2010 MITSUBISHI GRANDIS turn signal bulb

Indication lamps
E00501600012Turn-signal indication lamps/
Hazard warning indication
lamps
E00501700329
These
indication lamps blink on and off
when a turn-signal lamp is operating.
NOTE
l If the blinking is too fast, the
cause may be a blown lamp bulb
or a faulty turn-signal connection.
When the hazard warning lamp switch is
pressed, all turn-signal lamps will flash
on and off continuously. High-beam indication lamp
E00501800160
This

indication lamp illuminates when
the high-beam is used. Front fog lamp indication lamp
E00501900321
This

lamp illuminates while the front
fog lamps are on. Rear fog lamp indication lamp
E00502000101
This

lamp illuminates while the rear fog
lamp is on. Position lamp indication lamp
E00508900102
This

lamp illuminates with the lamp
switch at “ ” or “ ” position
Diesel preheat indication lamp
(diesel-powered vehicles)
E00502300061
This

indication lamp illuminates when
the ignition switch is placed in the “ON”
position. As the glow plug becomes hot,
the lamp goes out and the engine can be
started. If it does not go off after a few
seconds, we recommend you to have the
vehicle checked.
NOTE
l If the engine is cold, the diesel pre-
heat indication lamp is on for a lon-
ger time.
l When the engine has not been star-
ted within about 5 seconds after
the diesel preheat indication lamp
went out, return the ignition
switch to the “LOCK” position.
Then, turn the switch to the “ON”
position to preheat the engine
again.
l When the engine is warm, the die-
sel preheat indication lamp does
not come on even if the ignition
switch is placed in the “ON” posi-
tion. Warning lamps
E00502400017 Brake warning lamp
E00502501930
This

lamp illuminates when the ignition
switch is turned to the “ON” position,
and the lamp goes off after a few seconds.
Always make sure that the lamp goes off
before driving.
With the ignition switch in the “ON” po-
sition, the brake warning lamp illumi-
nates under the following conditions:
l When the parking brake lever has
been engaged.
l When the brake fluid level in the
reservoir falls to a low level.
l When the brake force distribution
function is not operating correctly. CAUTION
l
In
the situations listed below,
brake performance may be com-
promised or the vehicle may be-
come unstable if brakes are ap-
plied suddenly; consequently,
avoid driving at high speeds or
applying the brakes suddenly.
Furthermore, the vehicle
should be brought to a stop in a
safe location and to have it
checked. Instruments and controls
3-06
3
Presented by http://mmc-manuals.ru/ \251

Turn/Lane-change signals
E00506501156
The
turn-signal lamps flash when the switch is op-
erated (with the ignition switch in the “ON” posi-
tion). At the same time, the turn signal indicator
flashes. 1- Turn-signals
When
making a normal turn, use position
(1). The lever will return automatically when
cornering is completed.
There are times when the lever will not re-
turn after cornering. This occurs when the
steering wheel is turned only slightly.
In such cases, return the lever by hand.
2- Lane-change signals When changing lanes, use position (2). It
will return to the neutral position when re-
leased.
NOTE l If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned
out. We recommend you to have the vehicle
inspected. l
It
is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details. • Sounding of a buzzer as the turn-signallamps flash.
• Flashing of the turn-signal lamps and the indication lamp in the meter when the lev-
er is operated with the ignition switch in
the “ACC” position. Hazard warning flasher switch
E00506600567
Use
the hazard warning flasher switch when the ve-
hicle has to be parked on the road for any emergency.
The hazard warning flashers can always be operat-
ed, regardless of the position of the ignition key.

Push the switch to turn on the hazard warning flash-
ers; push the switch again to turn them off.
When this switch is operated, all turn-signal lamps
flash continuously, as do the turn-signal indication
lamps in the instrument cluster. NOTE
l If

the lamps are kept flashing for a long time,
the battery will be discharged, resulting in
hard engine starting or no start condition. Instruments and controls
3-21 3
Presented by http://mmc-manuals.ru/ \251

4. Insert a new fuse of the same capacity by us-
ing the fuse puller and insert the fuse at the
same place in the fuse block. CAUTION
l
If
the newly inserted fuse blows again af-
ter a short time, we recommend you to
have the electrical system checked to find
the cause and rectify it.
l Never use a fuse with a capacity larger
than that specified or any substitute, such
as wire, foil, etc.; doing so will cause the
circuit wiring to heat up and could cause
a fire. Replacement of lamp bulbs
E01003100622
Before

replacing a bulb, ensure the lamp is off. Do
not touch the glass part of the new bulb with your
bare fingers; the skin oil left on the glass will evap-
orate when the bulb gets hot and the vapour will
condense on the reflector and dim the surface. CAUTION
l
Bulbs
are extremely hot immediately af-
ter being turned off.
When replacing a bulb, wait for it to cool
sufficiently before touching it. You could
otherwise be burnt.
NOTE l If

you are unsure of how to carry out the
work as required, we recommend you to con-
sult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp and lens.
l When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon
as when window glass mists up on a humid
day, and does not indicate a functional prob-
lem.
When the lamp is switched on, the heat will
remove the fog. However, if water gathers in-
side the lamp, we recommend you to have it
checked.
Bulb capacity E01003200043
When replacing a bulb, use a new bulb with the
same wattage and colour. Outside
E01003302051 1- Front turn-signal lamps: 21 W (W21W)
2-

