2010 MITSUBISHI GRANDIS warning

Card holder (RHD vehicles only)
E00718800076
To
store a card, insert it into the card holder until
you hear a click. To remove the card, give it a
push. It will come out automatically. NOTE
l The card holder can hold up to 3 cards.
l Do

not insert receipts and other thin pieces
of paper. Personal table*
E00715300041
To

use the personal table, push the button (A) and
pull the table up until it locks in position. WARNING
l Keep the table retracted while driving the
vehicle.

The table could otherwise cause
an accident in the event of hard braking
or a collision.
l When retracting the table, push it until a
click is emitted from the vicinity of the but-
ton. Confirm that the table is securely re-
tained.
NOTE l Make sure the table is level before using it.
l Do

not place luggage weighing a total of 4
kg or more on the table.
l Keep the table retracted when you are not us-
ing it. Tonneau cover*
E00715500463
To install 1. Remove

the tonneau cover, which is stowed
in the luggage area, from its storage bag.
2. Stow the third seat (Refer to “Stowing the third seat” on page
2-13.)
3. Move the sliders (A) outward to the posi- tions where they click, then check that they
are securely locked in position. For pleasant driving
5-42
5
Presented by http://mmc-manuals.ru/ \251

3. Put the tonneau cover in its storage bag and
stow it in the luggage area. CAUTION
l
Be sure to stow the tonneau cover as illus-
trated.

Unless stowed in the correct posi-
tion, the tonneau cover could touch the
seat belts and damage them. Assist grip
E00732800227
These

grips are to support the body by hand while
seated in the vehicle. CAUTION
l
Do
not use the assist grips when getting in-
to or out of the vehicle.
The assist grips could detach and cause
an accident. Coat hooks*
E00725600555
There

are two hooks on the rear pillar for use in
hanging clothes. WARNING
l Do
not put a hanger or any heavy or poin-
ted object on the coat hook. If the curtain
airbag was activated, any such item could
be propelled away with great force and
could prevent the curtain airbag from in-
flating correctly. Hang clothes directly on
the coat hook (without using a hanger).
Make sure there are no heavy or sharp ob-
jects in the pockets of clothes that you
hang on the coat hook. For pleasant driving
5-44
5
Presented by http://mmc-manuals.ru/ \251

Luggage hooks
E00715700090
There
are 4 luggage hooks at the sides of the lug-
gage area. Use them when you wish to tie luggage
down. CAUTION
l
Be
sure to tie luggage down securely. Oth-
erwise, hard braking could cause luggage
to be thrown into the passenger area, re-
sulting in an accident. Cargo net*
E00715800118
To

use, attach the net to the hooks according to the
illustration. The cargo net is used to cover light arti-
cles in the luggage compartment to prevent them
from tumbling. Warning triangle retaining bands
E00715200079
Band
(B) to be used for retaining a warning trian-
gle can be accessed with the third seat stowed and
the luggage floor board (A) raised. (Refer to “Stow-
ing the third seat” on page 2-13.) NOTE
l Some

warning triangle may not fit fully into
the storage space and may thus be damaged
by the third seat. For pleasant driving
5-45 5
Presented by http://mmc-manuals.ru/ \251

If the vehicle breaks down
E00800100778
If
the vehicle breaks down on the road, move it to
the shoulder and use the hazard warning flashers and/
or the warning triangle etc.
Refer to “Hazard warning flasher switch” on page
3-21.
If the engine stops/fails
Vehicle operation and control are affected if the en-
gine stops.
Before moving the vehicle to a safe area, be aware
of the following:
l The brake booster becomes inoperative and
the pedal effort will increase. Press down the
brake pedal harder than usual.
l Since the power steering pump is no longer
operative, the steering wheel feels heavy
when turning it. Turn the wheel with more ef-
fort than usual. Emergency starting
E00800502301
If
the engine cannot be started because the battery
is weak or dead, the battery from another vehicle
can be used with jumper cables to start the engine. WARNING
l To
start the engine by use of jumper ca-
bles from another vehicle, perform the cor-
rect procedures according to the instruc-
tion manual. Incorrect procedures could
result in a fire or explosion or damage to
the vehicles.
1. Get
the vehicles close enough so the jumper cables can reach, but be sure the vehicles
aren’t touching each other. If they are, it
could cause a ground connection you don’t
want. The vehicle will not start, and the bad
grounding could damage the electrical sys-
tems. CAUTION
l
Check
the other vehicle. It must have a 12-
volt battery.
If the other system isn’t 12-volt, shorting
can damage both vehicles.
2. You
could be injured if the vehicles move. Set the parking brake firmly on each vehicle.
Put an A/T in “P” (PARK) or a M/T in “N”
(Neutral). Turn off the ignition switch. WARNING
l Turn
off the ignition on both vehicles be-
forehand. Take care to make sure that
the cables or your clothes are never
caught by the fan or drive belt. Personal
injury could result.
NOTE l Turn

