2010 Seat Alhambra reset

Unlocking and locking101
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xHold down the button Ÿpage 100, fig. 59 with the tailgate open for at
least three seconds.
xThe opening angle is reset to the original factory setting.
WARNING
Unsuitable or careless closing and locking of the tailgate could cause
serious injuries.
xNever allow children to play inside or around the vehicle without super-
vision, especially if the tailgate is open. Children could enter the luggage
compartment, close the tailgate and become trapped. A locked vehicle can
be subjected to extremely high and low temperatures, depending on the
time of year, thus causing serious injuries/illness and even death.
WARNING
It is possible that the tailgate does not open completely or, if it is open,
closes alone if a large amount of snow has built up on it or if a luggage rack
is fitted. In this case, the tailgate must be supported.
Caution
xWhen using a trailer, ensure that there is sufficient space to open and
close the tailgate.
xBefore opening the tailgate, any kind of equipment carrier should be
removed, for example a bicycle carrier.
Caution
In case of repeated short-term use, the system is turned off to avoid over-
heating.
xWhen it has cooled, it may be used once again. During this time, the tail-
gate may be manually opened or closed applying a little more effort.
xIf the vehicle battery is disconnected or the fuse blows when the tailgate
is open, the tailgate system must be re-initialised. To do this, close the tail-
gate.
Note
Before closing the tailgate, make sure that the key has not been left inside the
boot.

Unlocking and locking 104
To stop the one touch function: Push or pull on the button of the corre-
sponding window.
Restoring one-touch opening and closing
The one-touch opening and closing function is not active after the vehicle
battery has been disconnected or is flat and will have to be reset.
xClose all windows and doors.
xPull the button of the corresponding window and hold it for one second in
this position.
xRelease the button and pull upwards and hold again. The one-touch func-
tion is now ready for operation.
The automatic one-touch electric windows can be reinitialised individually or
several at a time.
Convenience opening and closing function
The electric windows can be opened or closed from outside using the vehicle
key:
xHold in the unlocking for locking button for the vehicle. All windows which
function electrically will be either opened or closed.
xTo interrupt the function, release the locking or unlocking button.
During convenience closing, first the windows and then the sliding sunroof
will be closed.
In the Configuration - convenience menu, there are different settings for oper-
ating the windows Ÿpage 70.
WARNING
Careless use of the electric windows can cause serious injury.
xOnly operate the electric windows when nobody is in the way.
xNever leave children or disabled people alone in the vehicle if the doors
are to be locked. The windows cannot be opened in case of an emergency.
xAlways take all the keys with you whenever you leave the vehicle. After
turning off the ignition, the windows can be opened and closed for a short
time using the buttons on the door as long as the driver's door or
passenger side door is not open.
xWhen transporting children in the rear seats, always deactivate the rear
electric windows with the child safety lock so that they cannot be opened
and closed.
Note
The one-touch function and roll-back function will not work if there is a
malfunction in the electric windows. Visit a specialist workshop.
Electric Windows anti-trap function
The anti-trap function of the electric windows can reduce the risk of injury
when opening and closing the electric windows Ÿ. If a window is not able
to close because it is stiff or because of an obstruction, it will automatically
open again.
xCheck why the window does not close.
xAttempt to close the window again.
xIf you try within the following 10 seconds and the window closes with
difficulty or there is an obstruction once again, the one-touch closing will stop
working for 10 seconds.
xIf the window is still obstructed, it will stop at the corresponding position.
When the button is operated within 10 seconds, the window will close
without the anti-trap function Ÿ.
WARNING (continued)

Lights and visibility 120
function is switched on. If the equipment includes the light sensor, the
lighting around the exterior mirrors only comes when it is dark.
Note
The time taken for the headlights to go off can be changed in the menu Lights
& Visibility and the function can be switched on or off Ÿpage 70.
Note
When the “Coming home” function is on, if the vehicle door is opened there
is no audible warning signal to advise that the light is still on.
Headlight range control, instrument and switch lighting
Instrument and switch lighting
When the headlights are switched on, the brightness of the instruments and
switch lighting can be regulated to suit your requirements by turning the
switch Ÿfig. 68 .
Headlight range control
The headlight range control Ÿfig. 68 is modified according to the value
of the headlight beam and the vehicle load status. This offers the driver
optimum visibility and the headlights do not dazzle oncoming drivers Ÿ.
The headlights can only be adjusted when the dipped beam is switched on.
To reset, turn switch Ÿfig. 68 :
Dynamic headlight range control
The control is not mounted in vehicles with dynamic headlight range
control. The headlight range is automatically adjusted according to the
vehicle load status when the headlights are switched on.
WARNING
Heavy objects in the vehicle may mean that the headlights dazzle and
distract other drivers. This could result in serious accident.
Fig. 68 Next to the
steering wheel: instru-
ment and switch lighting
control and headlight
range control .
A1A2
ValueVehicle load statusa)
a)If the vehicle load does not correspond to those shown in the table, it is possible to
select intermediary positions.
–Two front occupants, luggage compartment empty
1All seats occupied, luggage compartment empty
2All seats occupied, luggage compartment full. With trailer
and minimum support load
3Driver only, luggage compartment full. With trailer and
maximum support load
A1
A1
A2
A2
A2
A2

