2010 RENAULT SCENIC ESP

PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-117
PETROL INJECTION
Fault finding - Interpretation of faults
17B
17B-117V9 MR-372-J84-17B050$423.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DF650
PRESENT
OR
STOREDACCELERATOR PEDAL POSITION SIGNAL
1.DEF: Inconsistency of the signal
NOTESPriority when dealing with a number of faults:
Apply the procedure for dealing with faults DF012 Sensor supply voltage no. 2,
DF012 Sensor supply voltage no. 2, DF197 Pedal sensor circuit gang 1, DF198
Pedal sensor circuit gang 2 if these are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when brake and accelerator pedals are depressed
simultaneously for 30 seconds.
Special note:
–Severity 2 fault warning light illuminated,
– defect mode types 3 and 4.
1.DEF
NOTESSpecial note:
–types 2 and 3 defect modes: vehicle and engine speed
restriction, ESP and cruise control/speed limiter are
deactivated.
Check that the accelerator pedal is not jammed and that nothing is impairing its operation (floor carpet, etc.).
Check the connection and condition of the 6-track connector for the accelerator pedal potentiometer.
Repair if necessary.
Check the connection and condition of computer connector A.
Repair if necessary.
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
S3000_V4C_DF650/S3000_V54_DF650

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 170
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 170V9 MR-372-J84-17B050$611.mif

S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54PETROL INJECTION
Fault finding - Interpretation of statuses
ET042
CRUISE CONTROL/SPEED LIMITER
NOTESSpecial notes:
Only perform the tests if the statuses do not correspond with the system programming
functions.
NOT DETECTEDIf the vehicle does not have buttons for the cruise control or speed limiter functions,
status ET042 is permanently NOT DETECTED. Confirmation of the absence of the
cruise control or speed limiter function on the vehicle.
If the vehicle is fitted with cruise control or speed limiter function buttons, the main switch
is in rest (or neutral) position and the injection computer has been programmed or
reprogrammed, status ET042 is NOT DETECTED.
To activate the cruise control or speed limiter function, press the main switch in the
cruise control position and then in the speed limiter position.
Return to rest position.
The tool displays status ET042: "INACTIVE".
If not, several steps must be checked:
1. Return to the page on testing the multiplex network with the CLIP application. Repeat
the multiplex network test. Re-establish dialogue with the injection computer. Check
status ET042. If ET042 is INACTIVE, the injection computer has detected the various
positions of the main switch. The cruise control/speed limiter is active.
2. If ET042 is NOT DETECTED, check that the owner of the vehicle has not at some
point in the past, asked for the cruise control/speed limiter to be disabled. Contact the
Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
S3000_V4C_ET042/S3000_V54_ET042
MR-372-J84-17B050$611.mif

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 171
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 171V9 MR-372-J84-17B050$611.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
ET042
(CONTINUED 1)
INACTIVEWhen the main switch is in the rest (or neutral) position, status ET042 is INACTIVE.
If "CRUISE CONTROL" or "SPEED LIMITER" appears despite the main button being in
the rest position (or neutral), carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for + 12 V APC on the main switch connector.
Disconnect the main switch and with it in the rest position, check the insulation
between:
Injection computer A black,
●32-track track A2 Cruise control On/Off button, 6-track
connector track A3
●32-track track C3 Speed limiter On/Off button, 6-track
connector track B1
– Check the continuity between track C3 (injection computer, connector A, black) and
the speed limiter On/Off button 6-track connector track B1 in the speed limiter
position.
– Check the continuity between track A2 (injection computer, connector A, black) and
the cruise control On/Off button 6-track connector track A3 in the cruise control
position.
If these checks are not in order, replace the switch.
Check the continuity, insulation and the absence of interference resistance on the
following connections: Injection computer connector A, black,
●32-track track A2 Cruise control On/Off button, 6-track
connector track A3
●32-track track C3 Speed limiter On/Off button, 6-track
connector track B1
Repair if necessary.
Check the engine management computer connections.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 185
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 185V9 MR-372-J84-17B050$611.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
ET405
CLUTCH PEDAL SWITCH
NOTESSpecial note:
Only perform the tests if the statuses do not correspond with the system programming
functions.
ACTIVECheck the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch then check the insulation between tracks 1 and 2, with
the switch in the rest position.
Repeat this operation with the switch pressed and check the continuity between tracks
1 and 2.
If these two checks are not in order, replace the switch.
INACTIVECheck the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch then check the insulation between tracks 1 and 2, with
the switch in the rest position.
Repeat this operation with the switch pressed and check the continuity between tracks
1 and 2.
If these two checks are not in order, replace the switch.
Then check the continuity and make sure there is no interference resistance
on the following connection:
Injection computer connector A, black, 32-track, track C4 Track 1 clutch
connector
Check for earth on track 2 of the clutch switch connector.
If there is a repair method (see Technical Note 6015A, Electrical wiring repair,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
S3000_V4C_ET405/S3000_V54_ET405