off all lamps, heater and other electrical
loads. This will avoid sparks and help save
both batteries.
3. Make sure battery electrolyte is at the proper level. Refer to “Battery” on page 8-10. WARNING
l If
electrolyte fluid is not visible, or ap-
pears to be frozen, Do Not Attempt Jump
Starting!
A battery might rupture or explode if the
temperature is below the freezing point
or if it is not filled to the proper level.
4. Connect the booster battery. Petrol-powered vehicles
Connect

one end of one jumper cable to the
positive (+) terminal of the discharged bat- For emergencies
6-02
6
Presented by http://mmc-manuals.ru/ \251

tery (A), and the other end to the positive (+)
terminal of the booster battery (B).
Diesel-powered vehicles (except for diesel
particulate filter models)
Lift
up the front of the engine cover to re-
lease the three grommets (A). Then, pull the
engine cover towards you to release the grom-
met (B) and remove the cover. Diesel-powered vehicles (for diesel particu-
late filter models) Lift up the engine cover to release the five
grommets (A) and remove the cover.
Connect one end of one jumper cable to the
positive
(+) terminal of the discharged bat-
tery (A), and the other end to the positive (+)
terminal of the booster battery (B). 5. Connect
one end of the other jumper cable to
the negative (-) terminal of the booster bat-
tery, and the other end to the engine block of
the vehicle with the discharged battery at the
point farthest from the battery. NOTE
l Open

the cover before connecting the jumper
cable to the positive (+) terminal of the bat-
tery. (Refer to “Battery” on page 8-10.) WARNING
l Be
sure to observe the connecting se-
quence of .
l Make sure that the connection is made
to

the appointed position (shown in the il-
lustration). If the connection is made di-
rectly to the negative side of the battery,
the inflammable gasses generated from
the battery might catch fire and explode.
l When connecting the jumper cable, do
not connect the positive (+) cable to the
negative (-) terminal. Otherwise sparks
might cause explosion of the battery. CAUTION
l
Take
care not to get the jumper cable
caught in the cooling fan or other rotat-
ing part in the engine compartment.
l Take care not to pinch the wiring harness
with the clamps when connecting the
jumper cables.
l Use the proper cables suitable for the bat-
tery size. Otherwise heat damage to the ca-
bles could result.
l Check the jumper cables for damage and
corrosion before use.
6. Start
the engine in the vehicle which has the booster battery, let the engine idle a few mi- For emergencies
6-03 6
Presented by http://mmc-manuals.ru/ \251

nutes, then start the engine in the vehicle
with the discharged battery.
CAUTION
l
Keep the engine of the vehicle giving assis-
tance running.
7. After
the engine is started, disconnect the ca- bles in the reverse order. WARNING
l Charging
the battery while it is installed
in the vehicle might cause the battery to
catch fire and explode. Or damage to the
vehicle could result. If it has to be charg-
ed in that condition for unavoidable rea-
sons, disconnect the vehicle side negative
(-) terminal connected to the battery.
l Keep sparks, cigarettes and flames away
from the battery because the battery may
produce an explosion.
l Use adequate ventilation when charging
or using the battery in an enclosed space.
l Remove all the caps before charging the
battery.
l Electrolyte is corrosive diluted sulphuric
acid.
If electrolyte (battery acid) comes into con-
tact with your hands, eyes, clothes and
the painted surface of your vehicle, it
should be thoroughly flushed with water.
If electrolyte gets in your eyes, flush them
with water immediately and thoroughly,
and get prompt medical attention. CAUTION
l
Do
not attempt to start the engine by pull-
ing or pushing the vehicle.
It could damage your vehicle.
l Always wear protective eye goggles when
working near the battery.
l Keep the battery out of the reach of chil-
dren.
NOTE l If

the vehicle is put in motion without fully
charging the battery, it might cause the loss
of smooth engine operation and the anti-lock
brake warning lamp to illuminate. Refer to
“Anti-lock brake system (ABS)” on page
4-21. Engine overheating
E00800602126
If

the water temperature gauge indication remains
in the overheating zone for a long time, the engine
may be overheating. If this occurs, take the follow-
ing corrective measures: 1. Stop the vehicle in a safe place.
2. Check whether steam is coming from the en-gine compartment.

