2010 MITSUBISHI GRANDIS radio

To listen to the radio
E00709000678
1. Press
the PWR switch (5) to turn the audio
system ON and OFF. The system turns on in
the last mode used.
2. Press the AM/FM button (1) to select the de- sired band.
3. Press the TUNE/SEEK button (2 or 3) to turn to a station, or press one of the memory
select buttons (4) to recall a station memo-
rised for that button.
To tune the radio E00709100565
Automatic tuning
After
keeping the TUNE/SEEK button (2 or 3) de-
pressed until it beeps, release the button, and the se-
lected station reception will start.
Manual tuning
The frequency changes every time the TUNE/
SEEK button (2 or 3) is pressed. Press the button to
select the desired station. To enter frequencies into the memory
E00716100785
Manual setting
You

can assign to the memory select buttons (4) a
maximum of 18 stations in the FM band (6 FM1, 6
FM2 and 6 FM3 stations) and 6 stations each in the
MW and LW band. (Stations already assigned to
the memory select buttons are replaced by any new-
ly assigned stations.) Follow the steps described below.
1. Press
either the TUNE/SEEK button (2 or 3)
to tune the frequency to be entered in the mem-
ory.
2. Press one of the memory select buttons (4) for 2 seconds or longer. The sound will be
momentarily interrupted while the frequency
is being entered into the memory.
The number of the button corresponding to
the entry in the memory and the frequency
are displayed. 3. The
preset memory setting is retrieved by
pressing the button and then releasing it with-
in 2 seconds.
Automatic setting
With the method, all manually set stations in the
band currently selected for reception are replaced
with stations in the same band that are automatical-
ly selected in order of signal strength. The radio au-
tomatically selects 6 stations in the FM band (FM3
station only) and 6 stations each in the MW and
LW band.
Follow the steps described below. 1. With the radio mode selected, hold down theAM/FM button (1) for 2 seconds or longer.
The 6 stations with the best signal strength
will automatically be assigned to the memo-
ry select buttons (4), with the lowest-frequen-
cy station being assigned to the lowest-num-
ber button.
2. When you subsequently press a memory se- lect button to select a channel number, the ra-
dio will begin receiving the station assigned
to that number.
NOTE l If you press the AM/FM button (1) for 2 sec-
onds or longer while tuning in the FM1 or
FM2 band, the radio will automatically
switch to the FM3 band, where the automatic
seeking/storing will be activated. For pleasant driving
5-17 5
Presented by http://mmc-manuals.ru/ \251

Radio data system (RDS)
E007092002471- AM/FM (FM/MW/LW selection) button
2-
Menu button
3- Memory select buttons
4- PWR (On-Off) switch
5- TUNE/SEEK (Down-step/Down-seek) button
6- TUNE/SEEK (Up-step/Up-seek) button
7- TP (Traffic program) button
8- PTY (Program type) button 9- AF (Alternative frequencies) indicator
10- RDS (Radio data system) indicator
11- REG (Regional program) indicator
12- TP (Traffic program identification) indicator
13- PTY (Program type) indicator
14- CT (Clock time) indicator
15- Frequency display window
RDS uses PI (program identification) signal and AF (alternative frequency) list transmitted in addition to the normal FM broadcasting programs, and picks up the
FM
stations that are transmitting the same program from the EON (enhanced other network) and automatically tunes to the station with the strongest signal intensity.
Therefore, you can continue listening to one program in, for example, a long distance driving without retuning to the other station transmitting the same program
when you are leaving the service area of the currently receiving station.
The RDS radio also features the limited reception of the program types, the break-in reception of the traffic announcement and emergency broadcast, and the limited/
unlimited reception of the regional programs. For pleasant driving
5-18
5
Presented by http://mmc-manuals.ru/ \251

AF (Alternative Frequencies) function
E00720900016
The
AF function finds a station broadcasting the
same program and selects the station with the stron-
gest signal of AF lists.
The AF function is turned on (with the AF indica-
tor (9) shown on the display) at all times unless
you manually switch it off.

The AF function can be turned ON and OFF.
Refer to “Function setup mode” on page 5-21.
CT (Clock Time) function E00721000014
The clock can be set automatically by using the sig-
nal

from the local RDS stations. Refer to “Digital
clock” on page 3-10.
REG (Regional) function E00721100015
REG function limits to receive the stations broad-
casting regional programs.
Regional

programming and regional networks are
organized differently depending on the country or
area (they may be changed according to the hour,
state, or broadcast area), so if you don’t want to re-
ceive the regional programs automatically, you can
set up REG ON not to receive regional programs.

