2010 MITSUBISHI GRANDIS bulb

Indication lamps
E00501600012Turn-signal indication lamps/
Hazard warning indication
lamps
E00501700329
These
indication lamps blink on and off
when a turn-signal lamp is operating.
NOTE
l If the blinking is too fast, the
cause may be a blown lamp bulb
or a faulty turn-signal connection.
When the hazard warning lamp switch is
pressed, all turn-signal lamps will flash
on and off continuously. High-beam indication lamp
E00501800160
This

indication lamp illuminates when
the high-beam is used. Front fog lamp indication lamp
E00501900321
This

lamp illuminates while the front
fog lamps are on. Rear fog lamp indication lamp
E00502000101
This

lamp illuminates while the rear fog
lamp is on. Position lamp indication lamp
E00508900102
This

lamp illuminates with the lamp
switch at “ ” or “ ” position
Diesel preheat indication lamp
(diesel-powered vehicles)
E00502300061
This

indication lamp illuminates when
the ignition switch is placed in the “ON”
position. As the glow plug becomes hot,
the lamp goes out and the engine can be
started. If it does not go off after a few
seconds, we recommend you to have the
vehicle checked.
NOTE
l If the engine is cold, the diesel pre-
heat indication lamp is on for a lon-
ger time.
l When the engine has not been star-
ted within about 5 seconds after
the diesel preheat indication lamp
went out, return the ignition
switch to the “LOCK” position.
Then, turn the switch to the “ON”
position to preheat the engine
again.
l When the engine is warm, the die-
sel preheat indication lamp does
not come on even if the ignition
switch is placed in the “ON” posi-
tion. Warning lamps
E00502400017 Brake warning lamp
E00502501930
This

lamp illuminates when the ignition
switch is turned to the “ON” position,
and the lamp goes off after a few seconds.
Always make sure that the lamp goes off
before driving.
With the ignition switch in the “ON” po-
sition, the brake warning lamp illumi-
nates under the following conditions:
l When the parking brake lever has
been engaged.
l When the brake fluid level in the
reservoir falls to a low level.
l When the brake force distribution
function is not operating correctly. CAUTION
l
In
the situations listed below,
brake performance may be com-
promised or the vehicle may be-
come unstable if brakes are ap-
plied suddenly; consequently,
avoid driving at high speeds or
applying the brakes suddenly.
Furthermore, the vehicle
should be brought to a stop in a
safe location and to have it
checked. Instruments and controls
3-06
3
Presented by http://mmc-manuals.ru/ \251

Turn/Lane-change signals
E00506501156
The
turn-signal lamps flash when the switch is op-
erated (with the ignition switch in the “ON” posi-
tion). At the same time, the turn signal indicator
flashes. 1- Turn-signals
When
making a normal turn, use position
(1). The lever will return automatically when
cornering is completed.
There are times when the lever will not re-
turn after cornering. This occurs when the
steering wheel is turned only slightly.
In such cases, return the lever by hand.
2- Lane-change signals When changing lanes, use position (2). It
will return to the neutral position when re-
leased.
NOTE l If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned
out. We recommend you to have the vehicle
inspected. l
It
is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details. • Sounding of a buzzer as the turn-signallamps flash.
• Flashing of the turn-signal lamps and the indication lamp in the meter when the lev-
er is operated with the ignition switch in
the “ACC” position. Hazard warning flasher switch
E00506600567
Use
the hazard warning flasher switch when the ve-
hicle has to be parked on the road for any emergency.
The hazard warning flashers can always be operat-
ed, regardless of the position of the ignition key.