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 186
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 186V9 MR-372-J84-17B050$611.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
ET415
CRUISE CONTROL/SPEED LIMITER DEACTIVATION
NOTESSpecial notes:
Only perform the tests if the statuses do not correspond with the system programming
functions.
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 displays the various reasons for deactivation of the cruise control/speed limiter function, which are
due to driver demand or the exterior environment.
IMPORTANT
Clear the fault memory by running command RZ001 "Fault memory", to reset this status to "NONE".
NONEThis status is present on the diagnostic tool when:
The computer has been reinitialised.
The computer has been reprogrammed
STATUS 1Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving with the cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and traction control is requested.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If status ET415 becomes STATUS 1 with no traction control request (see 38C, Anti-lock
Braking System).
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool
S3000_V4C_ET415/S3000_V54_ET415

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 187
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 187V9 MR-372-J84-17B050$611.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
ET415
(CONTINUED 1)
STATUS 2Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2 when driving with cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If status ET415 becomes STATUS 2 without depressing the brake pedal, consult the
interpretation of statuses ET704 Brake switch no. 1 and ET705 Brake switch no. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to the engine
(clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation to
the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing)
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated whenever the suspend button is
pressed.
Status ET415 becomes STATUS 4 while driving when:
- Either the cruise control is active.
- Or the speed limiter is active,
- and the driver presses the 0 button.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703 Cruise control/speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 195
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 195V9 MR-372-J84-17B050$611.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
ET566
TYPE 3 DEFECT MODE
NOTESThere must be no present or stored faults.
This status groups the faults for deducing that the system no longer responds to engine or vehicle speed regulation,
but still controls the air flow modulation (throttle servo system operational). It uses the pedal mode reconstructed
by calibration.
AFTER REPAIRRepeat the conformity check from the start.
S3000_V4C_ET566/S3000_V54_ET566

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 198
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 198V9 MR-372-J84-17B050$611.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
ET703
CRUISE CONTROL/SPEED LIMITER BUTTONS
NOTESSpecial notes:
Only perform the tests if the statuses do not correspond with the system programming
functions.
INACTIVEStatus ET703 becomes "INACTIVE" when none of the cruise control/speed limiter
buttons is pressed. These buttons are located on the steering wheel.
If status ET703 does not display "INACTIVE",
●check the condition of the cruise control/speed limiter +/- button and the condition of
its connector,
●check the condition of the cruise control/speed limiter R/0 button and the condition of
its connector.
INCREASEStatus ET703 becomes PLUS when the cruise control/speed limiter + button is pressed.
This button is on the steering wheel, on the left-hand side.
If status ET703 does not display PLUS, check the condition of the cruise control/speed
limiter +/- button, and the condition of its connector. Repair if necessary.
To carry out these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR 364 Mechanical, 88C,
Airbag and seat belt pretensioners, Driver's front airbag, Removal - Refitting)
Measure the resistance on the following connection with the "+" button pressed:
Injection computer,
connector A, black, 32-track track D2 "+/-" button track 2.
connector A, black, 32-track track D3 "+/-" button track 1.
If the resistance is not approximately 300 Ω, check the continuity of the connection when
the button is not pressed.
If there is continuity, replace the +/- control button.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
S3000_V4C_ET703/S3000_V54_ET703