2010 JAGUAR XFR Module

Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Audio Amplifier Module (AAM)
Description and Operation

Audio Amplifier Module (AAM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:


If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty
Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new
module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Audio Amplifier Module (AAM). For
additional diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.
For additional information, refer to: Information and Entertainment System (415-00 Information and Entertainment System - General Information, Diagnosis and Testing).

DTC Description Possible Causes Action B1A01-11
Speaker #1 - Circuit
short to ground
Front left tweeter or
mid-range speaker
circuit - Short to
ground
Refer to electrical circuit diagrams and check front left
tweeter speaker circuit for short to ground B1A01-12
Speaker #1 - Circuit
short to battery
Front left tweeter or
mid-range speaker
circuit - Short to
power
Refer to electrical circuit diagrams and check front left
tweeter speaker circuit for short to power B1A01-13
Speaker #1 - Circuit
open
Front left tweeter or
mid-range speaker
circuit - Open circuit
Refer to electrical circuit diagrams and check front left
tweeter speaker circuit for open circuit B1A01-1A
Speaker #1 - Circuit
resistance below
threshold
Front left tweeter or
mid-range speaker
circuit - Resistance
below threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system www.JagDocs.com

DTC Description Possible Causes Action B1A01-49
Speaker #1 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A02-11
Speaker #2 - Circuit
short to ground
Front right tweeter or
mid-range speaker
circuit - Short to
ground
Refer to electrical circuit diagrams and check front right
tweeter speaker circuit for short to ground B1A02-12
Speaker #2 - Circuit
short to battery
Front right tweeter or
mid-range speaker
circuit - Short to
power
Refer to electrical circuit diagrams and check front right
tweeter speaker circuit for short to power B1A02-13
Speaker #2 - Circuit
open
Front right tweeter or
mid-range speaker
circuit - Open circuit
Refer to electrical circuit diagrams and check front right
tweeter speaker circuit for open circuit B1A02-1A
Speaker #2 - Circuit
resistance below
threshold
Front right tweeter or
mid-range speaker
circuit - Resistance
below threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A02-49
Speaker #2 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A03-11
Speaker #3 - Circuit
short to ground
Front left woofer
speaker circuit - Short
to ground
Refer to electrical circuit diagrams and check front left
woofer speaker circuit for short to ground B1A03-12
Speaker #3 - Circuit
short to battery
Front left woofer
speaker circuit - Short
to power
Refer to electrical circuit diagrams and check front left
woofer speaker circuit for short to power B1A03-13
Speaker #3 - Circuit
open
Front left woofer
speaker circuit - Open
circuit
Refer to electrical circuit diagrams and check front left
woofer speaker circuit for open circuit B1A03-1A Speaker #3 - Circuit
Front left woofer
Carry out any pinpoint tests associated with this DTC resistance below threshold speaker circuit - using the manufacturer approved diagnostic system Resistance below threshold B1A03-49
Speaker #3 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A04-11
Speaker #4 - Circuit
short to ground
Front right woofer
speaker circuit - Short
to ground
Refer to electrical circuit diagrams and check front right
woofer speaker circuit for short to ground B1A04-12
Speaker #4 - Circuit
short to battery
Front right woofer
speaker circuit - Short
to power
Refer to electrical circuit diagrams and check front right
woofer speaker circuit for short to power B1A04-13
Speaker #4 - Circuit
open
Front right woofer
speaker circuit - Open
circuit
Refer to electrical circuit diagrams and check front right
woofer speaker circuit for open circuit

