2010 JAGUAR XFR diagram

DTC Description Possible Causes Action B1D19-93
Compact Disc Unit -
No operation
No operation
Suspect the integrated audio module, check and
install a new module as required, refer to the new
module/component installation note at the top of
the DTC Index B1A01-11
Speaker #1 - Circuit
short to ground
Front driver speaker circuits
- short to ground
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test front driver speaker circuits for short to ground B1A01-12
Speaker #1 - Circuit
short to battery
Front driver speaker circuits
- short to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test front driver speaker circuits for short to power B1A01-1A
Speaker #1 - Circuit
resistance below
threshold
Front driver speaker circuits
- resistance below
threshold
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system B1A01-1B
Speaker #1 - Circuit
resistance above
threshold
Front driver speaker circuits
- resistance above
threshold
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system B1A01-1C
Speaker #1 - Circuit
voltage out of range
Front driver speaker circuits
- voltage out of range.
Power IC failure internal to
the integrated audio
Suspect the integrated audio module. Check and
install a new module as required, refer to the new
module/component installation note at the top of
the DTC Index B1A02-11
Speaker #2 - Circuit
short to ground
Front passenger speaker
circuits - short to ground
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test front passenger speaker circuits for short to
ground B1A02-12
Speaker #2 - Circuit
short to battery
Front passenger speaker
circuits - short to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test front passenger speaker circuits for short to
power B1A02-1A
Speaker #2 - Circuit
resistance below
threshold
Front passenger speaker
circuits - resistance below
threshold
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system B1A02-1B
Speaker #2 - Circuit
resistance above
threshold
Front passenger speaker
circuits - resistance above
threshold
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system B1A02-1C
Speaker #2 - Circuit
voltage out of range
Front passenger speaker
circuits - voltage out of
range. Power IC failure
internal to the integrated
audio
Suspect the integrated audio module. Check and
install a new module as required, refer to the new
module/component installation note at the top of
the DTC Index B1A03-11
Speaker #3 - Circuit
short to ground
Rear left speaker circuits -
short to ground
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test rear left speaker circuits for short to ground B1A03-12
Speaker #3 - Circuit
short to battery
Rear left speaker circuits -
short to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test rear left speaker circuits for short to power

DTC Description Possible Causes Action B1A03-1A
Speaker #3 - Circuit
resistance below
threshold
Rear left speaker circuits -
resistance below threshold
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system B1A03-1B
Speaker #3 - Circuit
resistance above
threshold
Rear left speaker circuits -
resistance above threshold
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system B1A03-1C
Speaker #3 - Circuit
voltage out of range
Rear left speaker circuits -
voltage out of range. Power
IC failure internal to the
integrated audio
Suspect the integrated audio module. Check and
install a new module as required, refer to the new
module/component installation note at the top of
the DTC Index B1A04-11
Speaker #4 - Circuit
short to ground
Rear right speaker circuits -
short to ground
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test rear right speaker circuits for short to ground B1A04-12
Speaker #4 - Circuit
short to battery
Rear right speaker circuits -
short to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test rear right speaker circuits for short to power B1A04-1A
Speaker #4 - Circuit
resistance below
threshold
Rear right speaker circuits -
resistance below threshold
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system B1A04-13
Speaker #4 - Circuit
open
Rear right speaker circuits -
resistance above threshold
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system B1A04-1C
Speaker #4 - Circuit
voltage out of range
Rear right speaker circuits -
voltage out of range. Power
IC failure internal to the
integrated audio
Suspect the integrated audio module. Check and
install a new module as required, refer to the new
module/component installation note at the top of
the DTC Index B1A56-13
Antenna - Circuit
open
Antenna circuit - open
circuit
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check antenna circuit for open circuit B1D78-11
Auxiliary Input -
Circuit short to
ground
Auxiliary input circuit -
short to ground
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test Auxiliary input circuits for short to ground B1D78-12
Auxiliary Input -
Circuit short to
battery
Auxiliary input circuit -
short to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test Auxiliary input circuits for short to power B1D78-13
Auxiliary Input -
Circuit open
Auxiliary input circuit - high
resistance
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test Auxiliary input circuits for high resistance B1D79-11
Microphone Input -
Circuit short to
ground
Microphone input circuit -
short to ground
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test microphone input circuits for short to ground B1D79-12
Microphone Input -
Circuit short to
battery
Microphone input circuit -
short to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test microphone input circuits for short to power

