2011 AUDI R8 SPYDER width

162 Cleaning and protection
Hand washing
When washing your vehicle by hand, first soft­
en the dirt with copious amounts of water and
rinse it
off as best you can.
Then clean the vehicle using a soft
sponge, an
auto glove or a low-pressure wash brush.
Work from the top down to the bottom, start­
ing with the convertible top
¢ page 163. Use
a
shampoo only for v ery stubborn dirt.
Rinse the sponge or auto glove thoroughly at
frequent intervals.
Clean the wheels, door sills and similar areas last. Use a separate sponge for this.
_& WARNING
-Car washes with conveyors can damage
the vehicle tires, which could cause the tire to lose pressure suddenly while driv­
ing and put you at risk for an accident.
Do not use car washes with conveyors.
- Switch
off the ignition when you wash
your vehicle to avoid an accident.
- Protect your hands and arms from sharp
metal edges when you clean the under­
body, the inside of the wheel wells or the
wheel covers to avoid cutting yourself.
- When washing your vehicle in the winter :
Moisture and ice in the brake system can
affect the brakes.
- Never wash tires with a jet that sprays
water in a direct stream . This could cause
invisible damage to the tires and weaken
them, even if the spray is from a relative ­
ly long distance and for a short time .
Damaged and weakened tires can fail
and cause accidents and personal injury.
(D Note
- Never drive your vehicle through any au ­
tomatic car wash that fails to provide ei­
ther sufficient clearance for your vehicle
or sufficient track width for your tires. Risk of expensive damage to the vehicle's
underbody , tires, and rims!
- As described in your Warranty
& Mainte­
nance booklet, damage or malfunction due to misuse of the vehicle or failure to
operate the vehicle in accordance with
the
instructions of this Owner's Manual
will not be covered under warranty.
- Fold the exterior mirrors flat - there is a
risk of damaging the exterior mirrors .
Power folding exterior mirrors must not
be folded in or out by hand. Use the pow­
er function!
- Do not wash the vehicle in direct sun­
light. You may damage the paint.
- Do not use sponges designed to remove
insects, rough kitchen sponges, or simi­
lar products. You risk damaging the
paint surface.
- You should remove debris (such as in­
sects) from the headlight lenses on a
regular basis, for example when refuel­
ing your vehicle. Never clean the head­
lights with a dry cloth or sponge . Use a
wet cloth or sponge .
It is best to use
soapy water.
- Never clean tires using a nozzle that
sprays water in a direct stream. Damage
can occur even with a relatively long
spraying distance and for a very short
time.
- To avoid damaging your vehicle, always
make sure that there is sufficient dis­
tance between the spray head and soft materials like rubber hoses, plastic parts
and sound-deadening materials. Never
aim the spray head at the same point for
a long time. This also applies to cleaning
headlights and painted bumpers. Re­
member: the closer the nozzle is to the
surface of the material, the greater the
stress on the material.
- Never clean the convertible top using a
power washer.
@) For the sake of the environment
Wash your vehicle only at specially de­
signed facilities. They can prevent any dirty
water contaminated by oil from entering
the waste water. In certain areas washing
a car outside of such facilities is not per­
mitted.

Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Maximum (permissible) inflation pressure
means the maximum cold inflation pressure
to which a tire may be inflated. Also called
"maximum inflation pressu re."
Normal occupant weight
means 150 lbs. (68 k ilograms) times the
nu mber of occupants seated in the vehicle up
to the total seating capacity of your vehicle.
Occupant distribution
means distribution of occupants in a vehicle .
Outer diameter
means the overa ll diameter of an inflated new
tire.
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ­
ing e levations due to labeling, decorations, or
protective bands or ribs.
Ply
means a layer of rubber-coated para llel cords.
Production options weight
means the comb ined weight of those installed
regular production options weighing over 5
lbs . (2 .3 kg) in excess of those standard items
which they replace, not previously considered
in curb weight or accessory weight, including
heavy duty brakes, r ide leve lers, roof rack,
heavy duty battery, and specia l trim .
Radial ply tire
means a pneumatic t ire in which the p ly cords
that extend to the beads are laid at substan­
tially 90 degrees to the centerline of the
tread.
Tires and wheels 191
Recommended inflation pressure
see ~ page 190, Cold tire inflation pressure.
Reinforced tire
means a t ire designed to operate at higher
loads and at higher inflat ion pressures than
the corresponding standard tire. Re inforced
ti res my be ident ified as "XL" , "xl", "E XTRA
LOAD", or "RF" on the sidewall.
Rim
means a metal support for a tire or a tire and
tube assembly upon which the tire beads are
seated.
Rim diameter
means nom inal d iameter of the bead seat. If
you change your wheel s ize, you w ill have to
purchase new tires to match the new r im di­
ameter.
Rim size designation
means r im diameter and width.
Rim width
means nom inal distance between rim fla nges.
Sidewall
means that portion of a tire between the
tread and bead.
Speed rating (letter code)
means the speed at which a tire is designed to
be driven for extended periods of time. The
ratings range from 93 mph (150 km/h) to
186 mph (298 km/h)
~ page 200 . You may
not find this information on all tires because
it is not requ ired by law.
T he speed rating letter code, where applica­
ble, is molded on the tire sidewall and indi­
cates the maximum pe rm issib le road speeds
~ .&. in Winter tires on page 204.
Tire pressure monitoring system
means a system that detects when one or
more of a veh icle's tires are underinflated and
illuminates a low tire pressure warning tell­
tale.
•
•

