2010 INFINITI QX56 diagram

AV
AUDIO SYSTEMAV-9
< FUNCTION DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
FUNCTION DIAGNOSIS
AUDIO SYSTEM
System DiagramINFOID:0000000005146222
System DescriptionINFOID:0000000005146223
AUDIO SYSTEM
AWNIA1867GB
Revision: April 20092010 QX56

AV
NAVIGATION SYSTEMAV-13
< FUNCTION DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
NAVIGATION SYSTEM
System DiagramINFOID:0000000005146226
System DescriptionINFOID:0000000005146227
NOTE:
Refer to NAVI System Owner's Manual for system operation.
The navigation system periodically calculates the vehicl e's current position according to the following three
signals: Travel distance of the vehicle as determined by the vehicle speed sensor, turning angle of the vehicle
as determined by the gyroscope (angular velocity sensor), and the direction of vehicle travel as determined by
the GPS antenna (GPS information).
The current position of the vehicle is then identified by comparing the calculated vehicle position with map data
read from the map data, which is stored in the har d disk drive (HDD)(map-matching), and indicated on the
screen with a current-location mark.
By comparing the vehicle position detection results found by the
GPS and by map-matching, more accurate vehicle position data can
be used.
The current vehicle position will be calculated by detecting the dis-
tance the vehicle moved from the previous calculation point and its
direction.
TRAVEL DISTANCE
Travel distance calculations are based on the vehicle speed input signal. Therefore, the calculation may
become incorrect as the tires wear down. To prevent this, an automatic distance fine adjustment function has
been adopted.
TRAVEL DIRECTION
Change in the travel direction of the vehicle is calculated by a gyroscope (angular velocity sensor) and a GPS
antenna (GPS information). As the gyroscope and GP S antenna have both merit and demerit, input signals
from them are prioritized in each situation. However, this order of priority may change in accordance with more
detailed travel conditions so that the travel direction is detected more accurately.
ALNIA0424GB
SEL684V
Revision: April 20092010 QX56

AV-18
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
REAR VIEW MONITOR SYSTEM
REAR VIEW MONITOR SYSTEM
System DiagramINFOID:0000000005146230
System DescriptionINFOID:0000000005146231
When the selector is in the R position, the display shows
a view to the rear of the vehicle. Lines which indicate
the vehicle clearance and distances are also displayed.
AV COMMUNICATION LINE
The rear view camera control unit is connected to the AV control unit using an AV communication line. This
line is used to transmit and receive data.
AWNIA1549GB
Revision: April 20092010 QX56

AV
DVD PLAYERAV-21
< FUNCTION DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
DVD PLAYER
System DiagramINFOID:0000000005146234
System DescriptionINFOID:0000000005146235
The DVD entertainment system consists of the following components
• AV control unit
• DVD player
• Video monitor
• A/C and AV switch assembly
• Steering wheel audio control switches
• Rear audio remote control unit
• BOSE speaker amp.
• Front tweeters
• Front door speakers
• Center speaker
• Rear door tweeters
• Rear door speakers
• Back door speakers
• Subwoofer
When the DVD entertainment system is on, video signals are sent from the DVD player to the video monitor.
Audio signals are sent to the AV control unit. Audio signals can be directed through wireless infrared head-
phones or through the BOSE speaker amp. to the vehicle speakers. Refer to the Owner’s Manual for complete
DVD entertainment system operating instructions.
AWNIA1550GB
Revision: April 20092010 QX56

AV-24
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
HANDS-FREE PHONE SYSTEM
HANDS-FREE PHONE SYSTEM
System DiagramINFOID:0000000005146238
System DescriptionINFOID:0000000005146239
Refer to the Owner's Manual for Bluetoot
h telephone system operating instructions.
NOTE:
Cellular telephones must have their wireless connection set up (paired) before using the Bluetooth telephone
system.
Bluetooth telephone system allows users who have a Bluetooth equipped cellular telephone to make a wire-
less connection between their cellular telephone and the AV control unit. Hands-free cellular telephone calls
can be sent and received. Personal memos can be created using the Nissan Voice Recognition system. Some
Bluetooth cellular telephones may not be recognized by t he AV control unit. When a cellular telephone or the
AV control unit is replaced, the telephone must be pair ed with the AV control unit. Different cellular telephones
may have different pairing procedures. Refer to the cellular telephone operating manual and the vehicle
Owner’s Manual for more information.
AV CONTROL UNIT
When the ignition switch is turned to ACC or ON, the AV control unit will power up. During power up, the Blue-
tooth feature is initialized and performs various self checks. Initialization may take up to 10 seconds. If a
phone is present in the vehicle and paired with the AV control unit, Nissan Voice Recognition will then become
active. Bluetooth telephone functions can be turned off using the Nissan Voice Recognition system.
STEERING WHEEL AUDIO CONTROL SWITCHES
When buttons on the steering wheel audio control switch are pushed, the resistance in steering wheel audio
control switch circuit changes depending on which button is pushed. The AV control unit uses this signal to
perform various functions while navigati ng through the voice recognition system.
The following functions can be performed using the steering wheel audio control switch:
• Initiate Self Diagnosis of the Bluetooth telephone system
• Start a voice recognition session
• Answer and end telephone calls
• Adjust the volume of calls
• Record memos
MICROPHONE
The microphone is located in the roof console assembly . The microphone sends a signal to the AV control unit.
The microphone can be actively tested during self-diagnosis.
AWNIA0131GB
Revision: April 20092010 QX56

AV-60
< COMPONENT DIAGNOSIS >[AUDIO SYSTEM]
U1243 DISPLAY UNIT
U1243 DISPLAY UNIT
DescriptionINFOID:0000000005146286
DTC LogicINFOID:0000000005146287
Diagnosis ProcedureINFOID:0000000005146288
Regarding Wiring Diagram information, refer to
AV-116, "Wiring Diagram".
1.CHECK DISPLAY UNIT POWER SUPPLY AND GROUND CIRCUIT
Check display unit power supply and ground circuit. Refer to AV-69, "
DISPLAY UNIT : Diagnosis Procedure".
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair malfunctioning parts.
2.CHECK CONTINUITY CO MMUNICATION CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector M93 and AV control unit connector M43.
3. Check continuity between display unit harness connector M93 (A) terminals 11, 22 and AV control unit harness connector M43
(B) terminals 30, 31.
4. