2010 RENAULT SCENIC ESP

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-77
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-77V9 MR-372-J84-17B050$376.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF099
PRESENT
OR
STORED
AUTOMATIC TRANSMISSION OR SEQUENTIAL GEARBOX
CONNECTION VIA THE MULTIPLEX NETWORK
1.DEF: Inconsistency of the signal
2.DEF: Multiplex line connection fault
3.DEF: Gear ratio
4.DEF: Non-compliance with emission control standards
NOTESPriority when dealing with a number of faults:
Deal with faults DF046 Battery voltage or DF084 Actuator relay control circuit first
if they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present with the engine running.
Run a multiplex network test (See88B, Multiplex).
If the fault is still present, run fault finding on the Automatic gearbox system (see23A, Automatic gearbox).
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
S3000_V4C_DF099/S3000_V54_DF099

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-78
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-78V9 MR-372-J84-17B050$376.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF101
PRESENT
OR
STOREDMULTIPLEX ELECTRONIC STABILITY PROGRAM LINK
1.DEF: Multiplex line connection fault
NOTESNone.
Run a multiplex network test (see88B, Multiplexing).
If the fault is still present, carry out fault finding on the ABS - ESP system (see38C, Anti-lock braking system).
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
S3000_V4C_DF101/S3000_V54_DF101

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-82
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-82V9 MR-372-J84-17B050$376.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF109
PRESENT
OR
STOREDLOW FUEL LEVEL MISFIRING
1.DEF: Destructive misfiring
2.DEF: Polluting misfiring
3.DEF: Non-compliance with emission control standards
NOTESPriority when dealing with a number of faults:
– fuel supply circuit:
DF085 Fuel pump relay control circuit,
DF026 Injector control circuit cylinder 1,
DF027 Injector control circuit cylinder 2,
DF028 Injector control circuit cylinder 3,
DF029 Injector control circuit cylinder 4
– combustion misfiring:
DF059 Combustion misfire in cylinder 1,
DF060 Combustion misfire in cylinder 2,
DF061 Combustion misfire in cylinder 3,
DF062 Combustion misfire in cylinder 4.
Conditions for applying the fault finding procedure to stored faults:
The fault is present after starting the engine and under the following conditions:
– there must be no further electrical faults,
– programming must be carried out.
– warm engine (coolant temperature 75°C minimum),
– engine running with electrical consumers on for 15 minutes.
Special note:
–OBD warning light illuminated.
Check the presence and conformity of the fuel in the tank.
If there is no present or stored combustion misfire fault, the misfire was caused by the low fuel level.
Clear fault DF109.
AFTER REPAIREnsure that all the faults have been dealt with.
Do not clear the programming.
To check that the system has been repaired correctly:
– there must be no further electrical faults,
– programming has been carried out,
– warm engine (minimum 75°C).
– running at idle speed with all electrical consumers drawing power for 15 minutes.
If the fault reappears, continue the fault finding procedure.
S3000_V4C_DF109/S3000_V54_DF109

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-83
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-83V9 MR-372-J84-17B050$376.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF119
PRESENT
OR
STORED
CAMSHAFT SENSOR SIGNAL
1.DEF: Camshaft tooth event
2.DEF: Measurement of the offset outside permitted range of values
3.DEF: Tooth lost
4.DEF: Non-compliance with emission control standards
5.DEF: Programming the stops
6.DEF: Programming the initial stops
NOTESPriority when dealing with a number of faults:
Apply the procedure for dealing with faults DF046 Battery voltage or DF084
Actuators relay control circuit first if they are present or stored.
If faults DF119, DF154 Flywheel signal sensor circuit and DF080 Camshaft
dephaser circuit are present, ignore DF080 and deal with the other 2 faults first.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
Special note:
–K4M only.
– possibility of a slight lowering in performance
Check the cleanliness and condition of the camshaft sensor connections.
Check the cleanliness and condition of the camshaft sensor.
Repair if necessary.
If the fault is still present, check (with the ignition on) for + 12 V on track 3 of the camshaft sensor.
Check the insulation, continuity and the absence of interference resistance between the following
connections:
Injection computer, connectorB, track M2 track 3 of the camshaft sensor
Protection and Switching Unit, connectorCN,
track 2
Repair if necessary.
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
S3000_V4C_DF119/S3000_V54_DF119

