2010 Seat Alhambra wheel size

Heating, Ventilation and Air conditioning189
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Replacing the remote control battery
When the light Ÿpage 188, fig. 132 on the remote control does not
come on when the button is pressed, the remote control battery should soon
be replaced.
The battery is located beneath a cover on the back of the remote control. Turn
the slot to the left using a flat, blunt object (e.g. a coin). When changing the
battery, use another battery of the same model and observe the polarity when
fitting it Ÿ.
Range
The receiver is in the interior of the vehicle. The remote control, when fitted
with new batteries, has a range of several hundred metres. Obstacles
between the remote control and the vehicle, bad weather conditions and
discharged batteries can considerably reduce the range of the remote control.
An optimum range is obtained by keeping the remote control vertical, with
the aerial Ÿpage 188, fig. 132 pointing upwards. When doing so, do not
cover the aerial with your fingers or with the palm of your hand.
There must be a minimum distance of two metres between the remote control
and the vehicle.
Caution
xThe radiofrequency remote control contains electronic components.
Therefore, avoid getting the remote control wet and from being knocked and
protect it from direct sunlight.
xUse of inappropriate batteries may damage the remote control. For this
reason, always replace the dead battery with another of the same voltage,
size and specifications.
For the sake of the environment
Please dispose of old batteries so that they do not harm the environment.
For the sake of the environment
The remote control battery may contain perchlorate. Observe the legal
requirements for their disposal.
Programming the auxiliary heater
The heater or ventilation inside the vehicle can be programmed for a certain
period.
Before programming, check that the day is correctly set in the Auxiliary
heater - day of the week menu Ÿ.
Enabling the Auxiliary heater menu on the instrument panel
xFrom the main menu, select the Auxiliary heater submenu and press the
button on the windscreen wiper lever.
xALTERNATIVELY: press the or arrow buttons on the multi-function
steering wheel until the Auxiliary heater menu is displayed.
a)Within its range, the remote control might not receive the signal sent by the vehicle
receiver. In this case, the remote control will send an error message despite the aux-
iliary heater being on or off. Come closer to the vehicle and press the corresponding
button on the remote control once again.
AB
AAOK
ƒ„

Wheels and tyres323
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Wheels and tyres
Wheels
Introduction
SEAT recommend that all work on tyres and wheels is carried out by a quali-
fied workshop. They have the necessary special tools and replacement parts,
trained personnel and facilities for disposing of the old tyres. SEAT recom-
mends visiting a qualified workshop.
Additional information and warnings:
xTransporting Ÿpage 13
xTo wi ng m o d e Ÿpage 260
xBraking, stopping and parking Ÿpage 210
xPark assist system Ÿpage 229
xTyre control systems Ÿpage 245
xCaring for and cleaning the vehicle exterior Ÿpage 269
xWheel trims Ÿpage 336
xChange wheel Ÿpage 339
xNotes for the user Ÿpage 283
WARNING
The vehicle cannot be totally controlled or braked if the tyres (new or used)
are worn or damaged.
xIncorrect use of wheels and tyres could make driving more dangerous
and result in serious accidents and damage.
xAll four wheels must be fitted with radial tyres of the same type, size
(rolling circumference) and the same tread pattern.
xNew tyres do not give maximum grip and will not have reached their
maximum braking capacity to start with, and therefore need running in. To
prevent accidents and major damage, extreme caution should be taken for
the first 600 km (370 miles).
xCheck tyre pressures regularly and ensure they are maintained at the
pressures indicated. If the tyre pressure is too low, the tyres could over-
heat, resulting in tread detachment or even burst tyres.
xNever drive on damaged (punctured, cut, cracked or dented) or worn
tyres. Driving on damaged or worn tyres could result in burst tyres, serious
accidents or damage. Worn or damaged tyres must be replaced immedi-
ately.
xNever exceed the maximum permitted speed or loads specified for the
type of tyre fitted on your vehicle.
xThe efficiency of driver and brake assist systems also depends on the
grip of the tyres.
xIf you notice unusual vibration or if the vehicle pulls to one side when
driving, stop the car immediately and check the tyres and wheels for
damage.
xTo minimise the risk of losing control of the vehicle or causing a serious
accident, never undo the bolted joints of beadlock wheels.
xNever mount used tyres or wheels if you are not sure of their previous
history. They may be damaged, although the damage is not immediately
visible.
xOld tyres, even if they have never been used, may lose air or burst unex-
pectedly while driving, resulting in serious accident or damage. If tyres are
over six years old, they should only be used in an emergency and with
extreme caution.
WARNING (continued)