Headlamps, high-beam: 65 W (H9)
3- Front fog lamps: 51 W (HB4)
4- Headlamps, low beam without discharge lamp: 55 W (H1)
Headlamps, low beam with discharge lamp:
35 W (D2R)
5- Position lamps: 5 W (W5W)
6- Side turn-signal lamps

Codes in parentheses indicate bulb types. Maintenance
8-25 8
Presented by http://mmc-manuals.ru/ \251

1- High-mounted stop lamp
2-
Stop and tail lamps
3- Rear fog lamp (LHD vehicles): 21 W (W21W) Reversing lamp (RHD vehicles): 21 W
(W21W)
4- Licence plate lamps: 5 W (W5W)
5- Reversing lamp (LHD vehicles): 21 W (W21W)
Rear fog lamp (RHD vehicles): 21 W (W21W)
6- Rear turn-signal lamps: 21 W (WY21W)

Codes in parentheses indicate bulb types.
NOTE l The side turn-signal lamps, stop and tail
lamps and high-mounted stop lamp use
LEDs rather than bulbs. For repair and re-
placement, we recommend you to consult a
specialist. Inside
E01003400986 1- Rear personal lamps: 8 W
2-

Room lamp & map lamps: 8 W
3- Vanity mirror lamps*: 3 W
4- Glove box lamp: 1.4 W
5- Door lamps: 3.4 W
6- Luggage compartment lamp: 5 W Headlamps
E01003501290
Replacement of low beam (except for vehicles
with discharge headlamps) 1. Pull

out the connector (B) while pressing the
tab (A). Turn the cap (C) anticlockwise and
remove it. 2. Pull the socket (D) off the bulb.Maintenance
8-26
8
Presented by http://mmc-manuals.ru/ \251

3. Turn the bulb socket (F) anticlockwise to re-
move it. 4. Depress
the tab (G) on the harness connector
and pull the harness connector to remove the
bulb. 5. To
install the bulb, perform the removal
steps in reverse. CAUTION
l
Handle
halogen lamp bulbs with care.
The gas inside halogen lamp bulbs is high-
ly pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the
bulb to break the next time the head-
lamps are operated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc.,
and refit it after drying it thoroughly. Position lamps
E01003700279
Have the position lamp bulbs replaced by a
MITSUBISHI

MOTORS Authorized Service Point. Front turn-signal lamps
E01003800690
1. Turn

the bulb socket anticlockwise to re-
move it. And remove the bulb from the sock-
et by pulling out. 2. To
install the bulb, perform the removal
steps in reverse.
Front fog lamps E01004001289
1. Remove
the 4 clips (A), then pull off the cov-
er (B). Maintenance
8-28
8
Presented by http://mmc-manuals.ru/ \251

2. Depress the tab (C) on the harness connector
and pull the harness connector (D) to remove
it. 3. Remove
the entire socket and bulb assembly
(E) by turning it anticlockwise. 4. To
install the bulb, perform the removal
steps in reverse. CAUTION
l
Handle
halogen lamp bulbs with care.
The gas inside halogen lamp bulbs is high-
ly pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the
bulb to break the next time the fog lamps
are operated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc.,
and refit it after drying it thoroughly. Rear combination lamps
E01004201063
1. Insert
a straight blade (or minus) screwdriver
with a cloth over its tip into the notch at the bottom of the lid of the lamp whose bulb you
wish to replace. Use it to lever off the lid.
2. Turn
the socket anticlockwise and remove it.
Withdraw the bulb from the socket. A- Rear turn-signal lamp
B-
Rear fog lamp (driver’s side)Reversing lamp (passenger’s side)
3. To install the bulb, perform the removal steps in reverse. Maintenance
8-29 8
Presented by http://mmc-manuals.ru/ \251

Coolant 8-06,9-15
Number 9-02
Oil 8-04
Oil and oil filter
9-14
Overheating 6-04
Specifications 9-08
Used engine oils safety instructions and disposal
information 06
Water temperature gauge 3-04
Error codes 5-28
Exterior and interior lamp operation 8-18
FFluid capacities and lubricants 9-14
Fluid
Automatic transmission fluid

8-08,9-15
Brake fluid 8-09,9-14
Clutch fluid 8-09,9-14
Engine coolant 8-06,9-15
Power steering fluid 8-09,9-14
Washer fluid 8-08,9-14
For cold and snowy weather 8-19
Front automatic air conditioning 5-05
Front fog lamps Bulb capacity 8-25
Indication lamp 3-06
Replacement 8-28
Front fog lamp Switch 3-22
Front seat 2-05
Front turn-signal lamps Bulb capacity 8-25
Replacement 8-28
Fuel consumption 9-13
Fuel Filling the fuel tank 03
Fuel gauge 3-03
Fuel selection 02 Low fuel warning lamp 3-04
Modification/alterations to the electrical or fuel
systems 05
Tank capacity

