2010 MERCEDES-BENZ E-CLASS CABRIOLET door lock

Displa
ymessages Possible causes/consequences and
M Solutions
J EB
D, ABS
and ESP
inopera‐
tiv eS ee
Owner's
Manual G
Risk of accident
EBD (Electronic Brake-for ceDistribution), ABS, ESP ®
,B AS,
PRE-SAFE ®
,t he HOL Dfunction ,hill start assist and ESP ®
trailer stabilisation are no tavailab ledue to amalfunction. In
addition, the ä,åand! warning lamp sinthe
instrumen tcluster light up and awarning tone sounds.
ATTENTION ASSIST is deactivated.
The brake system continue stofunction normally, but without
the functions listed above. The wheels coul dtherefore lock if
you brake hard, for example.
X Drive on carefully.
X Visit aquali fieds pecialist workshop immediately. J Release
parking
brake You are drivin
gwith the parkin gbrake engaged .Awarning
ton ealso sounds.
X Release th eparking brake. J Br
ake
immedi‐
ately Am
alfunction has occurred while the HOL Dfunction or DIS-
TRONI CPLUSisa ctive.
or
Vehicles with manual transmissio n:with the HOL Dfunction
activated, you have either:
R opened the driver' sdoor and released th eseat belt or
R switched off th eengineor
R opened th ebonnet
At one ma yalso sound at regular intervals. The ton ebecomes
louder if you attempt to lock the vehicle.
You can notstart the engine.
X Paying attention to the traffic situation, immediately
depress the brake peda lfirmly and hold until the display
message disappears.
X Prevent the vehicle from rolling away before you leave it
(Y page 153).
You can restart the engine. 216
Display messagesOn-board computer and displays
BA 20
7ECE ÄJ 2010 /1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 216

Tyres
Display messages Possible caus
es/consequences andM Solutions
Tyre pres‐
sure Check
tyres
G
Ris
kofa ccident
The tyr epressure loss warning system ha sdetected asignif-
ican tloss in pressure.
Aw arning ton ealso sounds.
X Stop th evehicle without making any sudde nsteering or
braking mano euvres.P ay attention to the traffic conditions
as you do so.
X Check the tyres and, if necessary ,change the wheel
(Y page 302).
X Chec kthe tyr epressure and ,ifnecessary, correc tthe tyre
pressure.
X Restart the tyr epressure loss warning system when th etyre
pressure is correct (Y page 301).Check
tyr
epres‐
sures then
restart
Run Flat
Indicator Ad
isplay message for the tyre pressure loss warnin gsystem
was shown.
X Set the cor recttyrep ressur eina ll four tyres.
X Restart th etyrep ressur eloss war ningsystem
(Y page 301). Ru
nF lat
Indicator inopera‐
tive Th
et yrep ressur eloss war ningsystem is faulty.
X Visit aq ualified specialist workshop. Vehicle
Display messages Possible causes/consequences and
M Solutions
To st
art
engine, shift to
either P
or N Yo
uh avea ttempted to startthe engin ewitht he transmiss ion
in position Ror D.
X Shift th etransmission to position Por N. P Select
Park (P) You have switched off the engine with the Star
t/Stop button
and opened the driver's door.
You wante dtolock the vehicle.
Aw arning ton ealso sounds.
X Shift th etransmissio ntoposition P. 230
Display messagesOn-boar
dcomputer and displays
BA 20 7ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 230

Displa
ymessages Possible causes/consequences and
M Solutions
P Se
lect
Par k( P) While the HOLD functio
norDISTRONIC PLUSisa ctive, you
have:
R opened the driver's door and releasedthe sea tbelt or
R switched off the engin eor
R opened the bonnet
At one ma yalso sound at regular intervals. The ton ebecomes
louder if you attempt to lock the vehicle.
You can notstart the engine.
X Shift the transmission to position P.
You can restart the engine. Auxiliary
battery malfunc‐
tion The auxiliary battery for the automatic transmission is no lon-
ger being charged.
X
Visit aqualified specialist workshop. N The boot lid is open.
X
Close the boot lid. M G
Risk of accident
The bonnet is open. Awarning ton ealso sounds.
X Pull ove rand sto pthe vehicle safel yassoonasp ossible,
paying attention to roa dand traffic conditions.
X Engag ethe parkin gbrake.
X Close th ebonnet.
If the active bonnet (pedestrian protection) has been trig-
gered:
X Reset the bonnet (Y page 258).
X Close the bonnet. Active
bonnet malfunc‐
tion See
Owner's
Manual The active bonnet (pedestrian protection) is not active due to
am
alfunction.
X Visit aqualified special istworkshop. C At least one door is open.
Awarning ton ealso sounds.
X Close all doors. Display messages
231On-boardcomputer and displays
BA 20 7ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 231 Z

