2011 Acura TSX ignition

180Features
Compass
*
Compass Zone Selection
Zone Number
1. Turn the ignition switch to ON
II
.
2. Press and hold the MENU button until the
display shows the compass setting menu
list.
3. Rotate
to select ZONE, then press

. The display shows the current zone
number.
4. Rotate
to select the zone number of
your area (See Zone Map), then press
.
Compass Zone Selection
Compass Zone Selection
The zone selection is done to compensate the
variation between magnetic north and true north.
If the calibration starts while the audio system
is in use, the display returns to normal after the
calibration is completed.
Zone Map
1
2
3
4
5
6
7891011121314 15
Guam Island : Zone 8
Puerto Rico : Zone 11

192Driving
When Driving
Starting the Engine
3. Turn the ignition switch to START III

without depressing the accelerator pedal.
Starting the Engine
Do not hold the key in START
III
for more than 15
seconds.
If the engine does not start right away, wait for at
tleast 10 seconds before trying again.
If the engine starts, but then immediately stops, twait at least 10 seconds before repeating step 3
while gently depressing the accelerator pedal.
Release the accelerator pedal once the engine
starts.
The immobilizer system protects your vehicle from
theft. If an improperly coded key (or other device) is
used, the engine's fuel system is disabled
Immobilizer System


P. 9 8
Starting to Drive
Automatic transmission models 1. Keeping your right foot on the brake pedal, release the parking brake. Check
that the brake system indicator has gone off.
Parking Brake

P. 2 1 0
2. Put the shift lever in D
. Select R
when reversing.
3. Gradually release the brake pedal and gently depress the accelerator pedal to
pull away.

193
Driving
When Driving
Precautions While Driving
Precautions While Driving
In Rain
Avoid driving in deep water and on flooded roads. This can damage the engine or
cause electrical component failure.
Other Precautions
If there is a strong impact with something under the vehicle, stop in a safe
location. Check the underside of the vehicle for damage any fluid leaks.
Precautions While Driving NOTICE Do not operate the shift lever while pressing
the accelerator pedal. You could damage the
transmission.
If the ignition switch is turned to ACCESSORY
I or
LOCK
0 while driving, the engine will shut down
and all steering and brake power assist functions
will stop, making it difficult to control the vehicle.
Do not put the shift lever in
N
, as you will lose
engine braking (and acceleration) performance.
During the first 600 miles (1,000 km) of operation,
avoid sudden acceleration or full throttle operation
so as to not damage the engine or powertrain.
Avoid hard braking for the first 200 miles (300 km).
You should also follow this when the brakes are
replaced.

195
Continued
Driving
When Driving
Shifting
Change the shift position in accordance with your driving need.
Shift lever positions
Shifting
You cannot turn the ignition switch to LOCK
0 and
remove the key unless the shift lever is in
P.
The vehicle may move forward very slightly even in
N
while the engine is cold.
Depress the brake pedal firmly and, when necessary,
apply the parking brake.
Auomatic transmission models Shifting
Park
Used when parking or starting the
engine
Reverse
Used when backing up
Neutral
Used when idling
Drive
Used for:
Normal driving (gears change t
between 1st and 5th automatically)
Temporarily driving in the sequential t
mode
Drive (S)
Used for:
Automatically changing gears t
between 1st and 4th (4th gear is
used only at high speed)
Driving in the sequential mode t
P
R
N
D
S

200Driving
When Driving
Shifting
Reverse Lockout
The manual transmission has a lockout mechanism that stops you from accidentally
shifting into
R
from a forward gear while the vehicle is moving at a certain
speed.
If you cannot shift to
R
when the vehicle is stopped, do the following:
1. Depress the clutch pedal, move the shift
lever all the way to the left, and shift
to
R
.
2. If you still cannot shift into
R
, apply the
parking brake, and turn the ignition switch
to ACCESSORY
I or LOCK
0
.
3. Depress the clutch pedal and shift into
R
.
4. Keep depressing the clutch pedal and start
the engine.
Have the vehicle checked by a dealer if you
have to go through this procedure repeatedly.

201
Continued
Driving
When Driving
Cruise Control
Cruise Control

Maintains a constant vehicle speed without having to keep your foot on the
accelerator. Use cruise control on freeways or open roads where you can travel at
a constant speed with little acceleration or deceleration.
Cruise Control
When the ignition switch is in ACCESSORY
I or
LOCK
0, cruise control automatically goes off.
It may not be possible to maintain a constant speed
when driving uphill or downhill.
Always keep sufficient distance
between you and the vehicle in
front of you.
CRUISE MAIN is on in the
instrument panelCruise control is ready to use.
OVehicle speed for cruise control:
Desired speed in a range above
roughly 25 mph (40 km/h) ~ Automatic transmission models OShift positions for cruise control:
In
D
or
S, in 2nd gear or higher
OPress the
CRUISE
button on
the steering wheel
How to use
WARNING
Improper use of the cruise control can
lead to a crash.
Use the cruise control only when traveling
on open highways in good weather.
When to use

206Driving
When Driving
TPMS (Tire Pressure Monitoring System)
TPMS (Tire Pressure Monitoring System)Monitors the tire pressure while you are driving. If your vehicle's tire pressure
becomes significantly low, the low tire pressure/ TPMS indicator comes on and a
message appears on the multi-information display.
TPMS (Tire Pressure Monitoring System)
Conditions such as low ambient temperature and
altitude change directly affect tire pressure and
can trigger the low tire pressure/ TPMS indicator to
come on.
If the Low Tire Pressure/TPMS Indicator

Comes On or Blinks P. 2 9 3
To select the tire pressure monitor, turn
the ignition switch to ON
II
and press the
(information) button until you see
the tire pressure screen.
If all the tire pressures are normal, "TIRE
PRESSURE OK" will be displayed.
Tire Pressure Monitor
To display the pressure of all four tires, press
the SEL /RESET button.
The pressure for each tire is displayed in PSI
(U.S.) or kPa (Canada).
Tire Pressure Monitor
The pressure displayed on the multi-information
display can be slightly different from the actual
pressure as measured by a gauge. If there is a
significant difference between the two values, or
if the low tire pressure/ TPMS indicator and the
message on the multi-information display do not go
off after you have inflated the tire to the specified
pressure, have the system checked by a dealer.
"SYSTEM FUNCTION ERROR" may appear if you
drive with the compact spare tire, or there is a
problem with the TPMS.

225
Continued
Maintenance
If the engine oil life is less than 15%, you will see the Maintenance Minder
messages appear on the multi-information display every time you turn the ignition
switch to ON
II
. The messages notify you when to change the engine oil, or
when to bring your vehicle to a dealer for indicated maintenance services.
Displaying the Engine Oil Life
1. Turn the ignition switch to ON
II
.
2. Press the SEL /RESET button repeatedly until the engine oil life appears on the
multi-information display.
The system message indicator (
) comes on along with the Maintenance Minder
message.
Displaying the Engine Oil Life
Based on the engine operating conditions, the
remaining engine oil life is calculated and displayed
as a percentage.
Displayed Engine Oil
Life (%)Calculated Engine Oil
Life (%)
10 0 10 0 to 91
90 90 to 81
80 80 to 71
70 70 to 61
60 60 to 51
50 50 to 41
40 40 to 31
30 30 to 21
20 20 to 16
15 15 to 11
10 10 to 6
5 5 to 1
00
Maintenance Minder™
Maintenance
Service Items
Remaining
Engine Oil Life
SEL /RESET
Button