2011 HONDA CR-Z brake

246
Maintenance
Maintenance Under the Hood Opening the Hood
Opening the Hood1. Park the vehicle on a level surface, and set the parking brake.Pull the hood release handle under the
2.
lower left corner of the dashboard.
The hood will pop up slightly.
3. Push up the hood latch lever in the center
of the hood to release the lock mechanism, and open the hood.
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
Hood Release Handle
Pull
Opening the Hood
NOTICE Do not open the hood when the wiper arms are raised.The hood will strike the wipers, and may damage either the hood or the wipers. When closing the hood, check that the hood is securely locked. If the hood latch lever moves stifly, or if you can open the hood without lifting the lever, the mechanism should be cleaned and lubricated. Do not open the hood while the auto idle stop function is activated.
Lever
Support Rod
Grip
Clamp
Main MenuTable of Contents

256
Maintenance
Maintenance Under the Hood Brake/Clutch Fluid
Brake/Clutch Fluid
Specified fluid: Honda Heavy Duty Brake Fluid DOT 3
Use the same fluid for both the brakes and clutch.
Checking the Brake Fluid

■
The fluid level should be between the MIN and MAX marks on the side of the reservoir.
Checking the Clutch Fluid

■
The fluid level should be between the MIN and MAX marks on the side of the reservoir.
Brake/Clutch Fluid
If the speciied brake luid is not available, you
should use only DOT 3 or DOT 4 luid from a sealed container as a temporary replacement. Using any non-Honda brake luid can cause corrosion and decrease the longevity of the system. Have the brake system lushed and reilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.
NOTICE Brake luid marked DOT 5 is not compatible with your vehicle's braking system and can cause extensive damage. If the brake luid level is at or below the MIN mark, have the system inspected for leaks or worn brake pads by a dealer.
Brake Reservoir
MIN
MAX
Checking the Clutch Fluid
If the clutch luid level is at or below the MIN mark, have the system inspected for leaks or a worn clutch plate by a dealer.
Clutch Reservoir
MINMAX
Main MenuTable of Contents

258
Maintenance
Replacing Light Bulbs
Headlight Bulbs
When replacing, use the following bulbs.
High beam headlight: 60W (HB3)
Low beam headlight: 55W (H11 for halogen bulb type)
35W (D4S for high voltage discharge)High Beam Headlight

■
1. Remove the cover.
2. Remove the coupler.
It can be removed by pushing the tab.
Rotate the old bulb to the left to remove.
3.
Insert a new bulb into the headlight
4.
assembly and turn it to the right.
Insert the coupler into the connector of the
5.
bulb.
Headlight Bulbs
NOTICE Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
NOTICE The headlight aim is set by the factory, and typically does not need to be adjusted. However, if you regularly carry heavy items in the cargo area, have the aiming readjusted by a dealer or another qualiied technician. The HB3 and H11 types are halogen bulbs. When replacing a bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. The exterior lights’ inside lenses (headlights, brake lights, etc.) may fog temporarily after a vehicle wash or while driving in the rain. This does not impact the exterior light function.However, if you see a large amount of water or ice accumulated inside the lenses, have your vehicle inspected by a dealer.
Cover
Bulb
TabCoupler
Main MenuTable of Contents

264
Maintenance
Replacing Light Bulbs Back-Up, Rear Turn Signal and Rear Side Marker Light Bulbs Brake/Taillight Bulbs
4. Turn the socket to the left and remove it, then remove the old bulb.Insert a new bulb.
5. 6. Reinstall the light assembly by sliding it on to the guide on the body.
Brake/Taillight Bulbs
Brake/rear taillight bulbs are LED type. Have an au thorized Honda dealer inspect and
replace the light bulbs.
Guide
Main MenuTable of Contents