DTC Description Possible Causes Action B1A04-1A
Speaker #4 - Circuit
resistance below
threshold
Front right woofer
speaker circuit -
Resistance below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A04-49
Speaker #4 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A05-11
Speaker #5 - Circuit
short to ground
Rear left speaker
circuit - Short to
ground
Refer to electrical circuit diagrams and check rear left
speaker circuit for short to ground B1A05-12
Speaker #5 - Circuit
short to battery
Rear left speaker
circuit - Short to
power
Refer to electrical circuit diagrams and check rear left
speaker circuit for short to power B1A05-13
Speaker #5 - Circuit
open
Rear left speaker
circuit - Open circuit
Refer to electrical circuit diagrams and check rear left
speaker circuit for open circuit B1A05-1A
Speaker #5 - Circuit
resistance below
threshold
Rear left speaker
circuit - Resistance
below threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A05-49
Speaker #5 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A06-11
Speaker #6 - Circuit
short to ground
Rear right speaker
circuit - Short to
ground
Refer to electrical circuit diagrams and check rear right
speaker circuit for short to ground B1A06-12
Speaker #6 - Circuit
short to battery
Rear right speaker
circuit - Short to
power
Refer to electrical circuit diagrams and check rear right
speaker circuit for short to power B1A06-13
Speaker #6 - Circuit
open
Rear right speaker
circuit - Open circuit
Refer to electrical circuit diagrams and check rear right
speaker circuit for open circuit B1A06-1A
Speaker #6 - Circuit
resistance below
threshold
Rear right speaker
circuit - Resistance
below threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A06-49
Speaker #6 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A07-11
Speaker #7 - Circuit
short to ground
Rear left surround
speaker circuit - Short
to ground
Refer to electrical circuit diagrams and check rear left
surround speaker circuit for short to ground B1A07-12
Speaker #7 - Circuit
short to battery
Rear left surround
speaker circuit - Short
to power
Refer to electrical circuit diagrams and check rear left
surround speaker circuit for short to power B1A07-13
Speaker #7 - Circuit
open
Rear left surround
speaker circuit - Open
circuit
Refer to electrical circuit diagrams and check rear left
surround speaker circuit for open circuit

DTC Description Possible Causes Action B1A07-1A
Speaker #7 - Circuit
resistance below
threshold
Rear left surround
speaker circuit -
Resistance below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A07-49
Speaker #7 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A08-11
Speaker #8 - Circuit
short to ground
Rear right surround
speaker circuit - Short
to ground
Refer to electrical circuit diagrams and check rear right
surround speaker circuit for short to ground B1A08-12
Speaker #8 - Circuit
short to battery
Rear right surround
speaker circuit - Short
to power
Refer to electrical circuit diagrams and check rear right
surround speaker circuit for short to power B1A08-13
Speaker #8 - Circuit
open
Rear right surround
speaker circuit - Open
circuit
Refer to electrical circuit diagrams and check rear right
surround speaker circuit for open circuit B1A08-1A
Speaker #8 - Circuit
resistance below
threshold
Rear right surround
speaker circuit -
Resistance below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A08-49
Speaker #8 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A09-11
Speaker #9 - Circuit
short to ground
Center speaker circuit
- Short to ground
Refer to electrical circuit diagrams and check center
speaker circuit for short to ground B1A09-12
Speaker #9 - Circuit
short to battery
Center speaker circuit
- Short to power
Refer to electrical circuit diagrams and check center
speaker circuit for short to power B1A09-13
Speaker #9 - Circuit
open
Center speaker circuit
- Open circuit
Refer to electrical circuit diagrams and check center
speaker circuit for open circuit B1A09-1A
Speaker #9 - Circuit
resistance below
threshold
Center speaker circuit
- Resistance below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A09-49
Speaker #9 - Internal
electronic failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A10-11
Speaker #10 - Circuit
short to ground
Left subwoofer
speaker circuit - Short
to ground
Refer to electrical circuit diagrams and check left
subwoofer speaker circuit for short to ground B1A10-12
Speaker #10 - Circuit
short to battery
Left subwoofer
speaker circuit - Short
to power
Refer to electrical circuit diagrams and check left
subwoofer speaker circuit for short to power B1A10-13
Speaker #10 - Circuit
open
Left subwoofer
speaker circuit - Open
circuit
Refer to electrical circuit diagrams and check left
subwoofer speaker circuit for open circuit

