2010 Seat Alhambra ECO mode

Seat belts 16
Seat belts
Brief introduction
Introduction
Check the condition of all the seat belts at regular intervals. If you notice that
the belt webbing, fittings, retractor mechanism or buckle of any of the belts
is damaged, the belt must be replaced immediately by a specialist workshop
Ÿ. The specialist workshop must use the appropriate spare parts corre-
sponding to the vehicle, the equipment and the model year. SEAT recom-
mends visiting a qualified workshop.
Additional information and warnings:
xAdjust the seat position Ÿpage 10
xAirbag system Ÿpage 33
xChild seats (accessories) Ÿpage 42
xIntegrated child seats Ÿpage 52
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Unbuckled or badly buckled seat belts increase the risk of severe or even
fatal injuries. The seat belt cannot offer its full protection if it is not
fastened and used correctly.
xSeats belts are the most effective ways of reducing the risk of
sustaining severe or fatal injuries In the event of an accident. Seat belts
must be correctly fastened when the vehicle is in motion to protect the
driver and all vehicle occupants.
xBefore each trip, every occupant in the vehicle occupants must sit prop-
erly, correctly fasten the seat belt belonging to his or her seat and keep it fastened throughout the trip. This also applies to other occupants when
driving in town.
xWhen travelling, children must be secured in the vehicle with a child
restraint system suitable for their weight and height and with the seat
belts correctly fastened Ÿpage 42.
xInstruct your passengers to fasten their seat belts properly before
driving off.
xInsert the latch plate into the buckle for the appropriate seat and
ensure it is engaged. Using the latch plate in the buckle of another seat will
not protect you properly and may cause severe injuries.
xDo not allow liquids or foreign bodies to enter the buckle fastenings.
This could damage the buckles and seat belts.
xNever unbuckle your seat belt when the vehicle is moving.
xNever allow more than one passenger to share the same seat belt.
xNever hold children or babies on your lap sharing the same seat belt.
xLoose, bulky clothing (such as a jacket) impairs the proper fit and func-
tion of the seat belt.
WARNING
It is extremely dangerous to drive using damaged seat belts and could
result in serious injury or loss of life.
xAvoid damaging the seat belt by jamming it in the door or the seat
mechanism.
xIf the fabric or other parts of the seat belt are damaged, the seat belts
could break in the event of an accident or sudden braking.
WARNING (continued)

Airbag system 38
Side airbags
The side airbags are located in the outer cushion of the driver and front
passenger seat backrests Ÿpage 38, fig. 20. Depending on the equipment
of the model, the outer seats of the second row of seats may also be fitted
with side airbags, located between the seat backrests and the access area. Their position is indicated by the word “AIRBAG”. The red area (dotted line)
Ÿfig. 21 shows the field of action of the side airbags.
Fig. 20 On the side of the
front seat: location of the
side airbag.
Fig. 21 Range of action of the front and rear side
airbags. : with 5 and 7 seats; : with 6 seats.AAAB

Child safety 48
passenger seat to the size of the child seat and the height of the child. Ensure
the passenger is in the correct position ’ Ÿpage 10.
Move the second and third row of seats fully back and lock them. Place the
seat backs in a vertical position and fold the armrests down.
ISOFIX child seats approved for rear seats
The rear seats are suitable for child seats with the ISOFIX system specially
designed for this type of vehicle in accordance with regulation ECE-R 44.
ISOFIX child seats are divided into “specific categories for the vehicle”,
“limited” or “semi-universal”.
Child seat manufacturers supply a list of vehicles with each ISOFIX seat,
which includes the models for which the ISOFIX child seat in question is
approved. If the vehicle is included in the manufacturer's list and the ISOFIX
child seat belongs to a seat category included in the list, then it can be used
in your vehicle. If necessary, contact the child seat manufacturer for an
updated list of vehicles.
WARNING
If child seats are fitted to all the seats in the second row then it is possible
that the seats of this row cannot be folded down from the third row of seats
in case of an accident. In case of an emergency, passengers in the third row
of seats will not be able to leave the vehicle or to help themselves.
xChild seats should not occupy all the seats of the second row if other
passengers are to occupy the third row of seats.
Securing child seats with the seat belt
Securing the child seat using the seat belt
xPlease read and observe the child seat manufacturer's handling instruc-
tions.
xPositioning the child seat on the seat according to the manufacturer's
instructions.
xThe seat belt height adjustment must be as high as possible.
Group (weight
category)ISOFIX child seat
categorySeat position on the
rear seats
Group 0: chil-
dren up to 10 kgEIUFa)
Group 0+: chil-
dren up to 13 kg
EIUFa)
DIUFa)
CIUFa)
Group 1: 9 to 18
kg
DIUFa)
CIUFa)
BIUFa)
B1IUFa)
AIUFa)
a)IUF: suitable for “universal” ISOFIX child seats authorised for use in this group.
Group (weight
category)ISOFIX child seat
categorySeat position on the
rear seats