Wheels and tyres327
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
The use of worn or damaged wheel rims could make driving more
dangerous and result in serious accidents and damage.
xOnly wheel rims which have been approved for use with your vehicle
should be used.
xInspect wheel rims regularly for damage and replace as required.
WARNING
If the bolted joints of wheel rims with bolted ring trims are not correctly
tightened or loosened, this could result in serious accident.
xNever loosen the bolted joints of wheel rims with bolted ring trims.
xAny work relating to wheel rims with bolted rims should be carried out
at qualified workshop. SEAT recommends visiting a qualified workshop.
Replacement of new tyres and wheel rims
New tyres
xWhen tyres are new, drive with extreme caution for the first 500 km (310
miles), as all tyres need to be run-in. Tyres which have not been run-in do not
have such good grip Ÿ or braking capacity Ÿ.
xAll four wheels must be fitted with radial tyres of the same type, size
(rolling circumference) and the same tread pattern.
xThe tread depth of new tyres may vary, according to the type and make of
tyre and the tread pattern.
Replacing tyres
xWhere possible, always replace both wheels on an axle (both wheels on
the front axle or both wheels on the rear axle) Ÿ.
xOld tyres should only be replaced by SEAT approved tyres for the vehicle
in question, and in accordance with the maximum permitted size, diameter,
load and speed capacity.
xNever use tyres which are larger than SEAT approved tyres. If the tyres are
too big, they may knock or rub against the chassis or other components,
resulting in damage.
WARNING
New tyres do not give maximum grip and will not have reached their
maximum braking capacity to start with, and therefore need running in.
xTo prevent accidents and major damage, extreme caution should be
taken for the first 600 km (370 miles).
WARNING
There should be adequate space between the tyres and the vehicle in
accordance with the vehicle design. If this is not the case, the tyres may rub
against parts of the running gear, chassis or brake lines, leading to faults
in the brake system or to tread detachment, and the risk of burst tyres.
xThe true tyre dimension should not be greater than the dimensions of
tyres manufactured and approved by SEAT and should not rub against parts
of the vehicle.
Note
Although tyres may be shown as being the same size, the true dimensions of
different types of tyre may vary with respect to the nominal size, or tread
patterns may be different.
Note
If you use tyres that are approved by SEAT, you can be sure that the true tyre
dimensions will be correct for your vehicle. For other tyre models, the tyre

Wheels and tyres331
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xNever carry on driving on worn tyres or wheels. Request qualified
assistance immediately.
xIf there is no visible exterior damage, drive slowly and carefully to the
nearest qualified workshop and have the vehicle checked.
Winter tyres
In winter conditions winter tyres will considerably improve the vehicles
handling. The design of summer tyres (width, rubber compound, tread
pattern) gives less grip on ice and snow. SEAT strongly recommends using
winter tyres or all year round tyres on all four wheels of the vehicle, especially
if you expect to drive in wintery weather. Winter tyres also improve the vehicle
braking performance, reducing the braking distance in winter weather. SEAT
recommend that winter tyres be fitted to the vehicle at temperatures below
+7 °C (+45 °F).
The performance of winter tyres is much reduced if the tyre tread is worn
below 4 mm (1/16 inch). The age of the tyre is another factor affecting
performance, regardless of the depth of the tyre tread.
Please observe the following when using winter tyres:
xObserve legal requirements in each country.
xWinter tyres must be fitted on all four wheels.
xOnly use winter tyres in wintery weather conditions.
xOnly use winter tyres of the size authorised for the vehicle.
xOnly use radial winter tyres of the same type, size (rolling circumference)
and tread pattern.
xAdjust speeds to within the limits indicated (code letter on tyre) Ÿ.Speed limit
A code letter indicating the speed limit is stamped on all winter tyres
Ÿpage 334.
In some vehicles, it is possible to set a speed warning in the MFA
(multifunction indicator) menu on the instrument panel Ÿpage 70.
If you use V-rated tyres the speed limits and tyre pressure will be determined
by engine size. Please ask your SEAT qualified workshop for further informa-
tion on the maximum permitted speed and the required pressures for the
tyres.
All-wheel drive
Thanks to its all-wheel drive, your car will have plenty of traction in winter
conditions, even with the standard tyres. Nevertheless, SEAT still recommend
that winter tyres or all-season tyres should be fitted on all four wheels when
winter road conditions are expected, mainly because this will give a better
braking response.
Please observe all instructions and warnings when using snow chains
Ÿpage 332.
WARNING
Although winter tyres help to make driving safer in the winter, you should
not take unnecessary risks.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
xNever exceed the maximum permitted speed or loads specified for the
type of winter tyre fitted on your vehicle.
For the sake of the environment
When winter is over, change back to summer tyres. In temperatures above
+7 °C (+45 °F), performance will be improved if summer tyres are used. Fuel
consumption, wear and noises while driving will all be reduced.
WARNING (continued)

