2010 Seat Alhambra ECO mode

Cockpit 74
Possible displays
Changing between display modes
xIn vehicles without multifunction steering wheel: press the lever.
xVehicles with a multifunction steering wheel: press or .
Storing a speed for the speed warning
xSelect the display Speed warning at --- km/h.
xPress to store the current speed and switch off the warning.
xIn addition, set the required speed by pressing the rocker switch on the
windscreen wiper lever or buttons or on the multifunction steering
wheel for 5 seconds. Next, press again or wait a few seconds. The speed
is stored and the warning activated.
xTo switch off, press . The stored speed is deleted.
Manually erasing memory 1 or 2
xSelect the memory to be erased.
xPress and hold for approximately two seconds.
Personalising the displays
It is possible to select which of the displays in the multifunction display you
wish to see on the instrument panel in the settings menu. The units of meas-
urement can also be modified Ÿpage 75.
MenuFunction
Journey durationThis indicates the hours (h) and minutes (min) since
the ignition was switched on.
Current fuel
consumptionThe current fuel consumption while driving is dis-
played in l/100 km (or miles per gallon, mpg); when
the engine is running but the vehicle is not moving,
in l/h (or gallons per hour).
Average fuel
consumptionWhen the ignition is switched on, the average con-
sumption (in l/100 km or in mpg) is displayed after
the vehicle has moved approximately 100 metres
(328 feet). Otherwise horizontal lines are displayed.
The value shown is updated approximately every 5
seconds.
Distance to empty
(the distance you
can travel with the
remaining fuel)Approximate distance in km (or miles) that can still
be travelled with the fuel remaining in the tank,
assuming the same style of driving is maintained.
This is calculated using the current fuel consumption.
Distance coveredDistance travelled, after ignition is switched on, in km
(or miles).
Average speedAfter the ignition is switched on, the average speed
will be shown after a distance of approximately 100
metres (328 feet) has been travelled. Otherwise hori-
zontal lines are displayed. The value shown is
updated approximately every 5 seconds.
Digital display of
speedCurrent speed displayed digitally.
Oil temperature
digital displayUpdated engine oil temperature digital display
Speed warning
to --- km/hIf the stored speed is exceeded (between 30 - 250
km/h, or 18 - 155 mph), an audible warning is given
together with a visual warning.
MenuFunction
*+
OK
*+OK
OK
OK

Cockpit75
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Configuration Menu
Configuration
MenuFunction
Multifunction
display dataConfiguration of the multifunction display data which you
wish to see on the instrument panel display Ÿpage 73.
CompassChanging the magnetic region and calibration of the com-
pass. To calibrate the compass, please follow the instruc-
tions given on the instrument panel display.
ConvenienceChanging vehicle convenience functions Ÿpage 76.
Lights &
visibilityConfiguration of vehicle lighting Ÿpage 77.
TimeChanging the hours and minutes of the clock and the nav-
igation system. The time can be set here and the choice
can be made between the 24 hour and 12 hour display.
The S in the upper part of the display indicates that the
clock is set to summer time.
Winter tyresChanging the visual and audible speed warnings. This
function should only be used when the vehicle is fitted
with winter tyres, which are not designed for travel at
high speeds.
Settings:
LanguageChanging the language of the display texts and the navi-
gation system.
UnitsChanging the units of measurement for the temperature,
consumption and distance.
Second speedSwitching second speed display on and off
AutoholdSelecting whether the Auto-Hold function should remain
on permanently.
Travel modeChanging the headlamps for countries in which vehicles
are driven on the other side of the road. When the “mark”
is activated, the headlamps of a left-hand drive vehicle
are adjusted for driving on the left. The travel mode can
only be used for short periods of time.
ServiceCheck the service notifications or reset the service inter-
vals to zero
Manufacturer's
settings Some functions of the Configuration menu will be reset
to the factory value.
BackThe main menu is displayed again.
Configuration
MenuFunction