Cockpit 66
Mileage
The odometer registers the total distance travelled by the car.
The trip recorder (trip) shows the distance travelled since the last trip recorder
reset. The last digit of the trip recorder indicates distances of 100 metres or
tenths of a mile.
Outside temperature display
When the outside temperature is below +4 °C (+39 °F), the symbol “ice
crystal” (warning of risk of freezing) is also displayed next to the temperature.
At first this symbol flashes and then it remains lit until the outside tempera-
ture rises above +6 °C (+43 °F) Ÿ.
When the vehicle is at a standstill, with the parking heating on (Ÿpage 187),
or when travelling at very low speeds, the temperature displayed may be higher than the true outside temperature, as a result of the heat produced by
the engine.
The temperatures measured range from -40 °C to +50 °C (-40 °F to +122 °F).
Compass
With the ignition on and the navigation system on, the cardinal point corre-
sponding to the vehicle's direction of travel is displayed on the instrument
panel Ÿpage 67.
Selector lever positions
The range of engaged gears of the selector lever is shown on the side of the
lever, and on the instrument panel display. In positions D and S, and with the
Tiptronic, the corresponding gear is also displayed.
Recommended gear (manual gearbox)
The recommended gear to save fuel is displayed on the instrument panel
while you are driving Ÿpage 201.
Second speed display (mph or km/h)
In addition to the speedometer, the speed can also be displayed in a different
unit of measurement (in miles or in km per hour). To change the units, in the
Settings menu, select the option Second speed Ÿpage 70.
Vehicles without menu display on the instrument panel
xSwitch on the engine.
xPress button three times. The odometer display flashes on the instru-
ment panel display.
xPress button once. “mph” or “km/h” is displayed briefly instead
of the odometer.
xThis activates the second speed display. To switch it off, repeat the proce-
dure.
This option cannot be disconnected in models destined for countries in which
the second speed must always be visible.
Type of mes-
sageSymbol
colourMeanings
Priority 1
warning.Red
Symbol flashing or lit; partly combined with
audible warnings.
› Stop the vehicle! It is dangerous Ÿ!
Check the function which is faulty and repair.
If necessary, request assistance from special-
ised personnel.
Priority 2
warning.Yellow
Symbol flashing or lit; partly combined with
audible warnings.
A faulty function, or fluids which are below the
correct levels may cause damage to the vehi-
cle! Ÿ
Check the faulty function as soon as possible.
If necessary, request assistance from special-
ised personnel.
Informative
text.–Information relating to different vehicle proc-
esses.
¡
0.0 / SET

Cockpit 68
The compass does not require calibration in vehicles for which the navigation
system was mounted at the factory. The option compass disappears.
The compass in vehicles in which the navigation system was not mounted at
the factory, is permanently and automatically calibrated. If electronic or metal
accessories (mobile phone, television) are subsequently mounted in the
vehicle, the compass should be recalibrated manually.
Adjusting the magnetic zone
xSwitch the ignition on.
xSelect the Settings menu followed by the option Compass and Zone.
xSelect the magnetic zone corresponding to the position of the vehicle
Ÿpage 67, fig. 37.
xAdjust and confirm the magnetic zone (1-15).
Calibrating compass
To calibrate the compass you must be in one of the valid magnetic zones with
sufficient space to be able to trace a circumference with the vehicle.
xSwitch the ignition on.
xSelect the Settings menu followed by the option Compass and Calibrate.
xConfirm the message Describe a complete circumference to calibrate the
compass with and then trace a complete circumference driving at approx-
imately 10 km/h (6 mph).
When the corresponding cardinal point is displayed, the calibration is
complete.
Service interval display
The inspection display appears on the instrument panel Ÿpage 64, fig. 36
.SEAT makes a difference between services with engine oil change (Mainte-
nance Service) and services without engine oil change (Inspection Service).
The service interval display only gives information for service dates which
involve an engine oil change. The dates of the remaining services (for
example, the next Inspection Service or change of brake fluid) are listed on
the label attached to the door strut, or even in the Maintenance Programme.
In vehicles with Services established by time or mileage, the service intervals
are already pre-defined.
In vehicles with LongLife Service, the intervals are determined individually.
Technical progress has made it possible to considerably reduce servicing
requirements. The technology used by SEAT ensures that your vehicle only
has an maintenance service when it is necessary. To establish when the Main-
tenance Service is due (max. 2 years), the vehicle's conditions of use and
individual driving styles are considered. The service pre-warning first appears
20 days before the date established for the corresponding service. The kilo-
metres remaining until the next service are always rounded up to the nearest
100 km and the remaining time is given in complete days. The current service
message cannot be viewed until 500 km after the last service. Prior to this
only lines are visible on the display.
Inspection reminder
When the Service date is approaching, when the ignition is switched on a
Service reminder is displayed.
In vehicles without text messages, a spanner is displayed on the instrument
panel
> with a figure given in km. The number of kilometres shown is the
maximum number that may be driven until the next service. After a few
seconds,the display mode changes. A clock symbol appears and the number
of days until the next service appointment is due.
In vehicles with text messages, Service in --- km or --- days is displayed on the
instrument panel .
OK
A4

