2010 MITSUBISHI GRANDIS ECU

Even when such parts are officially authorized, for
example
by a “general operators permit” (an ap-
praisal for the part) or through the execution of the
part in an officially approved manner of construc-
tion, or when a single operation permit following
the attachment or installation of such parts, it can-
not be deduced from that alone, that the driving safe-
ty of your vehicle has not been affected.
Consider also that there basically exists no liability
on the part of the appraiser or the official. Only in
the case of parts (MITSUBISHI MOTORS original
replacement or exchange parts as well as
MITSUBISHI MOTORS genuine accessories) that
are recommended and released by a MITSUBISHI
MOTORS Authorized Service Point and that are at-
tached or installed by a MITSUBISHI MOTORS
Authorized Service Point can you assume, that op-
timal safety has been provided. The same also per-
tains to modifications of MITSUBISHI vehicles
with respect to the production specifications. For
your own safety, in such cases as well, you should
only undertake modifications according to the rec-
ommendations of a MITSUBISHI MOTORS Au-
thorized Service Point. Modification/alterations to the
electrical or fuel systems E00200400238
MITSUBISHI MOTORS
has always manufactured
safe, high quality vehicles. In order to maintain this
safety and quality, it is important that any accesso-
ry that is to be fitted, or any modifications carried
out which involve the electrical or fuel systems,
should be carried out in accordance with
MITSUBISHI MOTORS guidelines. CAUTION
l
If
the wiring interferes with any part of
the vehicle bodywork or improper instal-
lation methods are used, i.e. protective
fuses not installed, etc.), electronic devi-
ces may be adversely affected, possibly re-
sulting in an electrical fire or other fail-
ures that may cause an accident. Genuine parts
E00200500590
MITSUBISHI MOTORS

has gone to great lengths
to bring you a superbly crafted automobile offering
the highest quality and dependability.
Use MITSUBISHI MOTORS genuine parts, de-
signed and manufactured to maintain your
MITSUBISHI MOTORS automobile at top per-
formance. MITSUBISHI MOTORS genuine parts
are identified by this mark and are available at all
MITSUBISHI MOTORS Authorized Service
Points. General information
05
Presented by http://mmc-manuals.ru/ \251

l
If you wish to add a remote control switch,
we recommend you to contact your
MITSUBISHI MOTORS Authorized Service
Point.
A maximum of 4 remote control switches are
available for your vehicle.
Procedure for replacing the remote
control switch battery E00309500086
1. Remove
the screw (A) from the remote con-
trol switch. 2. With
the MITSUBISHI mark facing you, in-
sert the cloth covered tip of a straight blade
(or minus) screwdriver into the notch in the remote control switch case and use it to open
the case.
NOTE
l Be

sure to perform the procedure with the
MITSUBISHI mark facing you. If the
MITSUBISHI mark is not facing you when
you open the remote control switch case, the
switches may come out. 3. Remove
the remote control transmitter from
the remote control switch case. Then, open
the remote control transmitter using the meth-
od described in step 2. 4. Remove the old battery.
5. Install

a new battery with the + side (B) down.
Coin type battery
CR1616
- side
+ side 6. Close the remote control transmitter firmly.
7.

Place the remote control transmitter in the re-mote control switch case, then securely close
the remote control switch case.
8. Attach the screw (A) removed in step 1. Locking and unlocking
1-05 1
Presented by http://mmc-manuals.ru/ \251

To lock or unlock from inside the vehi-
cle
The
tailgate can be locked or unlocked by using the
inside lock knob (driver side), regardless of the po-
sition of the ignition key. 1- Lock
2-

Unlock
If the tailgate is locked or unlocked by using the in-
side lock knob (driver side), it can still be locked or
unlocked with the key.
NOTE l Repeated continuous operating between lock
and unlock could cause the central door
lock’s built-in protection circuit to prevent
the system from operating. If this occurs,
wait about 1 minute before operating the in-
side lock knob. To open
Pull the tailgate handle upward to open the tailgate.
CAUTION
l
Make sure there is no one standing near-
by when opening the tailgate.
NOTE l If

you do not open the tailgate immediately
after pulling the handle, the tailgate will auto-
matically be relocked. If this happens, pull
the handle again and lift the tailgate with the
handle still pulled.
l The tailgate cannot be opened when the bat-
tery is flat or disconnected. To close
Pull

the tailgate grip (A) downward as illustrated
and release it before the tailgate closes completely.
Gently shut the tailgate from the outside so that it
is completely closed. CAUTION
l
To
avoid injuring your hand or arm, do
not attempt to close the tailgate without
letting go off the tailgate grip.
l Before driving, make sure that the tail-
gate is securely closed.
If the tailgate opens while driving the ve-
hicle, objects stored in the luggage area
could fall out onto the road.
NOTE l Gas struts (B) are installed in the locations il-
lustrated

