2011.5 Citroen C4 Owner's Manual

167
6
Safety

















Locations for ISOFIX child seats
mountings.
In the case of universal and semi-universal ISOFIX child seats, the ISOFIX size category, determined by a letter between Aand G
, is indicated on the child seat next to the ISOFIX logo.
Weight of the child
/ indicative age
Less than 10 kg (group 0)Up to approx. 6 months
Less than 10 kg(group 0)
Less than13 kg (group 0+)Up to approx. 1 year
From 9 to 18 kg (group 1)From approx. 1 to 3 years
Type of ISOFIX child seatinfant car seat"rear facing""rear facing" "for ward facing"
ISOFIX size categoryFGCDECDABB1
Universal and semi-universal ISOFIX child seats which can be installed on the outer rear seatsXXIL1IL2XIUF
IUF:seat suitable for the installation of an Isofix U
niversal seat, "F
orward facing" secured using the "Top Tether" upper strap.
For advice on securing of the "Top Tether" upper strap, refer to the "ISOFIX mountings" section.IL-:only the child seats indicated can be installed using the ISOFIX mountings.
X:seat not suitable for the installation of an ISOFIX seat of the size category indicated.
If in the way, the head restraint of the vehicle's ISOFIX seat must be removed and stowed safely.

168
Safety
The incorrect installation of a child seat in a vehicle compromises the child's protection inthe event of an accident.
Remember to fasten the seat belts or the child seat harnesses keeping the slackin relation to the child's body to a minimum
,
even for shor t journeys.
For optimum installation of the "for ward facing" child seat, ensure that the back of the child seat is in contact with the back of the vehicle's seat and that the head restraint does not cause any discomfort.
If the head restraint has to be removed,ensure that it is stored or attached securelyto prevent it from being thrown around the vehicle in the event of sharp braking.











Advice on child seats
Installing a booster seat
The chest par t of the seat belt must be
positioned on the child's shoulder without touching the neck.Ensure that the lap part of the seat belt passes correctly over the child's thighs.CITROËN recommends the use of a booster seat which has a back, fitted with a seat beltguide at shoulder level.
As a safety precaution, do not leave: - one or more children alone and unsuper vised in a vehicle, - a child or an animal in a vehicle which is exposed to the sun, with the windowsclosed, - the keys within reach of children insidethe vehicle.To prevent accidental opening of the doors, use the "Child lock".Take care not to open the rear windows bymore than one third.To protect young children from the rays of the sun, fit side blinds on the rear windows.

Children under the age of 10 must not travel in the "forward facing" position on the frontpassenger seat, unless the rear seats are already occupied by other children, cannot be used or are absent.
Deactivate the passenger's airbag when a
"rear facing" child seat is installed on thefront seat. Other wise, the child would risk being seriously injured or killed if the airbag were to inflate.

169
6
Safety







Child lock

Mechanical system to prevent opening of the rear doors using their interior controls.
The control is located on the edge of each rear door.


Child lock on
)Move the control A
towards position 1.
Child lock off
)
Move the control Atowards position 2
.

170
Practical information
This kit is installed in the boot under the floor. Complete s
ystem consisting of a compressor and a sealant car tridge which permits the
temporary repair of a tyre so that you can rdrive to the nearest garage.It is designed to repair most punctures which could affect the tyre, located on the tyre tread or shoulder.



















Temporary puncture repair kit
Access to the kit
1.12 V compressor with integral pressuregauge, to measure and adjust the tyre pressure.
F
or access to it:
)Open the boot.)Lift and remove the floor. )Ta k e out the kit.




Composition of the kit

The speed restriction sticker must beaffixed to the vehicle's steering wheel toremind you that a wheel is in temporaryuse.

Do not exceed a speed of 50 mph (80 km/h) when driving with a tyre repaired using this type of kit.
2.Sealant car tridge for the temporary repair
of a tyre. 3.Replacement valve core.4. Valve core removal/fitting tool.
5. Injection pipe.
6.Suction pipe, to remove the sealant product
if necessary.
7
. Speed limit sticker.

171
7
Practical information
1. Sealing

Repair procedure


Avoid removing any foreign bodies which have penetrated into the tyre.
)Stop the vehicle in as safe a location as
possible and on a level and stable surface. )Apply the parking brake. )Place the gear lever in position Rfor
vehicle with a manual gearbox, or inposition P for vehicles fitted with a CVT
gearbox. )Switch off the ignition. )Indicate on the speed restriction sticker provided, the wheel to be repaired, then fixit to the steering wheel as a reminder that a
wheel is in temporary use.

)
Remove the valve cap for the tyre to be
repaired. ) Remove the valve core using the toolprovided, and store in in a clean place.)
Connect the injection pipe to the valve of
the tyre to be repaired.
) Shake the sealant car tridge, remove thecap and screw on the injection pipe.

172
Practical information
Tap the sealant car tridge (top down)
several times with your hand, so as to inject
all of the product into the tyre. )Remove the injection pipe.)Refit the valve core and tighten it using the
tool provided.

Take care, this product is harmful (e.g. ethylene-glycol, colophony...) if swallowed andcauses irritation to the eyes.Keep it out of reach of children. The use-by date of the sealant is marked on the car tridge.
After use, do not discard the empty cartridge but take it to a CITROËN dealer (France) or an authorised waste disposal site. Don't forget to obtain a replacement cartridge; they are available from a CITROËN dealer or a qualified workshop.

173
7
Practical information

2. Infl ation
)Check that the compressor switch A
is in
the "OFF" position. )Uncoil the compressor pipe B
.
)
Connect this pipe to the valve of the
repaired wheel. )
Connect the compressor's electric plug to
the vehicle's 12 V socket (ignition switch in
position "ACC" or ACC mode).) Star t the compressor by turning the
switch A
to the "ON" position. )
Using the compressor, adjust the pressure in accordance with the vehicle's tyre
pressure label (located in the driver's door
aperture).
A loss of pressure indicates that the
puncture has not been fully plugged;contact a CITROËN dealer or a qualified
workshop for assistance.
) Remove the compressor and stow the kit. )
Drive off straight away at reduced speed (50 mph [80 km/h] max) for around 3 miles (5 km) or 10 minutes.


As soon as possible, go to a CITROËN dealer or a qualified workshop. Tell the technician that you have used the kit. After checking, the technicianwill advise you whether the tyre can berepaired or must be replaced.


If after around 10 minutes the pressure is not attained, this indicates thatthe tyre is not repairable; contacta CITROËN dealer or a qualifiedworkshop for assistance.

174
Practical information























Changing a wheel
The tools are stored in the boot under the floor.
To gain access to them: )Open the boot.)Lift and remove the boot floor. )Ta k e out the tools.
Access to the tools

List of tools

All of these tools are specific to your vehicle. Do not use them for anything else.1.Wheelbrace.
Used to remove the wheel trim and the
wheel fixing bolts.
2. Jack.
Used to raise the vehicle.
3. Handle.
Used to operate the jack. 4.Removable towing eye.
See "Recovering the vehicle".
5
.Security wheel bolt socket (available as an
accessory).
Used to adapt the wheelbrace to thespecial "security" wheel bolts. Procedure for replacin
g a faulty wheel with the spare wheel using the tools supplied with the vehicle.

Wheel with trim
When removing the wheel , remove the trim first using the handle 3
, pulling atthe cutout.When refitting the wheel
, refit the trim starting by placing its cutout opposite the valve and press on its outer edgewith the palm of your hand.