2010 Seat Alhambra esp

If and when347
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
First aid kit, warning triangle, reflective vests and fire
extinguishers
Reflective vests
Some vehicles will have a driver's door compartment to store a reflective vest
Ÿpage 59.
Warning triangle
With the tailgate open, rotate the lock Ÿfig. 196 90°. Lower the bracket and
remove the warning triangle.
First-aid kit
There is a first aid kit Ÿpage 162 in the rear left-hand side storage compart-
ment of the luggage compartment.
The first aid kit must comply with legal requirements. Check the expiry date
of the contents of the first aid kit.
Fire extinguisher
There is a Fire extinguisher underneath the passenger seat.The fire extinguisher must conform to legal requirements, be ready for use
and be checked regularly. Check the certification seal on the extinguisher.
WARNING
Loose objects in the passenger compartment can be violently thrown in
case of a sudden manoeuvre or braking and especially in accidents causing
serious injury.
xSecure fire extinguishers, first aid kit, reflective vests and warning
triangle securely to their respective supports.
Fig. 196 On the boot lid:
Warning triangle bracket.

If and when353
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
To o l s *
Introduction
When securing the vehicle in case of a breakdown, please note the legal
requirements for each country.
Additional information and warnings:
xWorking in the engine compartment Ÿpage 304
xChange wheel Ÿpage 339
xIn case of emergency Ÿpage 345
WARNING
Loose objects in the passenger compartment can be violently fired through
the compartment in case of a sudden manoeuvre or braking and especially
in accidents causing serious injury.
xMake sure that the vehicle tools are stored safely in the luggage
compartment.
WARNING
Unsuitable or damaged on-board tools can cause injury or accidents.
xNever work with inappropriate or damaged tools.
Location
Depending on the model, the vehicle tools may be kept in the luggage
compartment, in a cavity close to the lock carrier Ÿfig. 206. Loosen the
safety straps and remove the on-board tools. For vehicles factory-fitted with
winter tyres, you will find additional tools in a toolbox located in the luggage
compartment.
Note
After use, return the jack to its initial position using the handle in order to
securely store it in the vehicle.
Fig. 206 In the luggage
compartment, viewed
from inside the vehicle:
On-board tools are
located in a cavity close to
the lock carrier.

If and when 358
Caution
xAlways carefully remove the fuse box covers and refit them correctly to
avoid problems with your vehicle.
xProtect the fuse boxes when open to avoid the entry of dust or humidity.
Dirt and humidity inside fuse boxes can cause damage to the electrical
system.
Note
In the vehicle, there are more fuses than those indicated in this chapter.
These should only be changed by a specialist workshop.
Replacing a blown fusePreparation
xSwitch off the ignition, lights and all electrical equipment.
xOpen the corresponding fuse box Ÿpage 357
Identifying a blown fuse
A fuse is blown if its metal strip is ruptured Ÿfig. 211.
Point a lamp at the fuse. This will make it easier to see if the fuse is blown.
To replace a fuse
xIf necessary, remove the plastic pincers from the fuse box cover.
xFor small fuses, insert the pincers from above Ÿfig. 212 .
xFor larger fuses, insert the pincers from one side of the fuse Ÿfig. 212
.
xRemove the relevant fuse.
xReplace the blown fuse by one with an identical amperage rating (same
colour and markings) and identical size Ÿ.
xReplace the cover.
Fig. 211 Image of a
blown fuse.
Fig. 212 Removing or
fitting a fuse.
AA
AB

