2011 Acura TSX ignition

Operating the Switches Around the Steering Wheel
Light Switches
106Controls
Automatic Operation (automatic lighting control)
Automatic lighting control can be used when
the ignition switch is in ON
II
.
When you turn the light switch to
AUTO
,
the headlights and other exterior lights will
switch on and off automatically depending
on the ambient brightness.
Automatic Operation (automatic lighting control)
We recommend that you turn on the lights manually
when driving at night, in a dense fog, or in dark
areas such as long tunnels or parking facilities.
The light sensor is in the location shown below.
Do not cover this light sensor with anything;
otherwise, the automatic lighting system may not
work properly.Light SensorYou can change the AUTO light sensitivity and
automatic lighting off timer setting using the multi-
information display.
Customization Procedure


P. 8 0
Automatic lighting off feature
The headlights, all other exterior lights, and the instrument panel lights turn off
within 15 seconds after you remove the key and close the driver's door.
If you turn the ignition switch to LOCK
0 with the headlight switch on, but do
not open the door, the lights turn off after 10 minutes (3 minutes, if the switch is
in the
AUTO
position).
The lights turn on again when you unlock or open the driver's door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver's door, you will hear a lights on reminder chime.

Operating the Switches Around the Steering Wheel
Fog Lights
107
Controls
Fog Lights
When the low beam headlights are on, turn
the fog light switch on to use the fog lights.
Fog Lights
When the fog lights are on, the indicator in the
instrument panel will be on.
They go off when the headlights turn off, or when
the daytime running lights are on.
Indicators


P. 6 4
Daytime Running LightsThe high beam headlights and indicator come on slightly dimmer than normal.
The ignition switch is in ON t
II
.
The headlight switch is off, or in t
.
The parking brake is released. t
The lights remain on even if you set the parking brake. Turning off the ignition
switch will turn off the daytime running lights.
The high beam headlights return to the original brightness once the headlight
switch is turned on.
Fog Light Switch

Operating the Switches Around the Steering Wheel
Wipers and Washers
108Controls
Wipers and Washers
The windshield wipers and washers can be
used when the ignition switch is in ON
II
.
MIST
The wipers run at high speed until you
release the lever. Wiper switch (OFF, INT, LO, HI)
Change the wiper switch setting according to
the amount of rain. Adjusting the delay
Turn the adjustment ring to adjust the wiper
delay.
Windshield Wipers and Washers NOTICE Do not use the wipers when the windshield is dry.
The windshield will get scratched, or the rubber
blades will get damaged. NOTICE In cold weather, the blades may freeze to the
windshield, becoming stuck.
Operating the wipers in this condition may
damage the wipers. Use the defroster to warm the
windshield, then turn the wipers on.
If the vehicle speeds up while the wipers are
operating intermittently, the length of the wipe
interval shortens. When the vehicle starts moving,
the wipers make a single sweep.
The wiper operation of the shortest delay setting
(
) and the LO setting become the same when the
vehicle speeds up.
Turn the washers off if no washer fluid comes out.
The pump may get damaged.
Long delayShort delay
Washer
Sprays while you pull the lever toward you.
When you release the lever, the wipers make
two or three more sweeps before stopping.
MIST OFF INT: Low speed with
intermittent LO: Low speed wipe HI: High speed wipe Intermittent Time
Adjustment RingPull
to use
washer.

Operating the Switches Around the Steering Wheel
Brightness Control
109
Controls
Brightness Control
When the parking lights are turned on and
the ignition switch is in ON
II
, you can
use the brightness control knob to adjust
instrument panel brightness.
Brighten: Turn the knob to the right.
Dim: Turn the knob to the left.
You will hear the beeper when the brightness
reaches minimum or maximum. The multi-
information display will return to its original
state several seconds after you adjust the
brightness.
Brightness level indicator
The brightness level is shown on the multi-
information display while you are adjusting it.
As the brightness level increases to the right,
the instrument panel gets brighter.
Brightness Control
Instrument panel brightness varies, depending
on whether the exterior lights are on or off. The
instrument panel dims to reduce glare when they
are on.
Pressing either
(information) button
switches the display.
If you turn the knob to the right until the brightness
display is up to max, the beeper sounds. This cancels
the reduced instrument panel brightness when the
parking lights are on.
The brightness can be set differently for when the
exterior lights are on, and when they are off.
Control Knob