to support the tailgate. Please ob-
serve the following in order to prevent dam-
age or faulty operation. Locking and unlocking
1-09 1
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
The safety mechanism is cancelled just be-
fore the window is fully closed. This al-
lows the window to close completely.
Therefore be especially careful that no fin-
gers are trapped in the window.
NOTE l The

safety mechanism can be activated if the
driving conditions or other circumstances
cause the door windows to be subjected to a
physical shock similar to that caused by a trap-
ped hand or head.
l If the safety mechanism is activated three or
more times in a row, the safety mechanism
will be cancelled and the door window will
not close correctly.
In such a case, the following procedure
should be implemented to rectify this situa-
tion. If the window is open, repeatedly raise
the appropriate window switch until that win-
dow has been fully closed. Following this, re-
lease the switch, raise the switch once again
and hold it in this condition for at least 1 sec-
ond, then release it. You should now be able
to operate all windows in the normal fashion. Sunroof*
E00302700496
There are two sunroofs. A- Front sunroof
B- Rear sunroof
Front sunroof
To tilt up
Push the handle (C) while pressing the button (D). To tilt down
Pull

the handle, returning it to its original position
and securing it in place. Sunshade
Slide the sunshade manually to open and close it.
CAUTION
l
Be
careful that hands are not trapped
when closing the sunshade. Locking and unlocking
1-13 1
Presented by http://mmc-manuals.ru/ \251

NOTE
l Be
sure to tilt down the sunroof before clos-
ing the sunshade.
l The sunshade cannot be closed with the sun-
roof opened. Do not attempt to close the sun-
shade when the sunroof is opened.
Rear sunroof
The rear sunroof can only be operated with the igni-
tion switch in the “ON” position. To open
The sunroof automatically opens if the switch (1) is
pressed.

To stop the moving sunroof, press the
switch (2).
NOTE
l The sunroof automatically stops just before
reaching the fully open position.
Press the switch again to fully open it.
To close
The sunroof automatically closes if the switch (2)
is pressed.
To stop the moving sunroof, press switch (1) Lock switch
When

this switch is operated, the sunroof switch
cannot be used to open or close the sunroof.
To unlock, press it once again. 1- Lock
2-

Unlock
NOTE l If the sunroof switch is operated with the
lock switch pressed, a buzzer sounds to indi-
cate the sunroof cannot be opened or closed.
l With the lock switch pressed, operation of
the power windows with switches other than
the driver’s door switches is also prevented.
Safety mechanism
If a hand or head is trapped in the closing sunroof,
it will reopen automatically.
Nonetheless, make sure that nobody puts their head
or hand out of the sunroof when opening or closing.
The opened sunroof will become operational after
a few seconds.
If the safety mechanism should be activated 5 or
more

times consecutively, normal closing of the sun-
roof will be aborted. In such an event, the follow-
ing steps should be taken: 1. Press the switch (2) repeatedly to fully closethe sunroof and hold the switch (2) for a peri-
od of at least 3 seconds.
2. After pressing the switch (1) to perform full opening, press the switch (2) to fully close
the sunroof.
NOTE l The safety mechanism can be activated if the
driving conditions or other circumstances
cause the sunroof to be subjected to a physi-
cal shock similar to that caused by a trapped
hand or head.
l Avoid stopping the sunroof before it reaches
the opening or closing end during operations.
If this should accidentally happen, repeat the
process from step 1.
3. Following this action, it should be possible to operate the sunroof in the normal manner. WARNING
l Do
not put head, hands or anything else
out of the sunroof opening while driving
the vehicle.
l Never leave a child (or other person who
might not be capable of safe operation of
the sunroof switch) in the vehicle alone.
l Before operating the sunroof, make sure
that nothing is capable of being trapped
(head, hand, finger, etc.). Locking and unlocking
1-14
1
Presented by http://mmc-manuals.ru/ \251