DTC Description Possible Causes Action B1A10-1A
Speaker #10 - Circuit
resistance below
threshold
Left subwoofer
speaker circuit -
Resistance below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A10-49
Speaker #10 -
Internal electronic
failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A11-11
Speaker #11 - Circuit
short to ground
Right subwoofer
speaker circuit - Short
to ground
Refer to electrical circuit diagrams and check right
subwoofer speaker circuit for short to ground B1A11-12
Speaker #11 - Circuit
short to battery
Right subwoofer
speaker circuit - Short
to power
Refer to electrical circuit diagrams and check right
subwoofer speaker circuit for short to power B1A11-13
Speaker #11 - Circuit
open
Right subwoofer
speaker circuit - Open
circuit
Refer to electrical circuit diagrams and check right
subwoofer speaker circuit for open circuit B1A11-1A
Speaker #11 - Circuit
resistance below
threshold
Right subwoofer
speaker circuit -
Resistance below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A11-49
Speaker #11 -
Internal electronic
failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index U2003-98
Fibre Optic
Communication Bus -
Component or system
over temperature
Component or system
over temperature
Clear DTC and allow system to cool, monitor for
re-occurrence of DTC U3000-05
Control module -
System programming
failures
Software
incompatibility
The version of the
Local Configuration
file does not match
that expected
Re-configure the audio amplifier as an existing control
module, using the manufacturer approved diagnostic
system U3000-42
Control module -
General memory
failure
General memory
failure
Re-configure the audio amplifier as an existing control
module, using the manufacturer approved diagnostic
system. Clear DTC, cycle ignition and read DTCs. If DTC
returns, suspect audio amplifier module and install a
new module. Refer to the new module/component
installation note at the top of the DTC Index U3000-44
Control module - Data
memory failure
Data memory failure
Re-configure the audio amplifier as an existing control
module, using the manufacturer approved diagnostic
system. Clear DTC, cycle ignition and read DTCs. If DTC
returns, suspect audio amplifier module and install a
new module. Refer to the new module/component
installation note at the top of the DTC Index U3000-55
Control Module - Not
configured
Incorrect car
configuration data
received
Check/up-date Car Configuration File using manufacturer
approved diagnostic system U3000-87
Control Module -
Missing message
Missing message
Check CJB for DTCs and refer to DTC Index. Check
information and entertainment module for Car
Configuration File and MOST network DTCs and refer to
relevant DTC Index. Carry out MOST/CAN network tests
using the manufacturer approved diagnostic system

Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Blind Spot Monitoring System Module (SODL/SODR)
Description and Operation

Blind Spot Monitoring System Module (SODL/SODR)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault and may also cause additional faults in the vehicle being checked and/or the donor vehicle.
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer approved diagnostic system).


When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places,
and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the DMM leads into
account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


If DTCs are recorded and, after performing the pinpoint tests a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Where an 'on demand self-test' is referred to, this can be accessed via the 'DTC Monitor' tab on the manufacturers
approved diagnostic system.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Blind Spot Monitoring System Module, for
additional Diagnosis and Testing information refer to the relevant Diagnosis and Testing Section.
For additional information, refer to: Warning Devices (413-09 Warning Devices, Diagnosis and Testing).

DTC Description Possible Causes Action B11C9-11
Driver Display Status
LED - Circuit short to
ground
Circuit short to ground
Refer to the electrical circuit diagrams and check
driver display status LED circuit for short to
ground B11C9-15
Driver Display Status
LED - Circuit short to
battery or open
Circuit short to power or
open circuit
Refer to the electrical circuit diagrams and check
driver display status LED circuit for short to
ground B11D6-11
Driver Display Alert LED -
Circuit short to ground
Circuit short to ground
Refer to the electrical circuit diagrams and check
driver display status LED circuit for short to
ground B11D6-15
Driver Display Alert LED -
Circuit short to battery
or open
Circuit short to power or
open circuit
Refer to the electrical circuit diagrams and check
driver display status LED circuit for short to
ground U0010-00
Medium Speed CAN
Communication Bus - No
sub type information
No sub type information
Refer to the electrical circuit diagrams and check
the power and ground connections to the module.
Using the manufacturer approved diagnostic
system, complete a CAN network integrity test.
Refer to the electrical circuit diagrams and check