The REG function can be turned ON and OFF.
Refer to “Function setup mode” on page 5-21.
PI (Program Identification) search function E00721200016
When travelling long distance and the recalled pre-
set

station is weak, the radio searches another fre-
quency broadcasting the same programming with
the same PI code in AF list. If there are no frequencies broadcasting the same
programming,

the radio searches a frequency broad-
casting the regional programming. The radio suc-
ceeds in searching the regional programming, then
the display shows the REG indicator (11).
If the radio does not succeed in searching the re-
gional programming, the radio returns to the recal-
led preset station.
PTY (Program type) E00721300192
RDS broadcasts are classified according to pro-
gram

type (PTY) as follows. Use the TUNE/SEEK
button (5 or 6) to select your desired PTY. 1. NEWS
2. AFFAIRS (Current affairs)
3. INFO (Information)
4. SPORT
5. EDUCATE (Education)
6. DRAMA
7. CULTURE
8. SCIENCE
9. VARIED
10. POP M (Pop music)
11. ROCK M (Rock music)
12. EASY M (Easy music)
13. LIGHT M (Light classics)
14. CLASSICS
15. OTHER M (Other music)
16. WEATHER (Weather information)
17. FINANCE
18. CHILDREN
19. SOCIAL
20. RELIGION
21. PHONE IN
22. TRAVEL
23. LEISURE
24. JAZZ
25. COUNTRY
26. NATION M (National music) 27. OLDIES
28.

FOLK M (Folk music)
29. DOCUMENT
To search for a broadcast of desired program type: 1. Press the PTY button (8).
2. Press the TUNE/SEEK button (5 or 6) forless than 1 second at a time to select your de-
sired PTY.
3. Two seconds after a desired PTY has been se- lected, the radio will begin to search for a
broadcast of your selected PTY. During
search, the selected PTY on the display
blinks and the radio will begin to search for a
broadcast of your selected PTY.
4. When the radio picks up a station with your desired PTY, the display will show the name
of the station. NOTE
l If

the TUNE/SEEK button (5 or 6) is pressed
for more than 1 second, the radio will try to
find out another broadcast of the same pro-
gram type as currently selected. For pleasant driving
5-19 5
Presented by http://mmc-manuals.ru/ \251

l
If no station is found with your desired PTY,
the display will show “EMPTY” for about 5
seconds and the radio will return to the previ-
ous station.
How to enter PTYs in the memory E00721400122
As many as 6 PTYs can be entered in the memory.
Follow the steps described below.
1. Press

either the TUNE/SEEK button (5 or 6)
to tune the PTY to be entered in the memory.
2. Press one of the memory select buttons (3) for 2 seconds or longer. The sound will be
momentarily interrupted while the PTY is be-
ing entered into the memory. The number of
the button corresponding to the entry into the
memory and the PTY are displayed.
3. The preset memory setting is retrieved by pressing the button and then releasing it with-
in about 2 seconds.
To change the language of PTY display E00721500181
You can select your favourite language among Eng-
lish,

French, German, Swedish, Spanish and Italian.
1. Press the “MENU” button (A) to select the language of PTY display mode.
Refer to “Function setup mode” on page
5-21.
2. Press the audio adjust button (B) to select a language.
NOTE l After selecting a mode, you can leave the func-
tion setup mode by taking either of the fol-
lowing steps: • Press
the “MENU” button for at least 2
seconds.
• Make no entry for 7 seconds. Traffic information
E00721600179
The radio will automatically tune in to traffic infor-
mation

broadcasts while receiving FM broadcasts
or playing compact discs.
To select this function, follow the instructions below. 1. Press
the TP button (7). The display will
show “TP” (12). If the RDS data can be read,
the display will show “RDS” (10). If not, the
display will show “NO RDS” for about 5 sec-
onds.
2. If the radio detects traffic information on ei- ther the station currently selected or another
station, the display will show “TRAF INF”
for 5 seconds followed by a 2-second indica-
tion of the frequency. Then, it will show the
name of the station broadcasting the traffic in-
formation to which you will listen. The vol-
ume level is set separately for listening to nor-
mal audio programs and for listening to traf-
fic information. The volume level will there-
fore change automatically to that set when
traffic information was last received. When
the traffic information broadcast is over, the
radio will return to the previously received
program and to the corresponding volume lev-
el.
3. Press the TP button (7) to return to the previ- ous condition.
NOTE l While “TP” is illuminated, the radio stops on-
ly at TP stations even if the TUNE/SEEK but-
ton (5 or 6) is pressed. For pleasant driving
5-20
5
Presented by http://mmc-manuals.ru/ \251