If and when 360
Changing bulbs
Introduction
Changing bulbs requires a certain amount of manual skill. If you are unsure,
SEAT recommends that you consult an qualified workshop or request assist-
ance from a specialist. In general, a specialist is required if other vehicle
components must be removed or if the discharge lamps must be replaced.
You should store spare light bulbs in the vehicle for safety-relevant lights.
Spare bulbs may be obtained from the Official dealers and workshops. In
some countries, it is a legal requirement to carry spare bulbs in the vehicle.
Driving with faults and blown bulbs on the vehicle exterior lighting is against
the law.
Additional bulb specifications
The specifications of some headlamp bulbs and bulbs for the tail lamps fitted
at the factory may be different to those of conventional bulbs. Bulb informa-
tion is displayed on the bulb socket or on the bulb itself.
Additional information and warnings:
xLights and visibility Ÿpage 113
xWorking in the engine compartment Ÿpage 304
xVehicle tools Ÿpage 353
xFuses Ÿpage 356
WARNING
If the road is not well-lit and the vehicle is not clearly visible to other
drivers, there is a risk of accident.
WARNING
Failure to replace bulbs correctly may cause serious accidents.
xBefore carrying out any work in the engine compartment please read
and observe the warnings Ÿpage 304. In any vehicle, the engine compart-
ment is a hazardous area and could cause severe injury.
xDischarge lamps work with high-voltage and can cause serious or fatal
injury if handled incorrectly.
xH7 and discharge lamps are highly pressurised and could explode
when being changed.
xOnly replace the bulbs concerned when they have cooled.
xNever replace bulbs alone if you are not familiar with the operations
necessary. If you are not sure about procedures then visit a qualified work-
shop to carry out the necessary work.
xNever touch the bulb glass directly. Fingerprints will be evaporated by
the heat of the operating bulb thus “fogging” up the reflector.
xThe headlamp frameworks in the engine compartment and the tail
lamps contain sharp elements. Always protect your hands when changing
bulbs.
Caution
After changing a bulb, if the rubber covers and plastic caps are not replaced
correctly on the headlamp framework, the electrical installation may be
damaged, especially if water is allowed to enter.

If and when361
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Indicator
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Checking the bulbs of a trailer
For vehicles with the factory fitted trailer system, certain trailer lights are also
controlled if the socket is correctly connected.
A fault on a trailer turn indicator is indicated on the instrument panel by the
indicator blinking twice as fast (
 or
) Ÿpage 113.
xGeneral fault of all indicators on one side.
xFault in one tail light (on some models, also the registration light).
xFault in two brake lights.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Note
A fault in the LED on the tail lights will not be indicated. However, if the fault
affects all the LEDs then this will be indicated by the indicator .
Information for replacing bulbs
Checklist
To replace a bulb, carry out the following operations always in the order given
Ÿ:
1. Park the vehicle a safe distance from traffic and on suitable ground.
2. Connect the electronic parking brake Ÿpage 210.
3. Turn the light switch to position 0 Ÿpage 113.
4. Move the gear lever into the neutral position Ÿpage 113.
5. Automatic gearbox: Move selector lever to position P Ÿpage 201.
6. Stop the engine and remove the key from the ignition Ÿpage 195.
7. Manual gearbox: Select a gear Ÿpage 201.
8. Wait until all of the passenger compartment lights are turned off
Ÿpage 113.
9. Allow the corresponding bulb to cool.
10. Visually inspect fuses to see if any are blown Ÿpage 356.
11. Replace the bulb according to the instructions Ÿ. Bulbs should only
be replaced by new identical models. Bulb information is displayed on
the bulb socket or on the bulb itself.
12. In general, never touch the bulb glass directly. The heat of the bulb would
cause the fingerprint to evaporate and condense on the reflector. This
will impair the brightness of the headlight.
lights upPossible causeSolution
A vehicle exterior lighting
bulb is not working.Replace the faulty bulb.

If and when375
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Towing and tow starting
Introduction
When towing, always respect legal requirements.
For technical reasons, it is not possible to tow a vehicle if the battery is flat.
Additional information and warnings:
xElectronic power control and exhaust gases purification system
Ÿpage 255
WARNING
A vehicle with a flat battery should never be towed.
xNever remove the key from the ignition lock. The electronic steering
lock could engage. Then the vehicle will be uncontrollable. You may lose
control of the vehicle and there is a risk of serious accident.
WARNING
When towing the vehicle, the handling and braking efficiency change
considerably. Please observe the following instructions to minimise the
risk of serious accidents and injury:
xAs the driver of the vehicle being towed:
The brake must be depressed must harder as the brake servo does
not operate. Always remain aware to avoid collision with the towing
vehicle.
More strength is required at the steering wheel as the power
steering does not operate when the engine is switched off.
xAs the driver of the towing vehicle:
Accelerate gently and carefully.Avoid sudden braking and manoeuvres.
Brake well in advance than usual and brake gently.
Caution
xCarefully fit and remove the towing ring and its cover to avoid damage to
the vehicle (for example, paintwork).
xWhen towing, fuel could enter the catalytic converter and cause
damage!
Instructions for tow starting
In general, the vehicle should not be started by towing. Jump-starting is
much more preferable Ÿpage 371.
For technical reasons, the following vehicles can not be tow started:
xVehicles with an automatic gearbox.
xVehicles with the KESSY locking and ignition system, given that the elec-
tronic steering lock will certainly not be unlocked.
xVehicles with an electronic parking brake, given that it is possible that the
brake will not be disengaged.
xIf the vehicle battery is flat, it is possible that the engine control units do
not operate correctly.
However, if your vehicle must absolutely be tow-started (manual gearbox):
xEngage 2nd or 3rd gear.
xKeep the clutch pressed down.
xSwitch on the ignition and the hazard warning lights.
xRelease the clutch when both vehicles are moving.
WARNING (continued)