DTC Description Possible Causes Action the CAN network U0140-00
Lost Communication
With Body Control
Module - No sub type
information
No sub type information
Refer to the electrical circuit diagrams and check
the power and ground connections to the module.
Using the manufacturer approved diagnostic
system, complete a CAN network integrity test.
Refer to the electrical circuit diagrams and check
the CAN network between the Central Junction
Box and Blind Spot Monitoring System Module U0155-00
Lost Communication
With Instrument Panel
Cluster (IPC) Control
Module - No sub type
information
No sub type information
Refer to the electrical circuit diagrams and check
the power and ground connections to the module.
Using the manufacturer approved diagnostic
system, complete a CAN network integrity test.
Refer to the electrical circuit diagrams and check
the CAN network between the Instrument Cluster
and Blind Spot Monitoring System Module U0232-00
Lost Communication
With Blind Spot
Monitoring System
Module - Left - No sub
type information
CAN bus circuit fault
Harness fault between left
side mirror and left side
module
Refer to the electrical circuit diagrams and check
the power and ground connections to the module.
Using the manufacturer approved diagnostic
system, complete a CAN network integrity test.
Refer to the electrical circuit diagrams and check
the CAN network between the left Blind Spot
Monitoring System Module and the right Blind
Spot Monitoring System Module
Refer to the electrical circuit diagrams and check
the left side harness between the left side mirror
and left hand module U0233-00
Lost Communication
With Blind Spot
Monitoring System
Module - Right - No sub
type information
CAN bus circuit fault
Harness fault between
right side mirror and right
side module
Refer to the electrical circuit diagrams and check
the power and ground connections to the module.
Using the manufacturer approved diagnostic
system, complete a CAN network integrity test.
Refer to the electrical circuit diagrams and check
the CAN network between the left Blind Spot
Monitoring System Module and the right Blind
Spot Monitoring System Module
Refer to the electrical circuit diagrams and check
the right side harness between the right side
mirror and right hand module U0300-00
Internal Control Module
Software Incompatibility
- No sub type
information
No sub type information
Check Central Junction Box for related DTCs and
refer to the relevant DTC Index. Check Restraints
Control Module for related DTCs and refer to DTC
Index. Check correct components are installed
and that the latest software version is installed U0415-68
Invalid Data Received
From Anti-Lock Brake
System (ABS) Control
Module - event
information
Event information
Using the manufacturer approved diagnostic
system check the central junction box and the
anti-lock brake system (ABS) control module for
related DTCs and refer to the relevant DTC Index U0422-68
Invalid Data Received
From Body Control
Module - Event
information
Event information
Check the Central Junction Box for related DTCs
and refer to the relevant DTC index U2100-00
Initial Configuration Not
Complete - No sub type
information
Car Configuration File
information not received
completely
Check/amend Car Configuration File using
manufacturer approved diagnostic system U2101-00
Control Module
Configuration
Incompatible - No sub
type information
Car Configuration File
information incompatible
to Control module
Check/amend Car Configuration File using
manufacturer approved diagnostic system U3000-44
Control Module - Data
memory failure
Control module data
memory failure
Refer to the electrical circuit diagrams and check
the power and ground circuits to the component.
Refer to the warranty policy and procedures
manual if a module is suspect

DTC Description Possible Causes Action U3000-47
Control Module -
Watchdog/safety
microcontroller failure
Control module internal
watchdog/safety
MicroController failure
Refer to the electrical circuit diagrams and check
the power and ground circuits to the component.
Refer to the warranty policy and procedures
manual if a module is suspect U3000-49
Control Module - Internal
electronic failure
Control module internal
electronic failure (internal
error)
Clear DTC, cycle ignition and retest. If fault
persists, refer to the electrical circuit diagrams
and check the power and ground circuits to the
component. Repair as required, clear DTC and
retest
If fault persists, check and install a new
blindspot monitoring control module as required.
Refer to the warranty policy and procedures
manual if a module is suspect U3003-62
Battery Voltage - Signal
compare failure
Mis-match in battery
voltage, between Central
Junction Box and Blind
Spot Monitoring System
module, of 2 volts or more
Check the module connector for security and
integrity. Refer to the electrical circuit diagrams
and check the Control module supply voltage.
Check vehicle battery voltage and state of
charge. Check the power signal line to the
module