DTC Description Possible Causes Action B1D79-13
Microphone Input -
Circuit open
Microphone input circuit -
high resistance
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test microphone input circuits for high resistance B1134-11
Phone Input - Circuit
short to ground
Phone input circuit - short
to ground
Refer to the electrical circuit diagrams and test
phone input circuits for short to ground B1134-12
Phone Input - Circuit
short to battery
Phone input circuit - short
to power
Refer to the electrical circuit diagrams and test
phone input circuits for short to power B1134-13
Phone Input - Circuit
open
Phone input circuit - high
resistance
Refer to the electrical circuit diagrams and test
phone input circuits for high resistance U2100-00
Initial Configuration
Not Complete - No
sub type information
Car configuration data not
received
Check RJB for related DTCs and refer to the relevant
DTC Index U2101-00
Control Module
Configuration
Incompatible - No sub
type information
Incorrect car configuration
data received
Check RJB for related DTCs and refer to the relevant
DTC Index. Check/amend Car Configuration File
using the manufacturer approved diagnostic system U3000-49
Control Module -
Internal electronic
failure
Internal electronic failure
Suspect the integrated audio module, install a new
module as required, refer to the new module
installation note at the top of the DTC Index U3000-55
Control Module - Not
configured
Incorrect car configuration
data received
Re-configure the RJB using the manufacturer
approved diagnostic system. Clear DTC and re-test.
If the DTC remains suspect the integrated audio
module, refer to the new module installation note
at the top of the DTC Index U3000-87
Control Module -
Missing message
Missing message
Re-configure the RJB using the manufacturer
approved diagnostic system. Check integrated audio
module for DTCs and refer to the DTC Index. Check
CAN network integrity using the manufacturer
approved diagnostic system U3000-98
Control Module -
Component or system
over temperature
Component or system over
temperature
Check for additional DTCs and refer to DTC Index.
Clear DTC and re-test/monitor condition U3003-62
Battery Voltage -
Signal compare failure
Mis-match in battery
voltage, of 2 volts or more,
between integrated audio
module and RJB
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system

Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Occupant Classification System (OCS)
Description and Operation

Occupant Classification System (OCS)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


It is advisable not to use a cellular phone or to have a cellular phone in close proximity when working on the restraints
control module or associated systems


Given the legal implications of a restraints system failure, harness repairs to Air Bag module circuits are not acceptable.
Where the text refers to "REPAIR the circuit", this will normally mean the replacement of a harness.


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals


Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the
manufacturers approved diagnostic system


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the occupant classification system, for
additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) (501-20
Supplemental Restraint System, Diagnosis and Testing).

DTC Description Possible Causes Action B1193-53
Crash Event
Storage Full and
Locked -
Deactivated
Crash event occurred
Clear diagnostic trouble code and re-test B1A54-01
Occupant Belt Tension Sensor -
General Electrical
Failure
General electrical failure
Clear diagnostic trouble code and re-test. If the problem
persists, check and install a new safety belt tension
sensor as required. Refer to the warranty policy and
procedures manual, or determine if any prior approval
programme is in operation, prior to the installation of a
new module/component B1A54-02
Occupant Belt Tension Sensor -
General signal
failure
General signal failure
Refer to the electrical circuit diagrams and check safety
belt tension and mat pressure sensor circuits for short to
each other