If and when 378
xScrew in the tow ring into its position anticlockwise as far as it will go
Ÿ. Use a suitable tool to firmly tighten the tow ring in its location.
xAfter towing, remove the tow ring by turning it clockwise and put the cover
back in place.
Caution
xThe tow ring must always be completely and firmly tightened. Otherwise,
it could be released while towing and tow-starting.
xVehicles with a factory fitted towing device, can only be used for towing
with a tow-bar, specially designed to fit on a tow hitch ball. Otherwise, the tow
hitch ball and the vehicle may be damaged. Otherwise, a tow rope should be
used.
Towing advice
Towing requires some experience, especially when using a tow-rope. Both
drivers should be familiar with the technique required for towing. For this
reason, inexperienced drivers should abstain.
While driving, avoid excessive traction forces and jerking. When towing on an
unpaved road, there is always a risk of overloading and damaging the
anchorage points.
If the vehicle is towed, with the hazard warning lights on and the ignition
switched on, the turn signal may be used to indicate changes of direction.
Simply operate the turn indicator lever as usual. Meanwhile, the hazard
warning lights will go off. When the turn signal lever is returned to the rest
position, the hazard warning lights will be turned on automatically.
Notes for the driver of the towed vehicle
xLeave the ignition on to avoid locking the steering wheel, to release the
electronic parking brake and to activate the turn signal indicators, the horn
as well as the window wipers and window washers.
xAs the power assisted steering does not work if the engine is not running,
you will need more strength to steer than normally.
xThe brake must be depressed must harder as the brake servo does not
operate. Avoid hitting the towing vehicle.
xNote the instructions and information contained in the instruction manual
for the vehicle to be towed.
Notes for the driver of the towing vehicle
xAccelerate gently and carefully. Avoid sudden manoeuvres.
xBrake well in advance than usual and brake gently.
xNote the instructions and information contained in the instruction manual
for the vehicle to be towed.

General notes on the technical data 382
Towing a trailer
Trailer weights
Trailer weight
The trailer weights and drawbar loads approved are selected in intensive
trials according to precisely defined criteria. The approved trailer weights are
valid for vehicles in the EU for maximum speeds of 80 km/h (in certain
circumstances up to 100 km/h). The figures may be different in other coun-
tries. All data in the official vehicle documents take precedence over these
data Ÿ.
Drawbar load
The maximum permitted weight exerted by the trailer drawbar on the ball joint
of the towing bracket must not exceed 85 kg.
In the interest of road safety, we recommend that you always tow
approaching the maximum drawbar load. The response of the trailer on the
road will be poor if the drawbar load is too small.
If the maximum permitted drawbar load is not reached (e.g. in the case of
small single-axle trailers, light and without load, or tandem axle trailers with
a wheelbase of less than 1 m) it is compulsory for the drawbar load to be at
least 4% of the trailer's weight.
WARNING
xFor safety reasons, do not exceed the 80 km/h limit. This is also valid in
countries where higher speeds are permitted.
xNever exceed the maximum trailer weights or the drawbar load. If the
permissible axle load or the permissible total weight is exceeded, the
driving characteristics of the vehicle may change, leading to accidents,
injuries and damage to the vehicle.
Wheels
Tyre pressure, snow chains, wheel bolts
Tyre pressures
The sticker with the tyre pressure values can be found on the inside of the
tank flap. The tyre pressure values given there are for cold tyres. The slightly
raised pressures of warm tyres must not be reduced. Ÿ
Snow chains
Snow chains may be fitted only to the front wheels.
Consult the chapter “wheels” of this manual.
Wheel bolts
After the wheels have been changed, the tightening torque of the wheel bolts
should be checked as soon as possible with a torque wrench Ÿ. The tight-
ening torque for steel and alloy wheels is 120 Nm.
WARNING
xCheck the tyre pressure at least once per month. Checking tyre pressure
value is very important. If the tyre pressure is too high or too low, there is
an increased danger of accidents, particularly at high speeds.
xIf the torque of the wheel bolts is too low, they could loosen while the
vehicle is in motion. Risk of accident! If the tightening torque is too high,
the wheel bolts and threads can be damaged.
Note
We recommend that you ask your Authorised Service Centre for information
about appropriate wheel, tyre and snow chain size.