TP (Traffic information Program) search function
E00721800012
The traffic information program standby function
is
turned on (with the TP indicator (12) shown on
the display) and after about 45 seconds since the
RDS indicator (10) turns off due to weak signal or
the tuning station is changed over from a TP sta-
tion to a station which does not broadcast traffic in-
formation, the sound will beep 5 times and seeks
out a TP station in all frequencies automatically. The TP search function can be turned ON and OFF.
Refer to “Function setup mode” on page

5-21.
Emergency broadcasts E00721700011 If an emergency broadcast is caught while receiv-
ing

a FM broadcast or playing back a compact disc
with the ignition switch in “ACC” or “ON” posi-
tion, the display will show “ALARM” and the emer-
gency broadcast will interrupt the current program.
The volume level is set separately for listening to
normal audio programs and for listening to emer-
gency broadcasts. The volume level will therefore
change automatically to that set when an emergen-
cy broadcast or traffic information broadcast was
last received. When the emergency broadcast is
over, the radio will return to the previously re-
ceived program and to the corresponding volume
level.
Function setup mode E00722500175
It is possible to change the following functions: l
AF
l CT
l REG
l TP-S
l Language of PTY display
1. Press

the “MENU” button to select the func-
tion setup mode. For pleasant driving
5-21 5
Presented by http://mmc-manuals.ru/ \251

To listen to a CD
E00709601004
With a CD player
1.
Insert disc with label facing up.When a disc is inserted, the CD indicator
(16) will come on and the CD player will be-
gin playing even if the radio is being used.
The CD player will also start playback when
the CD button (8) is pressed with a disc in
the player even if the radio is being used.
NOTE l If the system is equipped with a CD autoch-
anger, the system switches between the CD
player mode and the CD autochanger mode
each time the CD button (8) is pressed.
2. To adjust the volume and tone, refer to “To adjust the volume” on page 5-15 and “To ad-
just the tone” on page 5-15.
NOTE l When an 8 cm compact disc is used, the adapt-
er is not needed for playback. Insert the disc
in the centre of the disc-loading slot.
l For information concerning the handling of
compact discs, refer to “Handling of compact
discs” on page 5-30.
To fast-forward/fast-reverse the disc
To fast-forward or fast-reverse the disc, press the
TRACK button (5).
Fast-forward
You can fast-forward the disc by pressing the side of the TRACK button (5). While the button is
kept pressed, the disc will be fast-forwarded.
Fast-reverse You can fast-reverse the disc by pressing the side of the TRACK button (5). While the button is
kept pressed, the disc will be fast-reversed.
NOTE
l When
you have fast-forwarded/fast-reversed
the disc, the playing-time may be shown
with deviation.
To listen to an MP3 CD
This CD player allows you to play MP3 (MPEG Au-
dio Layer- 3) files recorded on CD-ROMs, CD-Rs
(recordable CDs), and CD-RWs (rewritable CDs)
in ISO9660 Level 1/Level 2, Joliet, and Romeo for-
mats. Each disc may have a maximum of 16 trees,
100 folders, and 255 files per disc. During MP3
playback, the unit can display ID3 tag information.
For information concerning ID3 tag, refer to “CD
text and MP3 title display” on page 5-26. 1. Insert
a disc containing MP3 files into the slot.
2. Press the CD button (8) for 2 seconds or lon-
ger to switch to MP3 CD mode from normal
music CD mode. The display shows “READ-
ING”, then playback will begin. The folder
number and the track number will appear on
the display. NOTE
l While

listening to a disc on which CD-DA
(CD-Digital Audio) and MP3 files have both
been recorded, you can switch between read-
ing of the CD-DA, reading of the MP3 files,
and AUX (auxiliary input) by pressing the
CD button for 2 seconds or longer (until you
hear a beep).
l With a disc that contains both CD-DA and
MP3 files, the CD-DA files are automatical-
ly played first.
l The playback sound quality differs depend-
ing on the encoding software and the bit rate.
For details, refer to the user manual of your
encoding software.
l Depending on file/folder configurations on a
disc, it may take some time before playback
starts.
l MP3 encoding software and writing software
are not supplied with this unit.
l You may encounter trouble in playing an
MP3 or displaying the information of MP3
files recorded with certain writing software
or CD recorders (CD-R/RW drivers).
l If you record too many folders or files other
than MP3 onto a disc, it may take some time
before playback starts.
l This unit does not record MP3 files.
l For information concerning CD-Rs/RWs, re-
fer to “Notes on CD-Rs/RWs” on page 5-31. For pleasant driving
5-24
5
Presented by http://mmc-manuals.ru/ \251