[If steam does not come from the engine com-
partment]
With the engine still running, raise the bon-
net to ventilate the engine compartment.

[If steam is coming from the engine compart-
ment]
Stop the engine, and when the steam stops,
raise the bonnet to ventilate the engine com-
partment. Restart the engine. WARNING
l Do
not open the bonnet while steam is com-
ing from the engine compartment. It
could cause steam or hot water to spurt
out, causing burns. Hot water could spurt
out even when there is no steam coming
out, and some parts will be very hot. Be
very careful when opening the bonnet.
l Be careful of hot steam, which could be
blowing off the reserve tank cap.
l Do not attempt to remove the radiator
cap (petrol-powered vehicles) or reserve
tank cap (diesel-powered vehicles) while
the engine is hot. For emergencies
6-04
6
Presented by http://mmc-manuals.ru/ \251

3. Confirm that the cooling fans are turning. If
the fans are not turning, stop the engine im-
mediately and have it checked.
Petrol-powered vehicles
Diesel-powered vehicles A- Cooling fans
B- Radiator cap
C- Reserve tank lid
D- Reserve tank cap
*: Front of the vehicle
WARNING
l Be
careful not to get your hands or
clothes caught in the cooling fans. 4. After
the engine coolant temperature has drop-
ped to the normal temperature, stop the engine. 5. Check the coolant level in the reserve tank.
Petrol-powered vehicles
The

reserve tank lid (C) is equipped with a
dipstick.

Remove the dipstick and wipe it with a clean
cloth. Reinsert the dipstick as far as it goes.
Remove the dipstick and read the coolant lev-
el, which should always be within the range
indicated.
FULL
LOW WARNING
l If
there is none, make sure that the en-
gine has cooled down before removing
the radiator cap (B), because hot steam
or boiling water otherwise will gush from
the filler port and may scald you.
Diesel-powered vehicles
The
coolant level in this tank should be kept
between the “LOW” and “FULL” marks.
FULL
LOW WARNING
l If
there is none, make sure that the en-
gine has cooled down before removing
the reserve tank cap (D), because hot
steam or boiling water otherwise will
gush from the filler port and may scald
you.
6. Add
coolant to the radiator and/or reserve tank if necessary. (Refer to the “Mainte-
nance” section.) For emergencies
6-05 6
Presented by http://mmc-manuals.ru/ \251

3. Retract the jack, then remove it from its stor-
age location. To store
1. Retract
the jack, then return it to its original
position.
To retract
To expand 2. Expand the jack to lock it securely in place.
3. Return

the luggage floor board to its original
position. Jacking up the vehicle
E00801001393
1.

Park the vehicle on level and stable ground.
2. Set the parking brake firmly.
3. On vehicles with M/T, turn the ignition key to the “LOCK” position, move the gearshift
lever to the “R” (Reverse) position.
On vehicles with A/T, move the selector lev-
er to the “P” (PARK) position, turn the igni-
tion key to the “LOCK” position.
4. Turn on the hazard warning flashers and set up a warning triangle, flashing signal lamp,
etc., at an adequate distance from the vehi-
cle, and have all your passengers leave the ve-
hicle.
5. To prevent the vehicle from rolling when it is raised on the jack, place chocks or blocks
(A) at the tyre that is diagonally opposite
from the tyre (B) you are changing. WARNING
l Be
sure to apply chocks or blocks to the
correct tyre when jacking up the vehicle.
If the vehicle moves while jacked up, the
jack could slip out of position, leading to
an accident.
NOTE l The

chocks shown in the illustration do not
come with your vehicle. It is recommended
that you keep one in the vehicle for use if nee-
ded.
l If chocks are not available, use stones or any
other objects that are large enough to hold
the wheel in position.
6. Place the jack under one of the jacking points (C) shown in the illustration. Use the
jacking point closest to the tyre you wish to
change. For emergencies
6-07 6
Presented by http://mmc-manuals.ru/ \251