265
Maintenance
Replacing Light Bulbs License Plate Light Bulbs High-Mount Brake Light Bulbs
License Plate Light Bulbs
When replacing, use the following bulbs.
License Plate Light: 5W1. Remove the lens by prying on the edge of the lens using a flat-tip screwdriver.
Wrap the flat-tip screwdriver with a
cloth to prevent scratches.
2. Remove the old bulb. Insert a new bulb.
3.
High-Mount Brake Light Bulbs High-mount brake light bulbs are LED type. Have an authorized Honda dealer inspect and replace the light bulbs.
Main MenuTable of Contents

277
Maintenance
Checking and Maintaining Tires Winter Tires
Winter Tires If driving on snowy or frozen roads, mount all season marked “M + S” tires, snow tires, or tire chains; reduce speed; and maintain sufficient distance between vehicles when driving. Be particularly careful when operating the steering wheel or brakes to prevent skidding. Use tire chains, snow tires, or all season tires when necessary or according to the law. When mounting, refer to the following points. For winter tires:Select the size and load ranges that are the same as the original tires.
•
Mount the tires to all four wheels.
•
For tire chains: Install them on the front tires only. Because your vehicle has limited tire
•
clearance, Honda strongly recommends using the chains listed below:
Cable-type: SCC Radial Chain SC1030
Follow the chain manufacturer’s instruction when installing. Mount them as
•
tightly as you can. Check that the chains do not touch the brake lines or suspension.
•
Drive slowly.
•
Winter Tires
NOTICE Traction devices that are the wrong size or improperly installed can damage your vehicle's brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle. When tire chains are mounted, follow the chain manufacturer's instructions regarding vehicle operational limits.
WARNING
Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed. Follow all instructions in this owner’s manual regarding the selection and use of tire chains.
Main MenuTable of Contents

Handling the Unexpected
This chapter explains how to handle unexpected troubles.
285
Tools
Types of Tools ........................................ 286
If a Tire Goes Flat Changing a Flat Tire ............................... 287
Engine Does Not Start Checking the Engine .............................. 293
Jump Starting .......................................... 294
Shift Lever Does Not Move .................... 296
Overheating How to Handle Overheating ................... 297 Indicator, Coming On/Blinking
If the Low Oil Pressure Indicator
Comes On ............................................. 299If the Charging System Indicator
Comes On ............................................. 300If the Malfunction Indicator Lamp
Comes On or Blinks ............................... 301If the Brake System Indicator
Comes On ............................................. 302
If the EPS Indicator Comes On ................ 302
If the IMA Indicator Comes On ............... 303If the Low Tire Pressure/TPMS Indicator
Comes On or Blinks ................................ 303 Fuses
Fuse Locations ........................................ 304
Inspecting and Changing Fuses .............. 307
Emergency Towing ................................. 308
When You Cannot Open the Hatch ....... 310
Main Menu

287
Handling the Unexpected
If a Tire Goes Flat
Changing a Flat Tire
Changing a Flat Tire
Periodically check the tire pressure of the compact spare. It should be set to the speciied pressure.Speciied Pressure: 60 psi (420 kPa, 4.2 kgf/cm 2
)
When driving with the compact spare tire, keep the vehicle speed under 50 mph (80 km/h).Replace with a full size tire as soon as possible. The compact spare tire and wheel in your vehicle are speciically for this model.Do not use them with another vehicle.Do not use another type of compact spare tire or wheel with your vehicle. Do not mount tire chains on a compact spare tire. If a chain-mounted front tire goes lat, remove one of the full-size rear tires and replace it with the compact spare tire. Remove the lat front tire and replace it will the full size tire that was removed from the rear. Mount the tire chains on the front tire.
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually to reduce speed. Then, stop in a safe place. Replace the flat tire with the compact spare tire. Go to a dealer as soon as possible to have the full size tire repaired or replaced.
Park the vehicle on firm, level, and non-slippery ground.
1.
Put the shift lever in
2.
P (CVT).
Put the shift lever in
R (manual transmission).
Set the parking brake.
3.
Turn on the hazard warning lights and turn the ignition switch to LOCK
4.
0.
Main MenuTable of Contents