03
Fuse load capacity 8-20
Fuse replacement 8-24
Fuses 8-20
Fusible links 8-19
G Gauges 3-05
General maintenance

8-18
General vehicle data 9-04
Genuine parts 05
Glove box 5-38
Glove box lamp Bulb capacity 8-26
Replacement 8-32
H Handling of compact discs 5-30
Hazard warning indication lamps

3-06
Head restraints 2-11
Headlamp levelling 3-19
Headlamp levelling switch 3-19
Headlamps Bulb capacity 8-25
Headlamp flasher 3-19
Replacement 8-26
Switch 3-18
Heated mirror 4-08
Heated seats 2-06
High-beam indication lamp 3-06
Hinges and latches lubrication 8-19
Horn switch 3-26 I If the vehicle breaks down 6-02
Ignition switch 4-08
Indication and warning lamps

3-05
Indication lamps 3-06
Inside rear-view mirror 4-06
Inside tailgate release 1-10
Installation of accessories 04
Instrument panel upper box 5-39
Instruments 3-02
Interior lamp switch 5-36
Interior lamps 5-35
J Jacking up the vehicle 6-07
Jack 6-06
Storage 6-06
Jump starting (Emergency starting)

6-02
K Keyless entry system 1-04
Keys 1-02
L Labeling 9-02
Lamp monitor buzzer

3-19
Lamps (headlamps, fog lamp, etc.) auto-cutout func-
tion 3-18
Lamps (room lamps, etc.) auto-cutout function (Ve-
hicles with keyless entry system) 5-37
Leakage (Fuel, engine coolant, oil and exhaust
gas) 8-18
Licence plate lamps Bulb capacity 8-26 Alphabetical index
2
Presented by http://mmc-manuals.ru/ \251

Replacement 8-30
Low fuel warning lamp 3-04
Lubricants 9-14
Luggage compartment lamp
5-37
Bulb capacity 8-26
Replacement 8-31
Luggage floor box 5-39
Luggage hooks 5-45
LW/MW/FM electronic tuning radio with CD play-
er 5-13
MMaking a flat seat 2-14
Making a luggage area

2-13
Manual transmission 4-13 Oil 9-14
Mirror Inside rear-view mirror 4-06
Outside rear-view mirrors 4-07
MIVEC 4-11
Modification/alterations to the electrical or fuel sys-
tems 05
Multi centre display 3-09
OOdometer 3-03
Oil pressure warning lamp 3-08
Oil
Engine oil 8-04
Manual transmission oil 9-15
Operation under adverse driving conditions

6-18
Outside rear-view mirrors 4-07
Overheating 6-04
PParking 4-05 Parking brake 4-04
Parking brake stroke 8-16
Personal box 5-39
Personal table 5-42
Position lamps Bulb capacity

8-25
Indication lamp 3-06
Replacement 8-28
Possible driving speed 4-14
Power steering Fluid 8-09,9-14
System 4-23
Precautions to observe when using wipers and wash-
ers 3-25
Pregnant women restraint 2-20
Puncture Tyre changing 6-11
R Radio
LW/MW/FM electronic tuning radio with CD
player 5-13
Rear automatic air conditioning

5-09
Rear combination lamps Bulb capacity 8-26
Replacement 8-29
Rear cooler 5-09
Rear fog lamp Bulb capacity 8-26
Indication lamp 3-06
Replacement 8-29
Switch 3-22
Rear heater 5-09
Rear personal lamps 5-37 Bulb capacity 8-26
Replacement 8-31
Rear side box 5-39
Rear turn-signal lamps Bulb capacity 8-26
Replacement

8-29
Rear window demister switch 3-25
Rear-view mirror Inside 4-06
Outside 4-07
Replacement of lamp bulbs 8-25
Reversing lamps Bulb capacity 8-26
Replacement 8-29
Roof carrier precaution 4-33
Room lamp & map lamps 5-36 Bulb capacity 8-26
Replacement 8-30
Running-in recommendations 4-03
S Safe driving techniques 4-03
Seat arrangement

2-03
Seat belt 2-17 Adjustable seat belt anchor (front seats) 2-19
Child restraint 2-21
Force limiter system 2-21
Inspection 2-29
Pregnant women restraint 2-20
Pretensioner system 2-20
Rear seat belt storage 2-19
Seat belt reminder/warning lamp 2-19
Seat Adjustment 2-05
Armrest 2-06,2-08
Front seat 2-05
Head restraints 2-11
Heated seats 2-06
Making a flat seat 2-14
Second seat 2-07
Third seat 2-10
Seats Alphabetical index
3
Presented by http://mmc-manuals.ru/ \251