A WARNING
Sudden tire failure can lead to loss of con­
trol, a crash and serious personal injury!
- Never drive a vehicle when the tread on
any tire is worn down to the wear indica­
tors.
- Worn tires are a safety hazard, they do
not grip well on wet roads and increase
your risk of "hydroplaning" and loss of
control.
- Always keep chemicals that can cause
tire damage, such as grease, oil, gasoline
and brake fluid away from t ires.
- Tires age even if they are not be ing used
and can fail suddenly, especially at high
speeds . Tir es that are more than 6 years
old can only be used in an emergency
and then with special care and at lower
speeds.
- Never mount used tires on your vehicle if
you are not sure of their" previous histo ­
ry ." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden tire failure
and loss of vehicle control.
Tires and wheels 199
New tires and replacing tires and wheels
New tires and wheels have to be broken in .
Fig. 153 Tir e specificat ion codes on t he s idewall o f a
tire
No. Description
CD Passenger car tire (where applicable)
@ Nominal w idth of tire in millimeters
® Ratio of height to width (aspect ratio)
© Radial
® Rim diameter code
® Load index and speed rating
(f) U.S. DOT tire identification number
® Audi Origina l tire
® Severe snow conditions
@ T ire ply composition and materials
used
@ Maximum load rating
@ Treadwear, traction and temperature
grades
@ Maximum permissible inflation pres-
sure
The tires and rims are essential parts of the
vehicle's design . The tires and rims approved
by Audi are spec ially matched to the charac­
teristics of the vehicle and can make a major .,.
•

200 Tires and wheels
contribution to good road holding and safe
handling when in good condition and properly
inflated
¢ ,& .
We recommend that all work on tires and
wheels be performed by an authorized Audi
dealer. They are familiar with recommended
procedures and have the necessary special
tools and spare parts as well as the proper fa­
cilities for disposing of the old tires.
Authorized Audi dealers have the necessary
information about technical requirements for
installing or changing tires and rims.
Replacing tires and wheels
Tires should be replaced at least in pairs and
not individually (for example both front tires
or both rear tires together).
Be sure to read and heed the information to
the tire pressure monitoring system
¢page 201.
Always buy replacement radial tires that have
the same specifications as the tires approved
for your vehicle by Audi. Replacement tires
must always have the same load rating speci­
fication as the original equipment or approved optional tires listed in the table
¢page 193.
Audi-approved specification tires are specially
matched to your vehicle and its load limits,
and can contribute to the important road hold­
ing, driving characteristics, and safety of the
vehicle. The table(¢
page 193) lists specifica­
tions of the tires approved for the Audi mod­
els covered by your Owner's Literature .
The tire pressure label located on driver's side
B-pillar (
¢ page 193, fig. 151) lists the speci­
f ications of the original equipment tires in­
stalled on your vehicle at the time it was man­
ufactured.
Federal law requires tire manufacturers to
place standardized information on the side­
wall of all tires¢
fig. 153. This information
identifies and describes the fundamental
characteristics, the quality grade of the tire
and also provides a tire identification number for
safety standard certification and in case of
a recall.
Tire specifications
Knowledge of tire specifications makes it eas­
ier to choose the correct tires. Radial tires
have the tire specifications marked on the
sidewall, for example:
P235 / 35 R 18 91 Y
This contains the following information:
P Indicates the tire is for passenger cars
235 Nominal tire width in mm of the tire
from sidewall edge to sidewall edge. In general, the larger the number, the wider
the tire
35 Height/width ratio in percent (aspect ra-
tio)
R Tire construction: Radial
18 Rim diameter code (in inches)
91 Load rating code
Y Speed rating letter code
XL (or "xl", "EXTRA LOAD", or "RF") indicates
that the tire is a"Reinforced" or an "Extra
Load" tire
M+S (or "M/S") Indicates that the tire has
some mud and snow capability
The tires could also have the information of
direction of rotation¢
page 189.
Tire manufacturing date
The manufacturing date is also indicated on
the tire sidewall (possibly only on the
inner
side of the wheel):
"DOT ... 2210 ... " means, for example, that
the tire was produced in the 22nd week of 2010.
Speed rating (letter code)
The speed rating letter code on the wheels in­
dicates the maximum permissible road speeds
¢ .&. in Winter tires on page 204.
P up to 93 mph (150 km/h)
Q up to 99 mph (158 km/h)
R up to 106 mph (170 km/h)
S up to 110 mph (180 km/h)