Push the switch to turn on the hazard warning flash-
ers; push the switch again to turn them off.
When this switch is operated, all turn-signal lamps
flash continuously, as do the turn-signal indication
lamps in the instrument cluster. NOTE
l If

the lamps are kept flashing for a long time,
the battery will be discharged, resulting in
hard engine starting or no start condition. Instruments and controls
3-21 3
Presented by http://mmc-manuals.ru/ \251

Service precautions
....................................................................... 8-02
Catalytic converter ........................................................................ 8-02
Bonnet...........................................................................................8-03
Engine oil ......................................................................................8-04
Engine coolant .............................................................................. 8-06
Automatic transmission fluid*
......................................................8-08
Washer fluid ................................................................................. 8-08
Brake fluid/Clutch fluid* .............................................................. 8-09
Power steering fluid ...................................................................... 8-09
Battery .......................................................................................... 8-10
Tyres............................................................................................. 8-11
Clutch pedal free play* ................................................................. 8-15
Brake pedal free play .................................................................... 8-16
Parking brake lever stroke ............................................................ 8-16
Parking brake break-in..................................................................8-16
Wiper blades ................................................................................. 8-17
General maintenance .................................................................... 8-18
For cold and snowy weather......................................................... 8-19
Fusible links.................................................................................. 8-19
Fuses............................................................................................. 8-20
Replacement of lamp bulbs .......................................................... 8-25Maintenance
8
Presented by http://mmc-manuals.ru/ \251

3. Slide a new wiper blade through the hook
(B) on the wiper arm. NOTE
l Do

not allow the wiper arm to fall onto the
window glass; it could damage the glass.
4. Firmly insert the retainer (C) into the groove (D) in the wiper blade. Refer to the illustration to ensure that the re-
tainers

are correctly aligned as you insert
them into the groove. NOTE
l If

a retainer is not supplied with the new wip-
er blade, use the retainer from the old blade. General maintenance
E01002700256
Fuel, engine coolant, oil and exhaust
gas leakage
Look

under the body of your vehicle to check for
fuel, engine coolant, oil and exhaust gas leaks. WARNING
l If
you see a suspicious fuel leak or if you
smell fuel, do not operate the vehicle; we
recommend you to call for assistance.
Exterior and interior lamp operation
Operate
the combination lamp switch to check that
all lamps are functioning properly.
If the lamps do not illuminate, the probable cause
is a blown fuse or defective lamp bulb. Check the
fuses first. If there is no blown fuses, check the
lamp bulbs.
For information regarding the inspection and re-
placement of the fuses and the lamp bulbs, refer to
“Fuses” on page 8-20 and “Replacement of lamp
bulbs” on page 8-25.
If the fuses and bulbs are all OK, we recommend
you to have your vehicle checked and repaired.
Meter, gauge and indicator/warning
lamps operation
Run the engine to check the operation of all meters,
gauges, and indicator/warning lamps.
If there is anything wrong, we recommend you to
have your vehicle inspected. Maintenance
8-18
8
Presented by http://mmc-manuals.ru/ \251

4. Insert a new fuse of the same capacity by us-
ing the fuse puller and insert the fuse at the
same place in the fuse block. CAUTION
l
If
the newly inserted fuse blows again af-
ter a short time, we recommend you to
have the electrical system checked to find
the cause and rectify it.
l Never use a fuse with a capacity larger
than that specified or any substitute, such
as wire, foil, etc.; doing so will cause the
circuit wiring to heat up and could cause
a fire. Replacement of lamp bulbs
E01003100622
Before

replacing a bulb, ensure the lamp is off. Do
not touch the glass part of the new bulb with your
bare fingers; the skin oil left on the glass will evap-
orate when the bulb gets hot and the vapour will
condense on the reflector and dim the surface. CAUTION
l
Bulbs
are extremely hot immediately af-
ter being turned off.
When replacing a bulb, wait for it to cool
sufficiently before touching it. You could
otherwise be burnt.
NOTE l If

you are unsure of how to carry out the
work as required, we recommend you to con-
sult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp and lens.
l When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon
as when window glass mists up on a humid
day, and does not indicate a functional prob-
lem.
When the lamp is switched on, the heat will
remove the fog. However, if water gathers in-
side the lamp, we recommend you to have it
checked.
Bulb capacity E01003200043
When replacing a bulb, use a new bulb with the
same wattage and colour. Outside
E01003302051 1- Front turn-signal lamps: 21 W (W21W)
2-

