2010 Seat Alhambra diagram

Seat belts 24
Fastening or unfastening the seat belt with two buckles
Properly worn seat belts hold the vehicle occupants in the position that most
protects them in the event of an accident or sudden braking Ÿ.
The seat belts for the centre seat in the second row of seats and for the seats
in the third row of seats are fastened using two buckles.
Fastening the seat belt
Fasten your seat belt before each trip.
xAdjust the rear seat and head restraint correctly Ÿpage 10.
xEngage the backrest of the rear seat in an upright position Ÿ.
xUse latch plate of the belt Ÿfig. 12 to pull the seat belt down. Do not
twist the seat belt when doing so Ÿ.
xEngage the latch plate in the buckle of the corresponding seat .
xUse the latch plate Ÿfig. 12 to pull the seat belt across your lap.
xEngage the latch plate in the buckle of the corresponding seat .
xPull the belt to ensure that both latch plates are securely engaged in the
buckles.
Unfastening the seat belt
The seat belt must not be unfastened until the vehicle has come to a standstill
Ÿ.
xPress the red button on the buckle Ÿfig. 12 . The latch plate is
released from the buckle.
xPress the red button on the buckle Ÿfig. 12 . The latch plate is
released from the buckle.
xGuide the belt back by hand so that it rolls up easily and the trim will not
be damaged.
WARNING
An incorrectly worn seat belt web can cause severe or fatal injuries in the
event of an accident.
xThe seat belt cannot offer its full protection unless the backrests are in
an upright position and the seat belt is worn correctly, according to your
size.
xUnbuckling your seat belt while the vehicle is in motion can cause
severe or fatal injuries in the event of an accident or sudden braking.
Note
Seat belts with two buckles include a diagram to show how to fasten the seat
belt.
Fig. 12 Fasten the seat
belt on the centre seat in
the second row of seats.
A1
A1AA
A2
A2AB
AA
AB

Lights and visibility 116
Turning on and off lights
The legal requirements regarding the use of vehicle lights in each country
must be observed.
In vehicles with tow bar fitted as standard: If the trailer is connected electri-
cally and is fitted with a rear fog light, this is automatically switched off on the
vehicle.
Turn the light switch to the required position Ÿfig. 67:
Fog lights
The warning lamps
or
on the light switch also indicate that the fog
lights are switched on.
Fig. 67 Next to the steering wheel: diagram of some of
the types of light switch.
when the ignition is turned offwhen the ignition is on
/Fog lights, dipped beam and
side lights off.Lights off or daytime driving light
on.
!54/The guidance lights may be
switched on.Automatic dipped beam control
or daytime driving light on.
Side light on.Side light on.

Dipped beam off; if necessary,
the side light comes on for a
time.Dipped beam switched on.

Seats and storage compartments 160
Securing the base supports and roof carrier system
The mounts are the basis of a complete roof carrier system. Special fixtures
must then be added in order to safely transport luggage, bicycles, skis, surf
boards or boats on the roof. All these system components are available from
an Authorised Service Centre.
It will only be possible to install a basic support or roof carrier system if the
vehicle has a roof rail.
Securing the base supports and roof carrier system
Always secure the base supports and roof carrier system correctly.
The roof carrier system must always be installed exactly according to the
instructions provided.
The position holes are located on the inner side of the rail Ÿfig. 107.
WARNING
If the base supports and the roof carrier system are incorrectly fitted or
used in an unsuitable manner, the entire system could break free causing
accident and injury.
xAlways take the manufacturer assembly instructions into account.
xOnly use base supports and roof carrier systems that are not damaged
and are correctly fitted.
xThe base support should only be fitted to the points indicated in the
diagram Ÿfig. 107.
xSecure the base supports and roof carrier system correctly.
xCheck the screw fittings and attachments before driving and after a
short distance. During each long journey, check the attachments during
every break.
xAlways fit the roof carrier system correctly for wheels, skis and surf-
boards.
xNever change or repair the basic supports or roof carrier system.
Note
Read and take into account the instructions included with the roof carrier
system fitted and keep them in the vehicle.
Loading the roof carrier system
Loads can only be correctly secured when the roof carrier system is correctly
fitted Ÿ.
Maximum authorised roof load
The maximum authorised roof load is 100 kg (about 220 lbs). The roof load
includes the roof carrier system and the load being transported Ÿ.
Fig. 107 Attachment
points for the basic
support and the roof
carrier system.

