l
If no station is found with your desired PTY,
the display will show “EMPTY” for about 5
seconds and the radio will return to the previ-
ous station.
How to enter PTYs in the memory E00721400122
As many as 6 PTYs can be entered in the memory.
Follow the steps described below.
1. Press
either the TUNE/SEEK button (5 or 6)
to tune the PTY to be entered in the memory.
2. Press one of the memory select buttons (3) for 2 seconds or longer. The sound will be
momentarily interrupted while the PTY is be-
ing entered into the memory. The number of
the button corresponding to the entry into the
memory and the PTY are displayed.
3. The preset memory setting is retrieved by pressing the button and then releasing it with-
in about 2 seconds.
To change the language of PTY display E00721500181
You can select your favourite language among Eng-
lish,
French, German, Swedish, Spanish and Italian.
1. Press the “MENU” button (A) to select the language of PTY display mode.
Refer to “Function setup mode” on page
5-21.
2. Press the audio adjust button (B) to select a language.
NOTE l After selecting a mode, you can leave the func-
tion setup mode by taking either of the fol-
lowing steps: • Press
the “MENU” button for at least 2
seconds.
• Make no entry for 7 seconds. Traffic information
E00721600179
The radio will automatically tune in to traffic infor-
mation
broadcasts while receiving FM broadcasts
or playing compact discs.
To select this function, follow the instructions below. 1. Press
the TP button (7). The display will
show “TP” (12). If the RDS data can be read,
the display will show “RDS” (10). If not, the
display will show “NO RDS” for about 5 sec-
onds.
2. If the radio detects traffic information on ei- ther the station currently selected or another
station, the display will show “TRAF INF”
for 5 seconds followed by a 2-second indica-
tion of the frequency. Then, it will show the
name of the station broadcasting the traffic in-
formation to which you will listen. The vol-
ume level is set separately for listening to nor-
mal audio programs and for listening to traf-
fic information. The volume level will there-
fore change automatically to that set when
traffic information was last received. When
the traffic information broadcast is over, the
radio will return to the previously received
program and to the corresponding volume lev-
el.
3. Press the TP button (7) to return to the previ- ous condition.
NOTE l While “TP” is illuminated, the radio stops on-
ly at TP stations even if the TUNE/SEEK but-
ton (5 or 6) is pressed. For pleasant driving
5-20
5
Presented by http://mmc-manuals.ru/ \251
TP (Traffic information Program) search function
E00721800012
The traffic information program standby function
is
turned on (with the TP indicator (12) shown on
the display) and after about 45 seconds since the
RDS indicator (10) turns off due to weak signal or
the tuning station is changed over from a TP sta-
tion to a station which does not broadcast traffic in-
formation, the sound will beep 5 times and seeks
out a TP station in all frequencies automatically. The TP search function can be turned ON and OFF.
Refer to “Function setup mode” on page
5-21.
Emergency broadcasts E00721700011 If an emergency broadcast is caught while receiv-
ing
a FM broadcast or playing back a compact disc
with the ignition switch in “ACC” or “ON” posi-
tion, the display will show “ALARM” and the emer-
gency broadcast will interrupt the current program.
The volume level is set separately for listening to
normal audio programs and for listening to emer-
gency broadcasts. The volume level will therefore
change automatically to that set when an emergen-
cy broadcast or traffic information broadcast was
last received. When the emergency broadcast is
over, the radio will return to the previously re-
ceived program and to the corresponding volume
level.
Function setup mode E00722500175
It is possible to change the following functions: l
AF
l CT
l REG
l TP-S
l Language of PTY display
1. Press
the “MENU” button to select the func-
tion setup mode. For pleasant driving
5-21 5
Presented by http://mmc-manuals.ru/ \251
2. Press the “MENU” button repeatedly to se-
lect the mode you wish to change. The order
is: AF CT REG TP-S PH
MUTE Language of PTY display Func-
tion setup mode OFF.
NOTE l Although
“PH” and “MUTE” appear on the
display, the PH and MUTE functions are in-
operative.
3. Select the desired setting for each mode to be turned ON and OFF as shown below. The setting will be shown on the display.Example NOTE
l After
selecting a mode, you can leave the func-
tion setup mode by taking either of the fol-
lowing steps: • Press the “MENU” button for at least 2seconds.
• Make no entry for 7 seconds.
l For instructions on setting the language of
PTY display, refer to “To change the lan-
guage of PTY display” on page 5-20. For pleasant driving
5-22
5
Presented by http://mmc-manuals.ru/ \251