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-88
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-88V9 MR-372-J84-17B050$376.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF154
PRESENT
OR
STOREDFLYWHEEL SIGNAL SENSOR CIRCUIT
1.DEF: Abnormal voltage
2.DEF: Tooth lost
3.DEF: Non-compliance with emission control standards
NOTESPriority when dealing with a number of faults:
If faults DF154, DF119 Camshaft sensor circuit and DF080 Camshaft dephaser
circuit are present, ignore DF080 and deal with the other 2 faults first.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the starter motor has been running for 10 seconds
or at an engine speed above 600 rpm.
Special note:
–the OBD warning light is lit,
– In the event of flywheel signal loss, the injection and ignition are cut off: the vehicle
stalls and cannot be restarted.
1.DEF
NOTESNone.
Check the cleanliness, condition and the fitting of the flywheel.
Repair if necessary.
If the flywheel has been replaced or removed, the flywheel target has to be reinitialised, then reprogrammed.
Programming reinitialisation:
Use command RZ005: Programming.
Carrying out the flywheel target programming:
– Decelerate a first time with injection cut-off (i.e. feet off the brake, accelerator pedal and clutch pedals) between
3500 and 3000 rpm, in 3rd gear for a manual gearbox and 2nd for automatic gearbox, for at least 5 seconds.
– Decelerate a second time with injection cut-off (i.e. brake, accelerator and clutch pedals released) between
2400and 2000 rpm for K4 engines and between 1800 and
1400 rpm for F4R engines, in 3rd gear for a manual gearbox and 2nd for an automatic gearbox, for at least
5 seconds.
After the operation, check that status ET089 Flywheel target programming is COMPLETED.
(*This is the moment when, during deceleration with no load, the engine drops to idle speed and recovers torque).
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
S3000_V4C_DF154/S3000_V54_DF154

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-90
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-90V9 MR-372-J84-17B050$376.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF196
PRESENT
OR
STOREDPEDAL SENSOR CIRCUIT GANG 1
CO.0: Open circuit or short circuit to earth
1.DEF: Inconsistency
2.DEF: Component in bad condition
NOTESPriority when dealing with a number of faults:
Deal with fault DF012 Sensor feed no. 2 voltage first, if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the accelerator pedal changes from no load to full
load.
Special note:
–severity 1 fault warning light illuminated.
CO/CO.0/CC.1: defect mode type 4: speed limiter at 54 mph (90 km/h) and loss of
power during acceleration (pedal feels soft).
1.DEF: defect modes type 3 and 4: regulation of pedal's engine or vehicle speed
setpoint, speed limiter at 54mph (90 km/h) and loss of power during acceleration
(pedal feels soft).
Check that the pedal mechanism has not seized.
Check the cleanliness and condition of the pedal potentiometer connections.
Disconnect the battery and the injection computer.
Check the cleanliness and condition of the connections.
Repair if necessary.
Use the "Universal bornier" to check the insulation and continuity of the following connections:
Injection computer, connectorA, track H3 track 5 of the pedal potentiometer gang 1
Injection computer, connectorA, track G2 track 3 of the pedal potentiometer gang 1
Injection computer, connectorA, track H2 track 4 of the pedal potentiometer gang 1
Repair if necessary.
Measure the resistance of the pedal sensor gang 1 between tracks 4 and 2.
Replace the accelerator potentiometer if the resistance is not 1.7 kΩ ± 0.9 kΩ.
If necessary replace the sensor.
If the fault is still present, contact the Techline.
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
S3000_V4C_DF196/S3000_V54_DF196

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-91
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-91V9 MR-372-J84-17B050$376.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF198
PRESENT
OR
STOREDPEDAL SENSOR CIRCUIT GANG 2
CO.0: Open circuit or short circuit to earth
CC.1: Short-circuit to + 12 V
NOTESPriority when dealing with a number of faults:
Deal with fault DF011 Sensor supply voltage no. 1 first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the accelerator pedal changes from no load to full
load.
Special note:
–level 1 or 2 fault warning light lit,
– defect mode types 3 and 4: regulation of pedal's engine or vehicle speed setpoint,
speed limiter at 54mph (90 km/h) and loss of power during acceleration (pedal feels
soft).
Check that the pedal mechanism has not seized.
Check the cleanliness and condition of the pedal potentiometer connections.
Disconnect the battery and the injection computer.
Check the cleanliness and condition of the connections.
Repair if necessary.
Use the "Universal bornier" to check the insulation and continuity of the following connections:
Injection computer, connectorA, track F4 track 6 of the pedal potentiometer gang 2
Injection computer, connectorA, track F2 track 2 of the pedal potentiometer gang 2
Injection computer, connectorA, track F3 track 1 of the pedal potentiometer gang 2
Repair if necessary.
Measure the pedal sensor resistance gang 2 between tracks 6 and 1.
Replace the accelerator potentiometer if the resistance is not 2.8 kΩ±2.05kΩ.
If necessary replace the sensor.
If the fault is still present, contact the Techline.
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
S3000_V4C_DF198/S3000_V54_DF198

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-92
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-92V9 MR-372-J84-17B050$376.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF228
PRESENT
OR
STOREDBRAKE SIGNALS
1.DEF: Component in bad condition
2.DEF: Non-compliance with emission control standards
NOTESSpecial note:
– cruise control and speed limiter deactivated.
Check:
– the consistency of statuses ET704 Brake switch no. 1 and ET705 Brake switch no. 2 changes to ACTIVE/
INACTIVE,
–the condition and cleanliness of the brake lights switch.
Disconnect the battery and the injection computer, check the condition and cleanliness of the connections.
Check the insulation and continuity of the following connection:
Injection computer, connectorA, track E4 track 3 of the brake light switch
Repair if necessary.
Run a multiplex network test (see88B, Multiplexing).
If the fault is still present, carry out fault finding on the ABS - ESP system (see38C, Anti-lock braking system).
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
S3000_V4C_DF228/S3000_V54_DF228