Wheels and tyres325
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
About your tyres and wheels
The tyres of a vehicle are the components which are subjected to most stress
and are the most underestimated. Tyres are very important, as the support
offered by their narrow surface is the only point of contact between the
vehicle and the road.
The service life of tyres is dependent on tyre pressure, driving style, the care
they receive and the correct fitting.
The tyres and wheel rims are an essential part of the vehicle's design. The
tyres and rims approved by SEAT are specially matched to the characteristics
of the vehicle and our critical to good road holding and safe handling.
Avoiding damage to tyres and wheels
xIf you have to drive over a kerb or similar obstacle, drive very slowly and
as near as possible at a right angle to the kerb.
xInspect the tyres regularly for damage (punctures, cuts, cracks, dents).
xRemove any foreign bodies found on the outside of the tread provided
they have not passed through the wall of the tyre Ÿpage 330.
xThe instructions for tyre control systems should always be observed.
xReplace damaged or worn tyres as soon as possible Ÿpage 330.
xRegularly check tyres for non-visible damage Ÿpage 330.
xNever exceed the maximum permitted speed or loads specified for the
type of tyre fitted on your vehicle Ÿpage 333.
xDo not allow tyres to come into contact with aggressive substances,
grease, oil, fuel or brake fluid Ÿ.
xLost valve caps should be replaced immediately.
Tyres with directional tread pattern
Tyres with directional tread pattern have been designed to operate best when
rotating in only one direction. An arrow on the tyre sidewall indicates the
direction of rotation on tyres with directional tread Ÿpage 333. Always
observe the direction of rotation indicated when mounting the wheel. This
guarantees optimum grip and helps to avoid aquaplaning, excessive noise
and wear.
If the tyre is mounted in the opposite direction of rotation, drive with extreme
caution, as the tyre is no longer being used correctly. This is of particular
importance when the road surface is wet. Change the tyre as soon as possible
or remount it with the correct direction of rotation.
Interchanging tyres
To ensure that the wear is equal on all tyres the wheels should be changed
round from time to time according to the system Ÿfig. 182. All the tyres will
then last for about the same time.
SEAT recommends you take the vehicle to a qualified workshop to have the
tyres changed.
Tyres that are over 6 years old
Tyres are subject to an ageing process as a result of physical and chemical
processes. This may affect their performance. Tyres which are stored for long
periods of time without being used, harden and become more fragile than
tyres which are in constant use.
Fig. 182 Diagram for
changing wheels

If and when 372
Positive pole on the starting assistance points
On some vehicles, there is a starting assistance terminal in the engine
compartment, under a labelled cover.
How to jump start: description
The discharged battery must be properly connected to the vehicle electrical
system.
Fig. 225 In the engine
compartment: positive
pole for starting assist-
ance .
A+
Fig. 226 Jump lead
connection diagram when
the assistance vehicle
does not have a Start-
Stop system: flat battery
and battery supplying
current .
AAAB
Fig. 227 Jump lead
connection diagram when
the assistance vehicle has
a Start-Stop system: flat
battery and battery
supplying current .
AAAB

Technical Data383
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Technical Data
Checking fluid levels
From time to time, the levels of the different fluids in the
vehicle must be checked. Never fill with incorrect fluids,
otherwise serious damage to the engine may be caused.
Fig. 231 Diagram for the location of the various elements
Liquid coolant deposit
Engine oil dipstick
Oil filler neck
Brake fluid reservoir
Vehicle battery (underneath a cover)
Windscreen washer fluid reservoir
The checking and refilling of service fluids are carried out on the components
mentioned above. These operations are described in Ÿpage 304.
Overview
Further explanations, instructions and restrictions on the technical data are
contained as of Ÿpage 379A1
A2
A3
A4
A5
A6