Wheels and tyres 332
Note
If the vehicle is fitted with a tyre control system, this should be “repro-
grammed” whenever a tyre is changed Ÿpage 248.
Note
Please ask at SEAT qualified workshops for information about the permitted
sizes for winter tyres.
Snow chains
When using snow chains, applicable local legislation and maximum
permitted speed limits must be observed.
In winter weather, snow chains not only help to improve grip but also improve
the braking capacity.
Snow chains must only be mounted on the front wheels, even on all-wheel
drive vehicles, and only with the tyre and rim combinations listed below:
SEAT recommends you ask a SEAT qualified workshop for further information
on wheel, tyre and chain sizes.
Wherever possible use fine-link chains measuring less than 15 mm (37/64
inch) including the lock.
Remove wheel hub covers and trim rings before fitting snow chains Ÿ.
The wheel bolts should be covered with caps for safety reasons. These are
available from qualified workshops.
WARNING
The use of unsuitable or incorrectly fitted chains could lead to serious acci-
dents and damage.
xAlways the appropriate snow chains.
xObserve the fitting instructions provided by the snow chain manufac-
turer.
xNever exceed the maximum permitted speeds when driving with snow
chains.
Caution
xYou must remove the snow chains to drive on roads which are free of
snow. Otherwise they will impair handling, damage the tyres and wear out
very quickly.
xWheel rims may be damaged or scratched if the chains come into direct
contact with them. SEAT recommends the use of covered snow chains.
Note
Snow chains are available in different sizes according to the vehicle type.Tyre sizeWheel rim
205/60 R166 1/2 J x 16 ET 33
215/60 R166 1/2 J x 16 ET 33

Wheels and tyres333
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Tyre code
Fig. 185 Universal code on tyres.
Radial
Rim diameter code
Load index & speed rating
DOT tyre identification number
Severe snow conditions
Tyre ply composition and materials used
Max. load rating
Treadwear, traction and temperature grades
Max. permissible inflation pressure
Passenger car tyre
Nominal width of tyre in millimetres
Ratio of height to width (aspect ratio)A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
Tyre code (example)Meaning
Make, logotypeManufacturer
Product nameName of tyre assigned by manufacturer.
P215 / 55 R 16Size:
PPassenger vehicle code.
215Nominal width between walls, in mm.
55Height/width ratio in %
RTyre type (R indicates "radial").
16Rim diameter in inches
91 VLoad index Ÿpage 334 and speed rating
Ÿpage 334.
XLReinforced tyres.
M+S or M/SWinter tyres (mud and snow tyres) Ÿpage 331.
SSR or DSST, Eufonia,
RFT, ROF, RSC, ZPSpecific manufacturer codes for run-flat tyres.
RADIAL TUBELESSRadial tyre without inner tube.
E4 ...E-mark certifying tyre complies with international
legislation followed by a number denoting the
country granting the authorisation. The authori-
sation number ( several digits) is shown below.

