer for repairs immediately.
Main MenuTable of Contents

302
Handling the Unexpected
Indicator, Coming On/Blinking If the Brake System Indicator Comes On If the EPS Indicator Comes On
If the Brake System Indicator Comes On
■Reasons for the Indicator to Come On
The brake fluid is low.

•
There is a malfunction in the brake system.

•
What to Do When the Indicator Comes On While Driving
■
Press the brake pedal lightly to check pedal pressure.
If normal, check the brake fluid level the next time you stop.

•
If abnormal, take immediate action. If necessary, downshift the

•
transmission to slow the vehicle using engine braking.
If the EPS Indicator Comes On
■Reasons for the Indicator to Come On
Comes on when there is a problem with EPS.

•
If you depress the accelerator pedal repeatedly to increase the

•
engine speed while the engine is idling, the indicator comes on, and sometimes the steering wheel becomes harder to operate.
What to Do When the Indicator Comes On
■
Stop the vehicle in a safe place and restart the engine.

• If the indicator comes on and stays on, immediately have your vehicle inspected by a dealer.
U.S.
Canada If the Brake System Indicator Comes On
Have your vehicle repaired immediately. It is dangerous to drive with low brake luid. If there is no resistance from the brake pedal, stop immediately in a safe place. If necessary downshift the gears. If the brake system indicator and ABS indicator come on simultaneously, the brake distribution system is not working. This can result in vehicle instability under sudden braking. Have your vehicle inspected by a dealer immediately.
If the EPS Indicator Comes On
NOTICE If the steering wheel is operated repeatedly or at an extremely low speed, or you hold the steering wheel on the full left or right position for a while, the system heats up. The system goes into a protective mode, and limits its performance. The steering wheel becomes harder and harder to operate. Once the system cools down, EPS is restored. Repeated operation under these conditions can eventually result in a damage to the system.
Main MenuTable of Contents

305
Handling the Unexpected
Fuses Fuse Locations
Interior Fuse Box
■
Located under the driver side dashboard.
Circuit Protected and Amps for Each Fuse
■
Fuse Locations
Fuse locations are shown on the label on the back side of the cover.
Locate the fuse in question by the fuse number and label number.
Label
Fuse BoxCover
Circuit Protected Amps
1 Back Up 15 A
2 TPMS* 1
7.5 A
3 Driver’s Power Window 20 A
4 - -
5 Back-Up Light 10 A
6 SRS 10 A
7 Transmission* 2
10 A
8 SRS 7.5 A
9 Fog Light* 20 A
10 A/C 7.5 A
11 ABS/VSA ®
7.5 A
12 IMA 10 ACircuit Protected Amps
13 Accessory Power Socket 20 A
14 Radio 7.5 A
15 Daytime Running Lights 7.5 A
16 Rear Wiper 10 A17 Passenger’s Power Window 20 A
18 - -
19 - -
20 Fuel Pump 15 A
21 Washer 15 A
22 Meter 7.5 A
23 Hazard 10 A
24 Stop/Horn 10 ACircuit Protected Amps
25 Audio AMP* 20 A
26 LAF 10 A
27 Door Lock Main 20 A
28 Headlight Main 20 A
29 Small Light 10 A
30 Main Fan Motor 30 A
31 IGPS 7.5 A
32 Right Headlight Low* 3
Right Headlight Low (HID)* 410 A 15 A
*1: U.S. models only *2: Automatic transmission (CVT)*3: Vehicle with halogen bulb low beam headlights*4: Vehicle with discharge headlights
continued
* Not available on all models
Main MenuTable of Contents