Displa
ymessages Possible causes/consequences and
M Solutions
+ Ke
yn ot
detected
(red display
message) Th
eK EYLESS-GO key is not in the vehicle.
Aw arning ton ealso sounds.
If th eengineiss witched off ,you can no longer loc kthe vehicle
cen trally or start the engine.
X Pull over and stop the vehicle safely as soon as possible,
paying attention to road and traffic conditions.
X Engage the parkin gbrake.
X Locate th eKEYLESS-GO key. The KEYLESS-GO key is not detected whil
ethe engin eisrun-
ning because there is interference from astron gsource of
radio waves.
Aw arning ton ealso sounds.
X Pull ove rand sto pthe vehicle safel yassoonasp ossible,
paying attention to roa dand traffic conditions.
X Engag ethe parkin gbrake.
X Operate th evehicle with the key in the ignition lock if nec-
essary. + Ke
yn ot
detected
(white dis-
play mes-
sage) Th
eK EYLESS-GO key cannot be detected at present.
X Chang ethe location of the key with the KEYLESS-GO func-
tion sint he vehicle.
If the KEYLESS-GO key is still not detected:
X Change the location of the key with the KEYLESS-GO func-
tion sint he vehicle.
X Operate the vehicle with the key in the ignition lock if nec-
essary. + Ke
ys till
in vehicle Th
eK EYLESS-GO key has bee ndetected inside the vehicle
during locking.
X Remov ethe KEYLESS-GO key from the vehicle. + Remove
starting
button,
then
insert key KEYLESS-GO is temporarily malfunctioning or is defective
.A
warning tone also sounds.
X Insert the key into the ignition lock and turn it to the desired
position.
X Visit aqualified special istworkshop. + Close
door
sto
lock vehi‐
cle At leas
tone doo risopen. Awarning ton ealso sounds.
X Close all door sand lock the vehicle again. Display messages
235On-board computer and displays
BA 207ECE ÄJ 2010 /1a;1;2,e n-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 235 Z

Examp
le:C oupé
: Mirror light
; Bracket
= Retainin gclip, e.g .for ac ar park ticket
? Vanity mirror
A Mirror cover
Vanity mirro rint he sun visor Mirror light
:onlyfun ctions if the su nvisor
is clipped into retainer ;and mirror cover
A hasb eenf olded up.
Glare from th eside X
Fol dd ownthe sun visor.
X Pul lsun visor out of retainer ;.
X Swin gthe sun viso rtot he side. Rea
rwindow roller sunblind (Coupé)
To extend/retract th eroller sunblind G
Warning
When leavin gthe vehi cle, alway sremove the
key from the starter switch. Alway staket he
key with you and lock the vehi cle. Do not leave
children unattended in the vehicle, even if
the yare secured in achild restraint system.
Do not give the macces stoanu nlocked vehi-
cle .Ifu nsupervised children have access to a
vehicl ethis could resul tinanaccident and/
or seriou sinjury. The ycould:
R be seriously or even fatally injured on parts
of the vehicle
R be se riously or even fatally injure dbypro-
longed exposure to extremel yhigh or
extremely low temperatures
R caus eana ccidentby operating functions
such as seat adjustment, steering wheel
adjustmen tormemory functions, which
can be operate deven when the key has
been removed from the starter switch or
the vehicle.
If children open adoor, they coul dinjure other
persons or get out of the vehicl eand injure
themselves or be injured by following traffic.
Do not expose the child restraint system to
direct sunlight. The child restraint system's
metal parts, for example ,could becom every
hot and the child could suffer burn sasa
result.
! Make sure that th eroller sunblind can
mov efreely. Otherwise ,the roller sunblind
or other objec ts could be damaged. Features
251Loading, stowin gand features
BA 20 7ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 251 Z

