Page 65 of 107
i
69
CRUISE CONTROL
System which automatically maintains
the speed of the vehicle at the value
programmed by the driver, without any
action on the accelerator pedal.
The cruise control is switched on
manually: it requires a minimum vehicle
speed of 25 mph (40 km/h) and the en-
gaging of fourth gear.
The cruise control is switched off man-
ually or by pressing the brake or clutch
pedal or on triggering of the ESP sys-
tem for safety reasons.
It is possible to exceed the programmed
speed temporarily by pressing the ac-
celerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value. The controls of this system are grouped
together on stalk
A .
1. Cruise control mode selection dial
2. Speed programming/value decrease
button
3. Speed programming/value increase
button
4. Cruise control off/resume button The programmed information is grouped
together on the instrument panel dis-
play.
5. Cruise control off/resume indication
6. Cruise control mode selection indi-
cation
7. Programmed speed value
Steering mounted controls Displays on the instrumen
t panel
The cruise control cannot, in any
circumstances, replace the need to
respect speed limits, nor can it re-
place the need for vigilance and re-
sponsibility on the part of the driver.
You are advised to keep your feet
near the pedals.
Page 66 of 107
!
70
Programming
Turn dial 1 to the "CRUISE" po-
sition: the cruise control mode is
selected but is not switched on
(OFF).
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed
s p e e d r e s u l t s i n fl a s h i n g o f t h i s s p e e d o n t h e d i s p l a y .
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically ca n-
c e l s t h e fl a s h i n g o f t h e s p e e d .
Return to normal driving
Turn dial 1 to the "0" position: the cruise control mode is
deselected. The display returns to the distance rec order.
Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
(e.g.: 70 mph (110 km/h)).
Switch off the cruise control by pressing button 4 : the
d i s p l a y c o n fi r m s t h a t i t h a s b e e n s w i t c h e d o f f ( O F F ) .
Switch the cruise control back on by pressing button 4
again.
You can then change the programmed speed using but
tons 2
and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press. Operating fault
In the event of a cruise control malfunc-
tion, the speed is cleared resulting in
fl a s h i n g o f t h e d a s h e s .
Have it checked by a PEUGEOT dealer.
When the cruise control is switched
on, be careful if you maintain the
pressure on one of the programmed
speed changing buttons: this may
result in a very rapid change in the
speed of your vehicle.
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f fi c .
On a steep descent, the cruise
control will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is posi-tioned correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o - ther.
Page 67 of 107
71
SPEED LIMITER
System which prevents the vehicle from
exceeding the speed programmed by
the driver.
When the programmed speed limit is
reached, pressing the accelerator pedal
no longer has any effect.
The speed limiter is switched on man-
ually: it requires a programmed speed
of at least 20 mph (30 km/h).
The speed limiter is switched off by
manual operation of the control.
The programmed speed can be
exceeded temporarily by pressing the
a c c e l e r a t o r fi r m l y .
To return to the programmed speed,
simply slow down to a speed below the
programmed speed.
The programmed speed remains in the
memory when the ignition is switched
off.
The speed limiter cannot, in any circum-
stances, replace the need to respect
speed limits, nor can it replace the need
for vigilance and responsibility on the
part of the driver. The controls of this system are grouped
together on stalk
A .
1. Speed limiter mode selection dial
2. Value decrease button
3. Value increase button
4. Speed limiter on/off button The programmed information is grouped
together on the instrument panel screen.
5. Speed limiter on/off indication
6. Speed limiter mode selection indica-
tion
7. Programmed speed value
Steering mounted controls Displays on the instrumen
t panel
Page 68 of 107
!
72
Programming
Turn dial 1 to the "LIMIT" position:
the speed limiter mode is selected
but is not switched on (OFF).
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed
speed will not have any effect unless you press the pedal
fi r m l y past the point of resistance .
The speed limiter is deactivated temporarily and the pro-
g r a m m e d s p e e d , w h i c h i s s t i l l d i s p l a y e d , fl a s h e s .
Returning to the programmed speed, by means of intentional
or unintentional deceleration of the vehicle, automaticall y
c a n c e l s t h e fl a s h i n g o f t h e p r o g r a m m e d s p e e d . Return to normal driving
Turn dial 1 to the "0" position: the
speed limiter mode is deselected.
The display returns to the distance
recorder.
You do not have to switch the speed
limiter on in order to set the speed.
Switch the speed limiter off by pressing button 4 : the
d i s p l a y c o n fi r m s t h a t i t h a s b e e n s w i t c h e d o f f ( O F F ) .
Switch the speed limiter back on by pressing button 4
again.
Set the speed value by pressing button 2 or 3 (e.g.: 55 mph
(90 km/h)).
You can then change the programmed speed using but tons 2
and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
Switch the speed limiter on by pressing button 4 . Operating fault
In the event of a speed limiter malfunc-
tion, the speed is cleared resulting in
fl a s h i n g o f t h e d a s h e s .
Have the system checked by a PEUGEOT
dealer.
On a steep descent or in the event
of sharp acceleration, the speed
limiter will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is posi-tioned correctly,
- d o n o t fi t o n e m a t o n t o p o f a n o - ther.
Page 69 of 107
74
BONNET
Component which protects and provides
access to the components of the engine
for checking of the various levels.
