2011 Citroen DS3 Owner's Manual

47Monitoring





Monochrome screen C


Information displays



)
Press the button, located at the end of
the wiper stalk
, to display the various trip
computer tabs in succession.

- the current information tab
with:


●
the range,

●
the current fuel
consumption,

●
the distance remaining to
be travelled or the Stop &
Star t time counter.



- the trip "1"
tab with:


●
the distance travelled,

●
the average fuel
consumption,

●
the average speed,
for the first trip.



- the trip "2"
tab with:


●
the distance travelled,

●
the average fuel
consumption,

●
the average speed,
for the second trip.


)
Pressing the button again returns you to
the normal display.


16/9 colour screen (MyWay)


Trip zero reset



)
When the trip required is displayed, press
the button on the end of the wiper stalk for
more than two seconds.
Trips "1"
and "2"
are independent but their use
is identical.
For example, trip "1"
can be used for daily
figures, and trip "2"
for monthly figures.

A few definitions…


Range

(miles or km)
This indicates the distance
which can still be travelled with the fuel
remaining in the tank in relation to the average
fuel consumption over the last few miles
(kilometres) travelled.

Current fuel consumption

(mpg or l/100 km or km/l)

This is the average fuel consumption
during the last few seconds.

Average fuel
consumption
(mpg or l/100 km or km/l)
This is the average fuel consumption since the
last trip computer zero reset.


Average speed

(mph or km/h)
This is the average speed calculated
since the last trip computer zero reset
(ignition on).


Distance travelled

(miles or km)
This indicates the distance
travelled since the last trip computer zero reset.









Stop & Start time
counter
(minutes /sec onds or hour s /minutes)
If your vehicle is fitted with Stop & Start, a time
counter calculates the time spent in STOP
mode during a journey.
It resets to zero every time the ignition is
switched on with the key.
This value may vary following a change
in the style of driving or the relief,
resulting in a significant change in the
current fuel consumption.
If dashes are displayed continuously
while driving in place of the digits,
contact a CITROËN dealer or a
qualified workshop. This function is only displayed from
20 mph (30 km/h).
When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least
5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (100 km).


Distance remaining to
destination
(miles or km)
This is the distance remaining to be travelled
to the final destination. It can be entered by
the user.
If the distance is not entered, dashes are
displayed in place of the digits.

49Monitoring

002
Multifunction screens


Identify your multifunction screen in this section, to adjust or view vehicle
settings and information, by means of the user-friendly menus.

Monochrome screen A

This displays the following information:


- time,

- date,

- ambient temperature (this flashes if there is
a risk of ice),

- status of the doors and boot,

- audio sources (radio, CD...),

- trip computer (refer to the "Instruments and
Controls" section).
Warning messages (e.g.: "Emission control
system faulty") or information messages
(e.g.: "Boot open") may appear temporarily.
These can be cleared by pressing the "ESC"

button.


Displays on the screen

From the control panel of your Audio system,
you can:


)
press the "MENU"
button to gain access to
the main

menu
,

)
press the " 
" or " 
" buttons to scroll
through the items on the screen,

)
press the "MODE"
button to change
the permanent application (date, audio
source...),

)
press the " 
" or " 
" buttons to change a
setting value,

)
press the "OK"
button to confirm,
or

)
press the "ESC"
button to abandon the
operation in progress.



Controls



)
Press the "MENU"
button to gain access
to the main

menu
, then press the " 
" or
" 
" buttons to scroll through the various
menus:


- radio-CD,

- vehicle configuration,

- options,

- display settings,

- languages,

- units.

)
Press the "OK"
button to select the menu
required.


Main menu

53Multifunction screens

Radio-CD

With the Audio system switched on, once the
"Radio-CD" menu has been selected you can
activate or deactivate the functions linked
with use of the radio (RDS, REG), or the CD
(introscan, shuffle, CD repeat).
For more information on the "Radio- CD"
application, refer to the Audio system part of
the "Audio and Telematics" section.


Vehicle confi guration

Once the "Vehicle Configuration" menu has
been selected, you can activate or deactivate
the following equipment:


- wiper linked with reverse gear (refer to the
"Visibility" section),

- guide-me-home lighting (refer to the
"Visibility" section),

- parking sensors (refer to the "Driving"
section).



Options

Once the "Options" menu has been selected,
you can start diagnostics of the status of the
equipment (active, not active, faulty).

Languages

Once the "Languages" menu has been selected,
you can change the language used by the display
(Français, Italiano, Nederlands, Portugues,
Portugues-Brasil, Deutsch, English, Espanol).


Units

Once the "Units" menu has been selected,
you can change the units of the following
parameters:


- temperature (°C or °F),

- fuel consumption (l/100 km, mpg or km/l).
Once the fuel consumption units have
been set to mpg, the information in the
instrument panel screen on speed and
distance will also be in mph and miles. For safety reasons, configuration by the
driver of the multifunction screen must
only be done when stationary.


Display settings

Once the "Display settings" menu has been
selected, you can gain access to the following
settings:


- year,

- month,

- day,

- hour,

- minutes,

- 12 or 24 hour mode.

)
Once you have selected a setting, press
the " 
" or " 
" buttons to change its value.

)
Press the " 
" or " 
" buttons to switch
respectively to the previous or next setting.

)
Press the "OK"
button to save the change
and return to the normal display or press
the "ESC"
button to cancel.