Unlocking and locking81
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a the indicator blinks several times, for example: for the convenience opening
function.
When the indicator light does not light upon pushing a button, the batteries
of the vehicle key must be changed Ÿpage 81.
Changing the battery
SEAT recommend having the batteries changed in a qualified workshop.
The battery is located to the rear of the vehicle key, under a cover Ÿfig. 44.
When changing the battery, use another battery of the same model and
observe the polarity when fitting it Ÿ.
To change the battery
xUnfold the key shaft Ÿpage 79.
xRemove the cover from the back of the vehicle key Ÿfig. 44 in the direc-
tion of the arrow Ÿ.
xExtract the battery from the compartment using a suitable thin object
Ÿfig. 45.
xPlace the new battery in the compartment, pressing in the direction of the
arrow as shown Ÿfig. 45 Ÿ.
xFit the battery compartment cover, pressing in the direction of the arrow
as shown Ÿfig. 44 until it clicks into place.
Fig. 44 Vehicle key:
battery compartment
cover.
Fig. 45 Vehicle key:
removing the battery.

Lights and visibility119
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
The headlights, rear lights and turn signals may mist up temporarily on the
inside in cool or damp weather. This is normal and in no way effects the useful
life of the vehicle lighting system.
Adhesive strips for headlights or adjusting headlights
In those countries where vehicles drive on the other side of the road to the
home country, the asymmetric dipped beam may dazzle drivers of oncoming
vehicles. Therefore, when driving abroad, adhesive strips should be attached
to the headlights or the headlights should be adjusted accordingly.
The direction of the headlights can be adjusted from the instrument panel, in
the menu Settings submenu Travel mode Ÿpage 70.
For those vehicles in which it is not possible to adjust the headlights from the
menu, adhesive strips are used to cover certain parts of the headlamp cover
or the headlights may be adjusted at a specialised workshop. For further
information, please refer to a specialised workshop. SEAT recommends
visiting a qualified workshop.
Note
The use of Travel mode and adhesive strips on the headlights is only author-
ised for a short period of time. To modify the direction of the headlamps more
permanently, please take the vehicle to a specialised workshop. SEAT recom-
mends visiting a qualified workshop.
Function “Coming home” and “Leaving home” (guidance
lights)
The “Coming home” function should be switched on manually. However the
“Leaving home” function is automatically controlled by a photo sensor.
Lighting around the exterior mirrors
The lighting around the exterior mirrors illuminates the door area on entering
and leaving the vehicles. It comes on when the vehicle is unlocked, when the
vehicle door is opened and when the “Coming home” or “Leaving home”
“Coming Home”Necessary operations
To switch sys-
tem on:
– Switch off the ignition.
– Briefly flash the headlights for approximately one sec-
ond Ÿpage 115.
The “Coming home” lighting comes on when the driver's
door is opened. The delay in switching off the headlights
is counted from when the last door or tailgate is closed.
The system
switches off:
– Automatically at the end of the delay period.
– Automatically, if 30 seconds after coming on, a vehicle
door or tailgate remains open.
– If the light switch is turned to position
/.
– If the ignition is switched on.
“Leaving home”Necessary operations
To switch sys-
tem on:– Unlock the vehicle when the light switch is in position
!54/ and the photo sensor detects darkness.
The system
switches off:
– Automatically, at the end of the delay period.
– When the vehicle is locked.
– When the light switch is turned to position
/.
– When the ignition is switched on.