- At the front, lift the safety catch and raise the bonnet. - Secure the stay to hold the bonnet
open.
Closing
- Put the stay back in its housing.
- Lower the bonnet and release it at the end of its travel.
- Check that the bonnet is locked.
RUNNING OUT OF FUEL
(DIESEL)
If you should run out of fuel, it is neces-
sary to prime the fuel system:
- fi l l t h e f u e l t a n k w i t h a t l e a s t fi v e l i t r e s of diesel,
- squeeze and release the manual priming pump, located under the
bonnet under the protective cover,
until fuel appears in the transparent
pipe,
- operate the starter until the engine starts.
Opening
- Pull the release lever located on the
left, below the dashboard.
When the engine is hot, handle the
safety catch and the bonnet stay with
care (risk of burns).
Page 70 of 107
75
1.4 LITRE TURBO DIESEL HDI
(70 HP) ENGINE
1. Coolant reservoir.
2. Engine oil dipstick.
3. Power steering reservoir.
4. Windscreen wash reservoir.
5. Priming pump.
6. E n g i n e o i l fi l l e r c a p .
7. A i r fi l t e r .
8. B r a k e fl u i d r e s e r v o i r .
9. Battery.
10. Fusebox.
11. P a s s e n g e r c o m p a r t m e n t fi l t e r .
1.1 LITRE (60 HP) AND 1.4 LITRE
(75 HP) PETROL ENGINES
1. Power steering reservoir.
2. Windscreen wash reservoir.
3. Coolant reservoir.
4. B r a k e fl u i d r e s e r v o i r .
5. Battery (without protective cover for
the 1.1 litre engine).
6. A i r fi l t e r .
7. Engine oil dipstick.
8. E n g i n e o i l fi l l e r c a p .
9. P a s s e n g e r c o m p a r t m e n t fi l t e r .
Page 71 of 107
!
76
CHECKING THE LEVELS Brake fluid level Used oil
Oil level
Check the level regularly
and top up between chang-
es. The maximum consump-
tion is 0.5 litre per 600 miles
(1 000 km).
Check the level with the vehicle level,
engine cold, using the dipstick. T h i s fl u i d m u s t a l w a y s b e a t t h e
maximum level.
T h e b r a k e fl u i d m u s t b e c h a n g e d
according to the manufacturer's
servicing schedule.
U s e fl u i d s r e c o m m e n d e d b y t h e m a n u -
f a c t u r e r , w h i c h f u l fi l D O T 4 s t a n d a r d s .
Note : b r a k e fl u i d i s h a r m f u l t o h e a l t h
and very corrosive. Avoid all contact
with the skin.
Cooling system
Dipstick
There are two marks on the
dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
Power steering reservoir
Open the reservoir, with the engine at
ambient temperature. The level should
always be above the MIN. mark and
close to the MAX. mark.
Oil change
According to the information given in
the Warranty and Maintenance Record.
Viscosity selection
In all cases, the oil used must meet the
manufacturer's requirements. Windscreen wash level Avoid used oil coming into pro-
longed contact with the skin.
Empty the used oil into the con-
tainers intended for this purpose
in the PEUGEOT network.
Do not dispose of used oil, brake
fl u i d o r c o o l a n t i n t o d r a i n s o r o n t o
the ground.
T h i s fl u i d m u s t a l w a y s b e a t t h e
maximum level (circular line).
U s e t h e fl u i d r e c o m m e n d e d b y
the manufacturer.
When the engine is warm, the tempera-
ture of the coolant is controlled by the
engine fan. As this fan can operate with
the ignition key removed and because
the cooling system is pressurised, wait
for at least one hour after the engine has
stopped before carrying out any work.
Slacken the cap by two turns to release
the pressure to prevent any risk of scald-
ing. When the pressure has dropped,
remove the cap and top up the level.
Note: the coolant does not need to be
changed. For best quality cleaning and to
a v o i d f r e e z i n g , t h i s fl u i d m u s t
not be topped up or replaced
with water.
To maintain the reliability of engines
and emission control systems, the use
of additives in engine oil is prohibited.
Page 72 of 107
!
77
CHECKS
Check these components, or have them
checked by a PEUGEOT dealer, in ac-
cordance with the servicing booklet and
in relation to your engine.
Battery
Air filter and passenger compartment filter
Brake pads
Parking brake
Brake disc/drum wear Oil filter
Manual gearbox
Only use products recommended
by PEUGEOT or products of equi-
v a l e n t q u a l i t y a n d s p e c i fi c a t i o n s .
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
H a v e t h e fi l t e r e l e m e n t s r e -
placed regularly.
If you drive
in dusty conditions, change
them twice as often. Brake pad wear depends on
the style of driving, in particular
for vehicles which are used in
town, over short distances.
It may be necessary to check the thickness
of the pads, even between services.
Where the parking brake trav-
el is too great or there is a re-
duction in the performance of
the system, the parking brake
should be adjusted, even be-
tween services.
Have the system checked by a PEUGEOT
dealer.
For any information relating to
checking the wear of the brake
discs and/or drums, contact a
PEUGEOT dealer. C h a n g e t h e fi l t e r r e g u l a r l y , i n
accordance with the servicing
schedule.
This does not require an oil
change. Check the level in ac-
cordance with the manufacturer's
servicing schedule.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