NOTE
l The
repeat mode will be cancelled by press-
ing the TRACK button (5), the SCAN button
(6) or CD eject button (1).
l With a disc that contains both CD-DA and
MP3 files, the repeat mode causes only files
of the same format (CD-DA only or MP3
files only) to be repeated.
To change the order of tracks for playback
Random playback for a disc (music CDs only)
Press the RPT/RDM button (14) briefly. “RDM”
will appear on the display. Tracks on the currently
selected disc will be played in a random sequence.
To exit the random mode, press the RPT/RDM but-
ton again.
Random playback for all folders on a disc (MP3
CDs only)
Press the RPT/RDM button (14) briefly. “RDM”
will appear on the display. Tracks in the currently
selected disc will be played in a random sequence.
To exit the random mode, press the RPT/RDM but-
ton again. NOTE
l The
random mode will be cancelled by press-
ing the SCAN button (6) or the CD eject but-
ton (1).
l With a disc that contains both CD-DA and
MP3 files, the random mode causes only
files of the same format (CDDA only or
MP3 files only) to be played in a random se-
quence.
To find the start of each track on a disc for playback
Press the SCAN button (6). “SCAN” will appear
on the display and the CD player will play back the
first 10 seconds of each track on the selected disc.
The track number will blink while the scan mode is
selected. To exit the scan mode, press the SCAN
button again.
NOTE l Once all tracks on the disc have been scan-
ned, playback of the disc will restart from the
beginning of the track that was playing when
scanning started.
l The scan mode will be cancelled by selecting
the RPT/RDM button (14), the TRACK but-
ton (5) or the CD eject button (1).
l With a disc that contains both CD-DA and
MP3 files, the scan mode causes only files of
the same format (CD-DA only or MP3 files
only) to be played.
To eject a disc
When the CD eject button (1) is pressed, the disc
automatically stops and is ejected. The system auto-
matically switches to radio mode. CD text and MP3 title display
E00725000298
This
CD player can display CD text and MP3 titles
including ID3 tag information.
CD text
The CD player can display disc and track titles for
discs encoded with disc and track title information.
Press the TEXT button (9) repeatedly to make se-
lections in the following sequence: disc name track name normal display mode.
Disc
name
Track name
Normal display mode NOTE
l The

display can show up to 10 characters. If
a disc name or track name has more than 10
characters, press the PAGE button (11) to
view the next 10 characters.
l When there is no title information to be dis-
played, the display shows “NO TITLE”. For pleasant driving
5-26
5
Presented by http://mmc-manuals.ru/ \251

l
Characters that the CD player cannot display
are shown as an asterisk.
MP3 title
The CD player can display folder and track titles
for discs encoded with folder and track informa-
tion. Press the TEXT button (9) for less than 1 sec-
ond repeatedly to make selections in the following
sequence: folder name track name normal
display mode. ID3 tag information
The

CD player can display ID3 tag information for
files that have been recorded with ID3 tag informa-
tion. 1. Press the TEXT button (9) for 2 seconds orlonger to switch to the ID3 tag information.
“TAG” indicator will appear on the display. 2. Then
press the DISP button for less than 1
second repeatedly to make selections in the
following sequence: album name track
name artist name normal display mode.
NOTE l To

return from ID3 tag information to the
folder name, press the TEXT button (9)
again for 2 seconds or longer.
l When there is no title information to be dis-
played, the display shows “NO TITLE”.
l The display can show up to 10 characters. If
a folder name, track name, or item of ID3 tag
information has more than 10 characters,
press the PAGE button (11) to view the next
10 characters.
l Folder names and track names can each be
displayed up to a length of 10 characters.
Items of ID3 tag information can each be dis-
played up to a length of 10 characters.
l Characters that the CD player cannot display
are shown as an asterisk.
With a CD autochanger 1. Press the CD button (11), and the CD autoch-anger mode will be selected, starting playback.
2. To adjust the volume and tone, refer to “To adjust the volume” on page 5-15 and “To ad-
just the tone” on page 5-15.
3. To stop the CD player, turn off the power by pressing the PWR switch (13) or switch to
the radio mode by pressing the AM/FM but-
ton (7).
4. For information concerning the handling of compact discs, refer to “Handling of compact
discs” on page 5-30.
To select a desired disc (CD autochanger only)
You can select by using the DISC button (10 or 12). Disc up
Press

the DISC button (12) until the desired disc is
reached. The disc indicator (16) will display the se-
lected disc number.
Disc down
Press the DISC button (10) until the desired disc is
reached. The disc indicator (16) will display the se-
lected disc number. For pleasant driving
5-27 5
Presented by http://mmc-manuals.ru/ \251