Lights and visibility 126
Note
The intermittent wiper speed varies according to the vehicle speed. The faster
the vehicle is moving, the more often the windscreen is cleaned.
Note
The rear wiper is automatically switched on when the windscreen wiper is
connected and the car is in reverse gear.
Windscreen wiper functions
Heated windscreen washer jets
The heating only thaws the frozen jets, it does not thaw the water in the
washer hoses. The heated windscreen washer jets automatically adjust the
heat depending on the ambient temperature, when the ignition is switched
on.Headlight wash /wipe system
The headlight washers/wipers clean the headlight lenses.
After the ignition is switched on, the first and every fifth time the windscreen
washer is switched on, the headlights are also washed. Therefore, the wind-
screen wiper lever should be pulled towards the steering wheel when the
dipped beam or main beam are on. Any incrusted dirt (such as insects)
should be cleaned regularly (e.g. when refuelling).
To ensure the headlight washers work correctly in winter, any snow which has
got into the bumper jet supports should be cleaned away. If necessary,
remove snow with an anti-icing spray.
Note
The wiper will try to wipe away any obstacles that are on the windscreen. The
wiper will stop moving if the obstacle blocks its path. Remove the obstacle
and switch the wiper back on again.Windscreen wiper performance in different situations:
If the vehicle is at a stand-
still:The activated position provisionally changes
to the previous position.
During the automatic wipe:
The air conditioning comes on for approxi-
mately 30 seconds in air recirculation mode
to prevent the smell of the windscreen
washer fluid entering the inside of the vehi-
cle.
For the intermittent wipe:The intervals between wipes vary according
to the speed of the vehicle. The higher the
vehicle speed the shorter the intervals.

Seats and storage compartments153
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xHook in the net partition on the rear right-hand side roof support by
pressing on the rod.
xSecure the hooks of the net partition to the attachment rings in the left
and right hand side foot rests on the second row of seats then tighten the
straps.
Removing the net partition
xLoosen the net partition straps.
xRelease the net partition hooks from the rings Ÿpage 152, fig. 100 .
xRelease the net partition from the right and left roof supports
Ÿpage 152, fig. 100 or by pressing on the rod.
xUnhook the net partition from the left-hand side roof support.
Folding in the net partition
xPress on the release button Ÿpage 152, fig. 99 and bend the rod
in the direction of the arrow with the release o button pressed.
xPress on the release button Ÿpage 152, fig. 99 and bend the rod
in the direction of the arrow with the release button pressed.
xStore the net partition securely in the vehicle.
WARNING
Loose objects in the passenger compartment can be violently thrown in
case of a sudden manoeuvre or braking and especially in accidents causing
serious injury.
xEnsure that the rods are correctly locked in place.
xEven when net partition is correctly fitted, objects must be secured.
xWhen driving with the net partition, no passengers should be behind
it.
Fastening rings
To the front and rear of the luggage compartment, there are fastening rings
for securing objects Ÿfig. 101 (arrows). On some models, the fastening
rings are all the way to the back on the lock carrier plate.
There are other fastening rings located to the left and right hand side of the
second row footrests.
Some models of fastening rings must be lifted to use them.
WARNING
Unsuitable or damaged ropes or straps may be released in case of sudden
braking or an accident. As a result, objects may be fired through the
passenger compartment causing serious injury or death.
xAlways use suitable ropes and straps in good condition.
xSecure the ropes and straps to the fastening rings.
xLoose objects in the luggage compartment can suddenly slide and
change the way the vehicle handles.
AB
AAAC
A2AA
A3AB
Fig. 101 In the luggage
compartment: fastening
rings

