2010 JAGUAR XFR torque

15.
















16. CAUTION: Do not use air tools to install the nut.
Failure to follow this instruction may result in damage to
the component.
Torque: 300 Nm











Check and top-up the differential case.














17.
Install the LH rear wheel and tire.

Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

3. NOTE: Left-hand shown, right-hand similar.
















4. NOTE: Left-hand shown, right-hand similar.
5. NOTE: Left-hand shown, right-hand similar.
Torque: 58 Nm

6. NOTE: Left-hand shown, right-hand similar.

Secure the bottom arm of the anti-rattle spring
under the bottom anchor bracket of the caliper.
Compress the upper spring arm into the correct
position, under the upper anchor bracket, whilst
retaining the logo plate.
Using the screw-driver, tap the central locating tag
into the locked position.
















7. CAUTIONS:


Always plug any open connections to prevent
contamination.


Make sure new sealing washers are installed.

NOTES:


To prevent the loss of brake fluid, using the special
tool apply the brake pedal and set to 40mm ( 1.6 in ) below
the rest position.


Left-hand shown, right-hand similar.
Torque: 42 Nm www.JagDocs.com

Published: 11-May-2011
Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake Disc Vehicles With: High Performance Brakes
Removal and Installation

Removal


CAUTION: Brake discs must be renewed in pairs.


NOTE: Removal steps in this procedure may contain installation details.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Brake Pads - Vehicles With: High Performance Brakes (206-03B Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol,
Removal and Installation).

3. Torque: 115 Nm 4.
Remove the 2 clips.
Clean the components mating faces.













Installation 5. Repeat the above procedure on the opposite side.

1. To install, reverse the removal procedure.

5. NOTE: Left-hand shown, right-hand similar.

Torque: 10 Nm





















6. CAUTIONS:


Always plug any open connections to prevent
contamination.


If brake fluid is spilt on the paintwork, the affected
area must be immediately washed down with cold water.
NOTES:


To prevent the loss of brake fluid, using the special
tool apply the brake pedal and set to 40mm ( 1.6 in ) below
the rest position.


Left-hand shown, right-hand similar.
Torque: 42 Nm

Installation
9.

























10.
WARNING: If the brake caliper piston seal is damaged
a new brake caliper must be installed.


CAUTION: Do not allow the brake caliper to hang on
the brake hose.


NOTE: Left-hand shown, right-hand similar.

Torque: 28 Nm














NOTE: Left-hand shown, right-hand similar.

1. To install, reverse the removal procedure.

2. Refer to: Brake System Bleeding (206-00 Brake System - General Information, General Procedures).

Published: 11-May-2011
Rear Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake
Disc Vehicles With: High Performance Brakes
Removal and Installation

Removal


CAUTION: Brake discs must be renewed in pairs.


NOTE: Removal steps in this procedure may contain installation details.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Brake Pads - Vehicles With: High Performance Brakes (206-04B Rear Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol,
Removal and Installation).

3.

4.
Installation



Torque: 103 Nm
























Remove the 2 clips.
Clean the components mating faces.
1.Toinstall,reversetheremovalprocedure.

8. WARNING: If the brake caliper piston seal is damaged a
new brake caliper must be installed.


CAUTION: Do not allow the brake caliper to hang on
the brake hose.


NOTE: Left-hand shown, right-hand similar.

Torque: 28 Nm













9. NOTE: Left-hand shown, right-hand similar.