Driving 224
Important conditions for the engine to automatically switch off
xThe driver seat belt must be buckled.
xThe driver door must be closed.
xThe bonnet must be closed.
xThe factory-fitted towing bracket must not be electrically connected to a
trailer.
xA minimum engine temperature has been reached.
xThe vehicle has moved since the last stop.
xIn vehicles with Climatronic: The temperature inside the vehicle is within
the preset temperature range.
xThe temperature set is neither very high nor very low.
xThe air conditioning defrost function is not switched on.
xIn vehicles with Climatronic: the blower has not been manually set to a
high speed.
xThe power level of the vehicle's battery is sufficient.
xThe vehicle's battery temperature is neither too high nor too low.
xThe vehicle is not on a steep gradient or slope.
xThe front wheels are not overly turned.
xThe heated windscreen is not switched on.
xReverse gear is not engaged.
xThe park assist system is not switched on.
Conditions for automatically restarting the engine
The engine may automatically restart under the following conditions:
xIf the vehicle interior is too hot or too cold.
xIf the vehicle moves.
xIf the vehicle's battery voltage drops.
Conditions requiring the key to restart the engine
The engine must be started using the key under the following conditions:
xIf the driver unbuckles his/her seat belt.
xIf the driver's door is opened.
xIf the bonnet is opened.
xIn vehicles with a manual gearbox: If a gear has been selected.
Switching Start-Stop mode on and off manually
xPress the button on the centre console Ÿpage 223, fig. 147.
xThe button will light up when the Start-Stop function is switched off.
The engine will start immediately if the vehicle is in Stop mode when it is
switched off manually.
WARNING
The brake servo and the power steering do not work when the engine is
switched off.
xNever allow the vehicle to move when the engine is switched off.
Caution
Using the Start-Stop function for a long period at very high outdoor tempera-
tures could damage the vehicle's battery.
Note
In some cases, you may have to restart the vehicle using the key. Observe the
corresponding message on the instrument panel display.
›

Accessories, parts replacement and modifications289
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a The storing of the data allows specialised workshops to detect and repair
faults. Stored data may include:
xData relating to the engine or the gearbox
xSpeed
xDirection of travel
xBraking force
xDetection of seat belt
The vehicle control units never record conversations held by passengers in
the vehicle.
In vehicles equipped with an emergency call function via the mobile phone or
other appliances connected in the vehicle, it is possible to send the vehicle
position. If the control unit records an accident with airbag activation, the
system may automatically send a signal. This will depend on the network
operator. Normally, transmission is only possible in areas with good
coverage.
Event Data Recorder
The vehicle is not fitted with an event data recorder.
An event data recorder temporarily stores the vehicle information. Therefore,
in the event of accident, it is possible to obtain detailed information about
how the accident occurred. For example, in vehicles with airbag systems,
data relating to speed of impact, seat belt status, seat positions and airbag
activation times may be stored. The volume of data depends on the manufac-
turer.
Event data recorders can only be mounted with authorisation from the vehicle
owner and, in some countries, they are governed by local legislation.
Reprogramming control units
On the whole, all the data required for the component management is stored
in the control units. The programming of certain convenience functions, such
as the convenience indicators, individual door opening and instructions on
the display can be modified using special equipment at the workshop. If this is the case, the information and descriptions given in the instructions manual
will not match the original functions. Therefore, SEAT recommends that any
modifications are recorded in the section “Other workshop notes” in the
Maintenance Programme.
The Technical Service must have a record of any modification to the program-
ming.
Reading the vehicle fault memory
There is a diagnostics connector in the vehicle interior for reading the vehicle
fault memory. The fault memory documents errors and deviations from the
theoretical values of the electronic control units.
The diagnostics connector is in the driver's side footwell area, next to the
lever for opening the bonnet, below a cover.
The fault memory should only be read and reset by a qualified workshop.
Using a mobile telephone in a vehicle without connection to
an exterior aerial
Mobile telephones transmit and receive radio waves, both when in use and
when on stand-by. Scientific studies state that radio waves exceeding certain
values may be harmful to the human body. International committees and
authorities have established limits and directives in order to ensure electro-
magnetic radiation from mobile phones remains within certain limits that do
not endanger human health. However, there is no available conclusive scien-
tific evidence that cordless phones are completely safe.
Therefore, some experts recommend that use of mobile phone be kept to a
minimum until the results of current research are published.
When a mobile phone not connected to an exterior aerial is used inside the
vehicle, the electromagnetic radiation may be greater than if the mobile
phone were connected to a built-in aerial or to another exterior aerial.