Wheels and tyres 334
Tyres with directional tread pattern
Tyres with directional tread pattern have been designed to operate best when
rotating in only one direction. An arrow on the tyre sidewall indicates the
direction of rotation on tyres with directional tread. Always observe the direc-
tion of rotation indicated when mounting the wheel. This guarantees
optimum grip and helps to avoid aquaplaning, excessive noise and wear.
Tyre load ra tin g
The load rating code indicates the maximum load in kilogrammes each wheel
can carry (load capacity).
91 615 kg (1,356 pounds)
93 650 kg (1,433 pounds)
95 690 kg (1,521 pounds)
97 730 kg (1,609 pounds)
99 775 kg (1,709 pounds)
Speed rating
The speed rating indicates the maximum speed permitted for the tyres.
P max. 150 km/h (93 mph)
Q max. 160 km/h (99 mph)
R max. 170 km/h (106 mph)
S max. 180 km/h (112 mph)
DOT BT RA TY5 1709Tyre identification number (TINa), may be only on
interior wall of wheel) and date of manufacture:
DOTThe tyre complies with the legal require-
ments of the US Department of Transport,
responsible for tyre safety regulations.
BTPlace of manufacture code.
RAInformation about manufacturer and tyre
size.
TY5Manufacturer's tyre specifications.
1709Date of manufacture: Week 17 of 2009.
TWIThis identifies the position of the Tread Wear
Indicator Ÿpage 329.
Made in GermanyCountry of manufacture.
MAX LOAD 615 KG (1356
LBS)US load rating, indicating maximum permitted
load per tyre.
MAX INFLATION 350 KPA
(51 PSI)US limit, indicating maximum permitted tyre
pressure.
SIDEWALL 1 PLY RAYONInformation about tyre wall components:
1 layer of rayon (artificial silk).
TREAD 4 PLIES
1 RAYON + 2 STEEL + 1
NYLONInformation about tread components:
In the example, there are 4 layers below the
tread: 1 layer of rayon (artificial silk), 2 layers of
steel reinforcement and 1 layer of nylon.
Information for the end consumer concerning the comparative values of
the established base tyres (standardised test procedures):
TREADWEAR 280Relative service life of the tyre, with respect to
specific US standard test.
Tyre code (example)Meaning
TRACTION AABraking capacity of tyre on wet surface (AA, A, B
or C).
TEMPERATURE ATyre temperature resistance at higher test speeds
(A, B or C).
If the tyre has other markings, these are specific tyre manufacturer codes
or specific national codes, e.g. for Brazil or China.
a)The letters TIN refer to the tyre serial number.
Tyre code (example)Meaning

General notes on the technical data 382
Towing a trailer
Trailer weights
Trailer weight
The trailer weights and drawbar loads approved are selected in intensive
trials according to precisely defined criteria. The approved trailer weights are
valid for vehicles in the EU for maximum speeds of 80 km/h (in certain
circumstances up to 100 km/h). The figures may be different in other coun-
tries. All data in the official vehicle documents take precedence over these
data Ÿ.
Drawbar load
The maximum permitted weight exerted by the trailer drawbar on the ball joint
of the towing bracket must not exceed 85 kg.
In the interest of road safety, we recommend that you always tow
approaching the maximum drawbar load. The response of the trailer on the
road will be poor if the drawbar load is too small.
If the maximum permitted drawbar load is not reached (e.g. in the case of
small single-axle trailers, light and without load, or tandem axle trailers with
a wheelbase of less than 1 m) it is compulsory for the drawbar load to be at
least 4% of the trailer's weight.
WARNING
xFor safety reasons, do not exceed the 80 km/h limit. This is also valid in
countries where higher speeds are permitted.
xNever exceed the maximum trailer weights or the drawbar load. If the
permissible axle load or the permissible total weight is exceeded, the
driving characteristics of the vehicle may change, leading to accidents,
injuries and damage to the vehicle.
Wheels
Tyre pressure, snow chains, wheel bolts
Tyre pressures
The sticker with the tyre pressure values can be found on the inside of the
tank flap. The tyre pressure values given there are for cold tyres. The slightly
raised pressures of warm tyres must not be reduced. Ÿ
Snow chains
Snow chains may be fitted only to the front wheels.
Consult the chapter “wheels” of this manual.
Wheel bolts
After the wheels have been changed, the tightening torque of the wheel bolts
should be checked as soon as possible with a torque wrench Ÿ. The tight-
ening torque for steel and alloy wheels is 120 Nm.
WARNING
xCheck the tyre pressure at least once per month. Checking tyre pressure
value is very important. If the tyre pressure is too high or too low, there is
an increased danger of accidents, particularly at high speeds.
xIf the torque of the wheel bolts is too low, they could loosen while the
vehicle is in motion. Risk of accident! If the tightening torque is too high,
the wheel bolts and threads can be damaged.
Note
We recommend that you ask your Authorised Service Centre for information
about appropriate wheel, tyre and snow chain size.