206 Tires and wheels
conditions. Ask your authorized Audi dea ler
for more details.
The low aspect ratio of these tires is indicated
by a numeral of
55 or less in the tire's size
designation. The numeral represents the ratio
of the tire's sidewall height in relation to its
tread width expressed in percentage. Conven­
tional tires have a height/width ratio of 60 or
more.
The performance of low-aspect -ratio tires is
particularly sensitive to improper inflation
pressure. It is therefore important that low
aspect ratio tires are inflated to the specified pressure and that the inflation pressure is reg ­
ularly checked and mainta ined. Tire pressures
should be checked at least once a month and
a lways before a long t rip
~ page 195, Check­
ing tire pressure.
What you can do to avoid tire and rim
damage
L ow aspect ratio tires can be damaged more
eas ily by impact with potholes, curbs, gullies
or ridge5 on the road, particu larly if the tire i5
underinflated.
I n order to minimize the occurrence of impact
damage to the tires of your vehicle, we recom­
mend that you observe the following precau­
tions:
- Always maintain recommended inflation
pressures. Check your tire pressure every
2.000 miles (3.000 km) and add air if neces­
sary.
- Drive carefully on roads with potholes, deep
gullies or ridges. The impact from driving
through or over such obstacles can damage
your tires. Impact with a curb may also cause damage to your tires.
- After any impact, immediately inspect your
tires or have them inspected by the nearest
authori zed Audi dealer. Rep lace a damaged
tire as soon as possible.
- Inspect your tires every 2.000 miles (3.000 km) for damage and wear . Damage is not al­
ways easy to see. Damage can lead to loss of
air and underinflation, wh ich could eventu ­
ally cause t ire failure . If you believe that a tire
may have been damaged, replace the
tire as soon as possib le.
- These tires may wear more quickly than oth­
ers.
- Please also remember that, while these tires
deliver responsive handling, they may ride
less comfortably and make more noise than
other choices .
Reduced performance in winter/cold
season conditions
All tires are designed for certain purposes.
The low aspect ratio, ultra high performance
t ir es originally installed on your vehicle are in­
tended for maximum dry and wet road per­
formance and handling . They are not suitable
for cold, snowy or icy weather conditions . If
you drive under those c ircumstances, you
should equ ip your vehicle w ith winter t ires,
which offer better traction under those condi­
tions . We suggest yo u use the recommended
snow tires specified for your vehicle, or their
equivalent.
Refer to~
poge 203 for more detailed infor­
mation regarding winter tires.
Ti re pressure
monitoring system
General notes
E ach tire, including the spare (if provided),
shou ld be checked monthly when cold and in­
flated to the inflat ion pressure recommended
by the vehic le manufacturer on the vehicle
placard or tire inflation pressure label (If your
vehicle has tires of a different si ze than the
size indicated on the vehicle placard or tire in­
flat ion pressure label, you should determine
the proper t ire in flation pressure for those
t ir es .) .
As an added safety feature, your vehicle has been equipped with a tire pressure monitoring
system (TPMS) that illum inates a low tire
pressure telltale when one or more of your
tires is significantly under-inflated. According­
ly, when the low tire pressure telltale illumi­
nates, you shou ld stop and check you r tires as
Ill>-

Dimensions
!Length (with license plate bracket)
Width
Width (across mirrors)
Height (unloaded)
T urning circle diameter (curb to curb) R8 Sp
yd er 4. 2
quattro
4434 mm (ap­ prox. 174.6 in)
1904 mm (approx . 75 .0
in)
2029 mm (ap­ prox. 80.0 in)
1244 mm (ap­
prox. 49.3 in)
11.80
m (ap­
prox. 3 8. 7
ft)
When driving up steep ramps, on rough roads,
over curbs, etc. it is important to remembe r
that some parts of your vehicle, such as spoil­
ers or exhaust system components, may be
close to the ground . Be careful not to damage
them.
This applies especially to vehicles with a low chassis (sports chassis) and when the vehicle
is fully loaded .
Capacities (approx.)
Fuel tank
R8 R8
Spyder Spyder
4 .2 5.2
quattro quat -
tro
Total capacity gal/ 21.1/8 21.1/8
liters 0 0
Reserve (of total gal/ 2.6/10 2 .6/10
capacity) liters
Windshield wa she r sys tem
Windsh ield wash- quarts approx. 4.2/4.0
er fluid /liters
D ata 229
R8 Spyder 5.2
qu attro
4434 mm (ap­ prox. 174.6 in)
1904 mm (approx. 75.0 in)
2029 mm (approx. 79.9 in)
1
1244 mm (approx. 49.0 in)
11.80 m (approx. 38. 7
ft)
•
•