Seat adjustment
E00400300402
Adjust
the driver’s seat so that you are comfortable
and that you can reach the pedals, steering wheel,
switches etc. while retaining a clear field of vision. WARNING
l Do
not attempt to adjust the seat while
driving. This can cause loss of vehicle con-
trol and result in an accident. After ad-
justments are made, ensure the seating is
locked in position by attempting to move
the seat forward and rearward without us-
ing the adjusting mechanism.
l It is extremely dangerous to ride in the
luggage area of a vehicle. Also, the lug-
gage area and rear seats should never be
used as a play area by children. In a colli-
sion, people or children riding unrestrain-
ed in these areas are more likely to be se-
riously injured or killed.
Do not allow people or children to ride in
any area of your vehicle that is not equip-
ped with seats and seat belts, and make
sure that everyone travelling in your vehi-
cle is in a seat and wearing a seat belt, or
in the case of a child is strapped in a child
restraint. WARNING
l To
minimize the risk of personal injury
in the event of a collision or sudden brak-
ing, the seatbacks should always be in the
almost upright position while the vehicle
is in motion. The protection provided by
the seat belts may be reduced significant-
ly when the seatback is reclined. There is
greater risk that the passenger will slide
under the seat belt, resulting in serious in-
jury, when the seatback is reclined. CAUTION
l
Make
sure the seat is adjusted by an
adult or with adult supervision for cor-
rect and safe operation.
l Do not place a cushion or the like be-
tween your back and the seatback while
driving. The effectiveness of the head re-
straints will be reduced in the event of an
accident.
l When sliding the seats, be careful not to
catch your hand or foot.
l When sliding or reclining the seat rear-
ward, pay careful attention to the rear
seat passengers. Front seat
E00400400012
To adjust forward or backward E00400500491
Pull the seat adjusting lever and adjust the seat for-
ward

or backward to the desired position. After ad-
justment, release theadjusting lever to lock the seat
in position. WARNING
l To
ensure the seat is locked securely, try
to move the seat forward or backward
without using the adjusting lever. Seat and seat belts
2-05 2
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
Operate in the high position for quick heat-
ing. Once the seat is warm, set the heater
to low to keep it warm. Slight variations
in seat temperature may be felt while us-
ing the heated seats. This is caused by the
operation of the heater’s internal thermo-
stat and does not indicate a malfunction.
l If the following types of persons use the
heated seats, they might become too hot
or receive minor burns (red skin, heat blis-
ters, etc.):
• Children, elderly or ill people
• People with sensitive skin
• Excessively tired people
• People under the influence of alcoholor sleep inducing medication (cold
medicine, etc.)
l Do not use a blanket, cushion, or other ma-
terial with high heat insulation properties
on the seat while using the heater; this
might cause the heater element to overheat
l Turn the heater off immediately if it ap-
pears to be malfunctioning during use.
NOTE l Do

not place heavy objects on the seat or
stick pins, needles, or other pointed objects
into it.
l When cleaning the seat, do not use benzene,
kerosene, petrol, alcohol, or other organic sol-
vents; these might damage the surface of the
seat and also the heater element.
l If water or any other liquid is spilled on the
seat, allow it to dry thoroughly before attempt-
ing to use the heater. Second seat
E00402000227
When

a person is sitting in the middle seating posi-
tion of the second seat in a cabin with 7-person
seats, adjust the head restraints to heights at which
they lock in position. Refer to “Head restraints” on
page 2-11.
NOTE
l It is possible to adjust each side of the sec-
ond seats forward and backward independent-
ly of the other side, to adjust the seatback an-
gle independently on each side, and to fold
up the seat cushion independently on each
side.
To adjust forward or backward E00402100097
Pull the seat adjusting left- or right-hand lever and
adjust

the seat forward or backward to the desired
position. After adjustment, release the adjusting lev-
er to lock the seat in position.
6-person seat
7-person seat WARNING
l To
ensure the seat is locked securely, try
to move the seat forward or backward
without using the adjusting lever.
To recline the seatback E00402200186
In order to recline the seatback, lean forward slight-
ly,

pull the seatback lock lever up, and then lean
backward to the desired position and release the lev-
er. The seatback will lock in that position.
6-person seat Seat and seat belts
2-07 2
Presented by http://mmc-manuals.ru/ \251

7-person seatWARNING
l When
a person is sitting in the middle seat-
ing position of the second seat in a cabin
with 7-person seats, the two sides of the
second seat must have the same forward/
backward position and the same seatback
angle. Otherwise, the seat belt for the mid-
dle seating position may not be adequate-
ly effective in the event of hard braking
or a collision. CAUTION
l
The
reclining mechanism of the seatback
is spring loaded, causing it to return to
the vertical position when the lock lever
is operated. When using the lever, sit
close to the seatback or hold it with your
hand to control its return motion. Armrest
E00402400250

6 - person seat
To

adjust the armrest angle, tip the armrest forward
and then raise it to the desired position.
To return the armrest to its original position, raise
it backward. 7 - person seat
To use the armrest, fold it down.
To

return to the original position, push it backward
(into the seatback) until it is level with the seat. NOTE
l Do

not stand or sit on the armrest. It could
break.
To get in and out of the third seat E00402500222
The lever can be used to make getting in and out
easier. 1- 1- To get in or out
2-

2- To get out

Fold the seatback forward, then slide the entire seat
forward. To return the seat, slide the entire seat
fully backward to retain it and then raise the seat-
back.
After returning the seat, gently try to move it for-
ward and backward to check that it is securely re-
tained. Seat and seat belts
2-08
2
Presented by http://mmc-manuals.ru/ \251