Operating the Switches Around the Steering Wheel
Rear Defogger/Heated Door Mirror Button
110Controls
Rear Defogger/Heated Door Mirror Button
Press the rear defogger and heated door
mirror button to defog the rear window and
mirrors when the ignition is in ON
II
.
The rear defogger and heated door mirrors
automatically switch off after 10-30 minutes
depending on the outside temperature.
However, if the outside temperature is 32°F
(0°C) or below, they do not automatically
switch off.
Rear Defogger/Heated Door Mirror Button NOTICE When cleaning the inside of the rear window, be
careful not to damage the heating wires.
It is critical to wipe the window from side to side
along the defogger heating wires.
This system consumes a lot of power, so turn it off
when the window has been defogged.
Also, do not use the system for a long period when
the engine is idling. This may weaken the battery,
making it difficult to start the engine.

Operating the Switches Around the Steering Wheel
Driving Position Memory System*
112Controls
1. Adjust the driver's seat to the desired
position, and turn the ignition switch to
ON
II
.
2. Press the SET button.
You will hear the beeper, and the
memory button indicator light will blink.
3. Press memory button
1
or
2
within five
seconds of pressing the SET button.
Once the seat position has been
memorized, the indicator light on the
button you pressed stays on.
Storing a Position in Memory
Automatic transmission models 1. Move the shift lever to
P
.
All models 2. Apply the parking brake.
3. Press a memory button (
1
or
2
).
You will hear the beeper, and the
indicator light will blink.
The seat will automatically move to the
memorized position. When it has finished
moving, you will hear the beeper, and the
indicator light stays on.
Recalling the Stored Position
Storing a Position in Memory
After you press the SET button, the storing
operation will be canceled when:
You do not press the memory button within five tseconds.
You readjust the seat position before the double- tbeep.
You turn the ignition switch to any position texcept ON
II.
Recalling the Stored Position
The seat will stop moving if you:
Press the SET button, or a memory button ( t
1 or
2).
Adjust the seat position.
t Automatic transmission models Shift into any position except t
P.
Manual transmission models Release the parking brake. t
Memory Button 1
Memory Button 2
Set ButtonMemory Buttons

Adjusting the Mirror
114Controls
Interior Rearview MirrorAdjust the angle of the rearview mirror when you are sitting in the correct driving
position.
When driving after dark, the automatic
dimming rearview mirror reduces the glare
from headlights behind you. Press the AUTO
button to turn this function on and off.
When activated, the AUTO indicator comes
on.
Adjusting the Mirror
Keep the inside and outside mirrors clean and
adjusted for best visibility.
Adjust the mirrors before you start driving.
Adjusting the Seat Positions


P. 11 6
Automatic Dimming Rearview Mirror
The auto dimming function cancels when the shift
position is in R.
Automatic Dimming Rearview Mirror
You can adjust the door mirrors when the
ignition switch is in ON
II
.
Mirror position adjustment
L/R selector switch: Select the left or right
mirror. After adjusting the mirror, return the
switch to the center position.
Mirror position adjustment switch: Press
the switch left, right, up, or down to move
the mirror.
Door Mirrors
Indicator Sensor
Auto Button
Adjustment Switch
Selector Switch

Adjusting the Mirror
Door Mirrors
115
Controls
Reverse Tilt Door Mirror
If activated, the passenger side door mirror
automatically tilts downward when you put
the shift lever in
R
; this improves close-in
visibility on the passenger side of the vehicle
when backing up. The mirror automatically
returns to its original position when you shift
out of
R
.
To activate this feature, turn the ignition
switch to ON
II
and slide the selector switch
to the passenger’s side.
Selector Switch