DTC Description Possible Causes Action B1A54-11
Occupant Belt Tension Sensor -
Circuit short to
ground
Safety belt tension
sensor voltage reference
or signal circuit - short
to ground
Refer to the electrical circuit diagrams and check safety
belt tension sensor voltage reference and signal circuits
for short to ground B1A54-12
Occupant Belt Tension Sensor -
Circuit short to
battery
Safety belt tension
sensor voltage reference
or signal circuit - short
to power
Refer to the electrical circuit diagrams and check safety
belt tension sensor voltage reference and signal circuits
for short to power B1A54-13
Occupant Belt Tension Sensor -
Circuit open
Safety belt tension
sensor voltage reference
or signal circuit - open
circuit
Refer to the electrical circuit diagrams and check safety
belt tension sensor voltage reference and signal circuits
for open circuit B1A62-02
Pressure Sensor -
General signal
failure
General signal failure
Refer to the electrical circuit diagrams and check safety
belt tension and mat pressure sensor circuits for short to
each other B1A62-11
Pressure Sensor -
Circuit short to
ground
Mat pressure sensor
voltage reference or
signal circuits - short to
ground
Refer to the electrical circuit diagrams and check mat
pressure sensor voltage reference and signal circuits for
short to ground B1A62-12
Pressure Sensor -
Circuit short to
battery
Mat pressure sensor
voltage reference,
ground or signal circuits
- short to power
Refer to the electrical circuit diagrams and check mat
pressure sensor voltage reference, ground and signal
circuits for short to power B1A62-13
Pressure Sensor -
Circuit open
Mat pressure sensor
voltage reference or
signal circuit - open
circuit
Refer to the electrical circuit diagrams and check mat
pressure sensor voltage reference and signal circuits for
open circuit B1A62-7B
Pressure Sensor -
Low fluid level
Low fluid level - bladder
damaged
Check and install new bladder as required. Refer to the
warranty policy and procedures manual, or determine if
any prior approval programme is in operation, prior to the
installation of a new module/component U0001-88
High Speed CAN
Communication
Bus - Bus off
Bus off
Refer to the electrical circuit diagrams and check CAN
network for short, open circuit. Carry out the CAN
network integrity test using the manufacturer approved
diagnostic system U0151-00
Lost
Communication
With Restraints
Control Module -
No sub type
information
Restraints control
module missing
message
Refer to the electrical circuit diagrams and check power
and ground supplies to restraints control module. Carry
out CAN network integrity test using the manufacturer
approved diagnostic system U0300-00
Internal Control
Module Software
Incompatibility -
No sub type
information
Master car configuration
file ID does not
correspond
Check correct occupancy seat module is installed for
vehicle specification. Check rear junction box for related
diagnostic trouble codes and refer to relevant diagnostic
trouble code index U2016-51
Control Module
Main Software -
Not programmed
Main software not
programmed
Check and install a new occupancy seat module as
required. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component U201A-51
Control Module
Main Calibration
Data - Not
programmed
Main calibration data not
programmed
Check and install a new occupancy seat module as
required. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component

Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Parking Aid
Module (PAM)
Description and Operation

Parking Aid Control Module (PACM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals


Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the
manufacturers approved diagnostic system


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required


Physical damage to the sensor (impact damage or scratched sensor surface) must NOT be changed under warranty.

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the Parking Aid Control Module (PACM). For
additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Parking Aid (413-13 Parking Aid, Diagnosis and Testing).
DTC Description Possible Causes Action B1B36-01
Front Right Outer
Sensor - General
Electrical Failure
Wiring harness fault
Front right outer sensor
- Component internal
failure
Refer to electrical wiring diagrams and check the front
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor www.JagDocs.com

DTC Description Possible Causes Action B1B36-12
Front Right Outer
Sensor - Circuit short
to battery
Wiring harness fault
Refer to electrical wiring diagrams and check the front
bumper harness for damage. Check sensor circuit for
short circuit to power. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test B1B36-96
Front Right Outer
Sensor - Component
internal failure
Wiring harness fault
Front right outer sensor
- Component internal
failure
Refer to electrical wiring diagrams and check the front
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B38-01
Front Right Inner
Sensor - General
Electrical Failure
Wiring harness fault
Front right inner sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the front
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B38-12
Front Right Inner
Sensor - Circuit short
to battery
Wiring harness fault
Refer to electrical wiring diagrams and check the front
bumper harness for damage. Check sensor circuit for
short circuit to power. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test B1B38-96
Front Right Inner
Sensor - Component
internal failure
Wiring harness fault
Front right inner sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the front
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor

DTC Description Possible Causes Action B1B40-01
Front Left Outer
Sensor - General
electrical failure
Wiring harness fault
Front left outer sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the front
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B40-12
Front Left Outer
Sensor - Circuit short
to battery
Wiring harness fault
Refer to electrical wiring diagrams and check the front
bumper harness for damage. Check sensor circuit for
short circuit to power. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test B1B40-96
Front Left Outer
Sensor - Component
internal failure
Wiring harness fault
Front left outer sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the front
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B42-01 Front Left Inner Sensor
- General electrical
failure
Wiring harness fault
Front left inner sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the front
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B42-12 Front Left Inner Sensor
- Circuit short to
battery
Wiring harness fault
Refer to electrical wiring diagrams and check the front
bumper harness for damage. Check sensor circuit for
short circuit to power. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test