2010 JAGUAR XFR 303

Published: 11-May-2011
Engine - V8 S/C 5.0L Petrol - Engine Oil Vacuum Draining and Filling
General Procedures

Special Tool(s)


303-1484
Vacuum Pump, Oil Drain

303-1484-01
Adapter for 303-1484
Draining

WARNING: The spilling of hot engine oil is unavoidable during this procedure, care must be taken to prevent scalding.


CAUTION: Correct installation of the oil filler cap can be obtained by tightening the cap until hard stop.

NOTES:


Make sure that the vehicle is parked on level ground.


Clean the components general area prior to dismantling.

1.
Start the engine and allow to run for 10 minutes, stop the
engine.


2. CAUTION: Allow 10 minutes from turning the engine off
before starting oil extraction.











3. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

8. NOTE: Discard the O-ring seals.
















Filling

1. NOTE: Install new O-ring seals.
Lubricate the oil filter element O-ring seal with clean
engine oil.













2. CAUTION: Tighten the component finger tight first.
Torque: 25 Nm











3. CAUTION: Make sure that the vehicle is left for 5 minutes from
filling with oil and that the engine oil level is reading at least minimum
(by following Steps 7-11), before starting the engine.

Fill the engine with oil - for filling values on vehicles without
supercharger:

Refer to: Specifications (303-01C Engine - V8 5.0L Petrol, Specifications).
Fill the engine with oil - for filling values on vehicles with
supercharger:

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol,

Engine - V8 S/C 5.0L Petrol - Fuel Pump Camshaft Timing Check
General Procedures

Special Tool(s)

303-1447
Timing Tool
JLR-303-1621
Alignment Tool, Fuel Pump Camshaft Timing
Check Published: 16-Dec-2013

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.

Raise and support the vehicle.

3. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

4. CAUTION: Be prepared to collect escaping oil.
NOTES:

Discard the sealing washer.


Collect the engine oil in a clean container.








5.

6. CAUTIONS:


Only rotate the crankshaft clockwise.


Make sure that the crankshaft is fully locked.

Install the Special Tool(s): 303-1447








7. Using a suitable marker, mark the position of the crankshaft pulley as
illustrated.

















8.
9. NOTE: Discard the seal. www.JagDocs.com

10. Remove the Special Tool(s): 303-1447


















11.


















If required,
carefully
adjust the
crankshaft
position to
allow correct
installation
of the
special tool.

Install the
Special
Tool(s):
JLR-303-1621
















12.
CAUTION: Do not use excessive force when adjusting the crankshaft
position.


NOTE: If the crankshaft timing tool cannot be installed, adjustment of
the fuel pump camshaft timing will be required.

If required, carefully adjust the crankshaft position to allow correct
installation of the special tool.

Install the Special Tool(s): 303-1447 If the crankshaft timing tool cannot be installed, adjustment of the
fuel pump camshaft timing will be required.

Refer to: Fuel Pump Camshaft Timing Adjustment (303-01C Engine - V8 5.0L Petrol, General Procedures).

13.
14.
15.
16. Remove the Special Tool(s): JLR-303-1621

























NOTE: Install a new seal.

Torque: 12 Nm
































Remove the Special Tool(s): 303-1447

17.
18. Torque: 10 Nm


















NOTE: Install a new sealing washer.

Torque: 24 Nm









19.




20. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).



CAUTION: Make sure that the vehicle is left for 5 minutes from filling with oil and
that the engine oil level is reading at least minimum (by following Steps 23-27), before
starting the engine.

Fill the engine with oil - for filling values on vehicles without supercharger:

Refer to: Specifications (303-01C Engine - V8 5.0L Petrol, Specifications). Fill the engine with oil - for filling values on vehicles with supercharger:

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol, Specifications). Clean any residual engine oil from the oil filler cap area.


21.
oil. CAUTION: Make sure that the vehicle has been left for 5 minutes from filling with

Follow the Steps 23-27 before starting the engine.

22.
Start the engine and allow to run for 10 minutes, stop the engine.
Check for leaks.

23. CAUTIONS:


Make sure that the selector lever and the gearshift mechanism are in the park (P)
position.


Make sure that the hood is open.
Turn the ignition on.

Published: 21-Dec-2011
Engine - V8 S/C 5.0L Petrol - Fuel Pump Camshaft Timing Adjustment
General Procedures

Special Tool(s)


303-1447
Timing Tool

JLR-303-1613
Alignment Tool, Fuel Pump Camshaft Timing
Adjustment

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

3. Refer to: Fuel Pump Camshaft Timing Check (303-01D Engine - V8 S/C 5.0L Petrol, General Procedures).

4. Refer to: Lower Timing Cover (303-01C Engine - V8 5.0L Petrol, Removal and Installation).
Refer to: Lower Timing Cover (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).