thi
sreason, following acar wash, drive with
particular care unti lthe brakes are dry. G
Risk of accident
Th ev ehicle is braked when th eHOLDfunction
or DISTRONI CPLUSisa ctivated. Therefore,
dea ctivate th eHOLD function and DISTRONIC
PLU Sbefor ethe vehicle is washed in an auto-
matic car wash.
You can wash the vehicle in an automatic car
wash from the ver ystart.
! We recommend automatic car washes
with an adjustable 40
high-pressure pre-
cleaning program. In car washes that use
hig hw ater pressures, there is adanger that
as mall quantity of water may leak int othe
vehicle.
! Cabriolet: do not treat the vehicle with
hot wax under any circumstan ces.
! Cabriolet: pull the key out of the ignition
lock when washing the vehicle .This
ensures that the win ddeflector on the
windscreen is retracted. The wind deflector
may otherwise be damaged.
If the vehicle is ver ydirty, pre-wash it before
cleaning it in an automatic car wash.
! In car washes with atowing mechanism,
make sure that the automatic transmission
is in transmission position N,otherwis ethe
vehicle could be damaged.
! Make sur ethat the side windows ar ecom-
pletel yclosed, that the ventilation/heater
blowe risfully turned off and that the wind-
screen wiper switch is set to 0.Otherwi se,
the rain/light senso rmay be activated, trig-
gering unintended wiper movemen ts.T his
could cau se damage to the vehicle.
After using an automatic car wash, wip eoff
wax from th ewindscreen and the wiper
blades. This will prevent smears and reduce
wiping noises caused by residue on the wind-
screen. High-pressur
ecleaners G
Risk of accident
Do not use high-pressur ecleaners with circu-
lar-jet nozzles (dirt grinders) to clean your
vehicle, in particular the tyres. You could oth-
erwise damage the tyres and cause an acci-
dent.
! Always maintain adistance of at least
30 cm between the vehicle and the high-
pressure cleaner nozzle. Information about
the correct distance is available from the
equipment manufacturer.
Move the high-pressure cleaner nozzle
around when cleaning your vehicle.
Do not aim directly at any of the following:
R tyres
R door joint
R soft top (Cabriolet)
R wind deflector net (Cabriolet)
R electrical components
R battery
R connectors
R lights
R seals
R trim elements
R ventilation slots
Damaged seals or electrical components
can lead to leaks or failures.
Cleanin gthe whee ls !
Do not use acidic whee lcleaning products
to remov ebrake dust .This could damage
wheel bolts and brake componen ts.
! Do not park up the vehicle for an extended
perio dstraight after cleaning it, particularly
after having cleaned the wheels with wheel
cleaner. Wheel cleaners could cause
increased corrosio nofthe brake discs and
brake pads/linings. For this reason, you
should drive for afew minutes after clean-
ing. Brakin gheats the brak ediscs and
40 In accordance with the specification sfor Cabriolet programs. 264
CareMaintenance and care
BA 20
7ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 264

tha
tyou additionally equip your vehicle
with the TIREFI Tkit if you fit tyres that do
not featur erun-flat properties ,e.g. winter
tyres .You can obtain aTIREFIT kit from a
Mercedes-Benz Service Centre ,for exam-
ple.
X Stop the vehicle as far away as possible
from traffic on solid, non-slipper yand level
ground.
X Switch on the hazard warning lamps.
X Firmly depress the parking brake.
X Bring the front wheels into the straight-
ahead position.
X Vehicles with manua ltran smission:
engage first or reverse gear.
X Vehicles with au tomatic transmission:
move the selector lever to P.
X Switch off the engine.
X Vehicles without KEYLESS-GO: remove
the key from the ignition lock.
X Vehicles with KEYLESS-GO: openthe
driver's door.
The on-boar delectronics have status 0,
which is the same as the key having been
removed.
X Vehicles with KEYLESS-GO: removethe
Star t/Stop butto nfrom th eignition lock
(Y page 135).
X All occupan ts must get out of the vehicle.
Make sur ethat they ar enot endangered as
they get out of the vehicle.
X Make sure that no one is near the danger
area whilst awheel is being changed. Any-
one who is not directly assisting in the
wheel change should, for example, stand
behind the barrier.
X Get out of the vehicle. Pay attention to traf-
fic conditions when doing so.
X Close the driver's door.
X Plac ethe warnin gtriangl e(Ypage 273) a
suitable distanc eaway .Observ elegal
requirements. TIREFIT kit
Using th eTIREFIT kit You can use the TIREFIT kit to seal small
punctures, particularly those in the tyre tread.
You can use TIREFIT at outside temperatures
down to -20 †.
G
Risk of accident
In the following situations, your safety is at
particular risk and tyre sealant is unable to
provide breakdown assistance if:
R ther eare cuts or punctures in th etyre
greater than 4mm
R the whee lrim is damaged
R you have driven at very low tyre pressures
or on aflat tyre
Do not drive any fur ther. Consult aqualified
specialist workshop which has the necessary
specialist knowledg eand tool stocarry out
the work required.
Mercedes-Benz recommends that you use a
Mercedes-Benz Service Centr efor this pur-
pose. In particular ,work relevant to safet yor
on safety-related system smust be carried out
at aq ualified specialist workshop.
X Do not remov eany foreig nobjects which
have penetrated the tyre, e.g. screw sor
nails.
X Remove the TIREFI Tkit,t he accompanying
"max. 80 km /h"sticker and the electric air
pump from the stowage well underneath
the boo tfloor (Y page 274). 276
Flat tyreBreakdown assis
tance
BA 207ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:0
0-Seite 276