Headlamps, high-beam: 65 W (H9)
3- Front fog lamps: 51 W (HB4)
4- Headlamps, low beam without discharge lamp: 55 W (H1)
Headlamps, low beam with discharge lamp:
35 W (D2R)
5- Position lamps: 5 W (W5W)
6- Side turn-signal lamps

Codes in parentheses indicate bulb types. Maintenance
8-25 8
Presented by http://mmc-manuals.ru/ \251

1- High-mounted stop lamp
2-
Stop and tail lamps
3- Rear fog lamp (LHD vehicles): 21 W (W21W) Reversing lamp (RHD vehicles): 21 W
(W21W)
4- Licence plate lamps: 5 W (W5W)
5- Reversing lamp (LHD vehicles): 21 W (W21W)
Rear fog lamp (RHD vehicles): 21 W (W21W)
6- Rear turn-signal lamps: 21 W (WY21W)

Codes in parentheses indicate bulb types.
NOTE l The side turn-signal lamps, stop and tail
lamps and high-mounted stop lamp use
LEDs rather than bulbs. For repair and re-
placement, we recommend you to consult a
specialist. Inside
E01003400986 1- Rear personal lamps: 8 W
2-

Room lamp & map lamps: 8 W
3- Vanity mirror lamps*: 3 W
4- Glove box lamp: 1.4 W
5- Door lamps: 3.4 W
6- Luggage compartment lamp: 5 W Headlamps
E01003501290
Replacement of low beam (except for vehicles
with discharge headlamps) 1. Pull

out the connector (B) while pressing the
tab (A). Turn the cap (C) anticlockwise and
remove it. 2. Pull the socket (D) off the bulb.Maintenance
8-26
8
Presented by http://mmc-manuals.ru/ \251

3. Unhook the spring (E), which secures the
bulb, and remove the bulb. 4. To
install the bulb, perform the removal
steps in reverse. CAUTION
l
Handle
halogen lamp bulbs with care.
The gas inside halogen lamp bulbs is high-
ly pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the
bulb to break the next time the head-
lamps are operated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc.,
and refit it after drying it thoroughly. Replacement of low beam (for vehicles with dis-
charge headlamps)
Do

not attempt to disassemble or repair discharged
headlamps, and do not attempt to replace their bulbs. CAUTION
l
A high voltage is present in the power cir-
cuit

and in the bulbs and bulb terminals.
To avoid the risk of an electric shock, con-
tact a MITSUBISHI MOTORS Author-
ized Service Point whenever repair or re-
placement is necessary. Replacement of high-beam
1. For
diesel-powered vehicles, remove the
bolts (A) to remove the power steering reser-
voir tank (B). 2. Pull
out the connector (D) while pressing the
tab (C). Turn the cap (E) anticlockwise and
remove it. Maintenance
8-27 8
Presented by http://mmc-manuals.ru/ \251

3. Turn the bulb socket (F) anticlockwise to re-
move it. 4. Depress
the tab (G) on the harness connector
and pull the harness connector to remove the
bulb. 5. To
install the bulb, perform the removal
steps in reverse. CAUTION
l
Handle
halogen lamp bulbs with care.
The gas inside halogen lamp bulbs is high-
ly pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the
bulb to break the next time the head-
lamps are operated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc.,
and refit it after drying it thoroughly. Position lamps
E01003700279
Have the position lamp bulbs replaced by a
MITSUBISHI

MOTORS Authorized Service Point. Front turn-signal lamps
E01003800690
1. Turn

the bulb socket anticlockwise to re-
move it. And remove the bulb from the sock-
et by pulling out. 2. To
install the bulb, perform the removal
steps in reverse.
Front fog lamps E01004001289
1. Remove
the 4 clips (A), then pull off the cov-
er (B). Maintenance
8-28
8
Presented by http://mmc-manuals.ru/ \251