Heating, Ventilation and Air conditioning179
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Heating, Ventilation and Air conditioning
Climate Control
Introduction
Viewing Climatronic information
The factory-fitted radio or navigation system screen briefly displays informa-
tion relating to Climatronic.
The units of temperature measurement is displayed on the factory-installed
radio or navigation system and, depending on the vehicle equipment, can be
set using the Configuration menu on the instrument panel.
Additional information and warnings:
xSEAT information system Ÿpage 70
xWindscreen wash system Ÿpage 124
xAuxiliary heating Ÿpage 187
xCaring for and cleaning the vehicle exterior Ÿpage 269
WARNING
Reduced visibility through the windows increases the risk of serious acci-
dents.
xEnsure that all windows are free of ice and snow and that they are not
fogged up preventing a clear view of everything outside.
xThe maximum heat output required to defrost windows quickly is only
available when the engine has reached its normal running temperature.
Only drive when you have good visibility.
xAlways ensure that you use the climate control and heated rear window
to maintain good visibility.
xNever leave the air recirculation on for a long period of time. If the
cooling mode is switched off and air recirculation mode switched on, the
windows can mist over very quickly, considerably limiting visibility.
xSwitch air recirculation mode off when it is not required.
WARNING
Stuffy or used air will increase fatigue and reduce driver concentration
possibly resulting in a serious accident.
xNever leave the fresh air fan turned off or use the air recirculation for
long periods of time; the air inside the passenger compartment will not be
refreshed.
Caution
xSwitch the climate control system off if you think it may be broken. This
will avoid additional damage. Have the climate control system checked by a
qualified workshop.
xRepairs to the climate control system require specialist knowledge and
special tools. SEAT recommends visiting a qualified workshop.
xDo not smoke when air recirculation is switched on in vehicles with a
climate control system. The smoke taken in could lie on the cooling system
vaporiser and on the activated charcoal cartridge of the dust and pollen filter,
leading to a permanently unpleasant smell.
Note
When the cooling system is turned off, air coming from the outside will not be
dried. To avoid fogging up the windows, SEAT recommends leaving the cooler
WARNING (continued)

Heating, Ventilation and Air conditioning 182
Some Climatronic controls may also be on the climate control system control
panel located in the rear centre console. These controls are used to make the
appropriate settings for the rear seats.
Control
button Additional information. Climatic Ÿpage 181, fig. 129; Cli-
matronic Ÿpage 181, fig. 130.
Tem-
perature
ˆ ... ˆ
Climatic: rotate the control to adjust the temperature accord-
ingly.
Climatronic: the settings for the left hand side, the right-hand
side and the rear seats are made separately. Rotate the control
to adjust the temperature accordingly. The temperature is indi-
cated on the outside ring.
Fan
 ... –
Climatic: setting 0, fan and Climatic switched off;
setting 4, fan set to maximum.
Climatronic: the Fan speed is automatically adjusted depend-
ing on the vehicle speed to avoid annoying noises. The fan can
also be adjusted manually.
Air dis-
tributionClimatic: rotate the continuous control to direct the airflow to
the desired area.
Climatronic: manually adjustable using the controls.
<
Climatic: defrost function. The airflow is directed at the wind-
screen. In this position, air recirculation is automatically
switched off or is not switched on.
<
Climatronic: defrost function. The air drawn in from outside the
vehicle is directed at the windscreen and air recirculation is
automatically switched off. To defrost the windscreen more
quickly, the air is dehumidified at temperatures over approxi-
mately +1.5 °C (+35 °F) and the fan runs at maximum output.
KThe air is directed at the chest of driver and passengers by the
dashboard air vents.
L– Air distribution towards the footwell.
A1
A2
A3
qAir distribution towards the windscreen and the footwell.
ACClimatic, Climatronic: Press the button to turn off/on cooling.
=
Heated rear window: this only works when the engine is run-
ning and switches off automatically after a maximum of 10
minutes.
Air recirculation mode Ÿpage 185.
oClimatronic: Automatic air recirculation Ÿpage 185.
pWindscreen heating: only works when the engine is running
and switches off automatically after a few minutes.
>Instant auxiliary heating on/off button Ÿpage 187.
Switching
off
OFFClimatic: turn the fan switch to setting 0.
Climatronic: press the button or set the fan manually to 0.
When the system switches off, the button will light up.
REAR
Climatronic: press the button to adjust the climate con-
trol for the rear seats from the front. The button will light
up when the function is switched on. The settings for the rear
seats will be displayed. Press the button again to switch the
function off or do not touch any other button for around 10
seconds.
Control
button Additional information. Climatic Ÿpage 181, fig. 129; Cli-
matronic Ÿpage 181, fig. 130.
OFF
OFF
REAR
REST