Cockpit 70
SEAT information system
Introduction
With the ignition switched on, it is possible to read the different functions of
the display by scrolling through the menus.
In vehicles with a multifunction steering wheel, there are no buttons on the
windscreen wiper lever. The multifunction display can only be controlled from
the buttons on the multifunction steering wheel.
The number of menus displayed on the instrument panel will vary according
to the vehicle electronics and equipment.
A specialised dealer will be able to programme or modify additional func-
tions, according to the vehicle equipment. SEAT recommends visiting a qual-
ified workshop.
Some menu options can only be read when the vehicle is at a standstill.
As long as a priority 1 warning is displayed, it will not be possible to read the
menus. To display the menus, confirm the warning by pressing .
Additional information and warnings:
xExterior mirrors Ÿpage 130
xParking heating Ÿpage 187
WARNING
Any distraction may lead to an accident, with the risk of injury.
xDo not read the instrument panel menus when driving.
Summary of the menu structure
„Multifunction display (MFI) Ÿpage 73
„Journey duration
„Current fuel consumption
„Average fuel consumption
„Distance to empty (the distance you can travel with the remaining fuel)
„Distance covered
„Average speed
„Digital display of speed
„Oil temperature digital display
„Speed warning
„Audio ŸBooklet “Radio” or ŸBooklet “navigation system”
„Navigation ŸBooklet “Navigation system”
„Parking heating Ÿpage 187
„Activation
„On / Off programme
„Switching off
„Timer 1-3
„Day
„Time
„Minute
„Enabling
„Duration
„Operating mode
„Heat
„Ventilation
„Day
OK

Cockpit71
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
„Default setting
„Vehicle condition Ÿpage 73
„Configuration Ÿpage 75
„Multifunction display data
„Journey duration
„Current fuel consumption
„Average fuel consumption
„Distance covered
„Distance to empty (the distance you can travel with the remaining
fuel)
„Average speed
„Digital display of speed
„Speed warning
„Compass
„Convenience Ÿpage 76
„Open door
„Manual
„automatic mode
„Childproof locks On / Off
„Anti-theft alarm confirmation On / Off
„Handling windows
„Off
„All
„Driver
„Mirror adjustment On / Off
„Rear-view mirror adjustment
„Synchronised
„Individual
„Default setting
„Lights & visibility Ÿpage 77
„Coming Home
„Leaving Home
„Footwell light
„Convenience indicators On / Off
„Default setting
„Time
„Winter tyres
„Settings: Language
„Units
„Second speed display On / Off
„Autohold
„Travel mode On / Off
„Service
„Info
„Reset
„Default setting

Cockpit73
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Main menuMFI display menu
The multifunction display (MFI) has two automatic memories: 1 - Partial
memory and 2 - Total memory. The selected memory will be shown in the
upper right-hand corner of the display.MenuFunctionSee
MFIInformation and possible configurations of the
multifunction display (MFI).Ÿpage 73
Audio
If the radio is on, the station is displayed.
In CD mode, the current CD is played.
ŸBooklet
“Radio” or
ŸBooklet
“navigation
system”
NavigationNavigation system information:
when the navigation to destination is on,
change of direction arrows and a proximity bar
are displayed. These symbols are similar to
those used in the navigation system.
If navigation to destination is not on, the direc-
tion of travel (compass) and the name of the
street on which you are driving are displayed.ŸBooklet
“Navigation
system”
Parking
heatingInformation and configurations of the parking
heating:
switching the parking heating on or off. Select
the operating mode and duration.Ÿpage 187
Vehicle
conditionCurrent warning or information texts.
This option only appears when one of the fol-
lowing texts is available. The number of availa-
ble messages is displayed. Example 1/1 or
2/2.Ÿpage 64
SettingsDifferent setting options, for example, the Con-
venience, Lighting & or Visibility menus, and
the time, speed warning with winter tyres, lan-
guage, units of measurement, or “Display off”.Ÿpage 75
With the ignition switched on, and memory 1 or 2 displayed, briefly press
to change from one memory to another.
1
Trip mem-
ory (for a
single jour-
ney).
The memory stores the values for the journey and the con-
sumption from the moment the ignition is switched on until
it is switched off again.
If the journey is broken for more than two hours, the mem-
ory is automatically erased. If the journey is continued in
less than two hours after the ignition is switched off, the
new data is added to the data already stored in the mem-
ory.
2Total mem-
ory (for all
journeys).
The memory records the values for a specific number of
partial trips, up to a total of 19 hours and 59 minutes or 99
hours and 59 minutes, or 1999.9 km (or miles) for 9999 km
(or miles), depending on the model of instrument panel.
On reaching either of these limits, the memory is automati-
cally erased and starts to count from 0 again.
OK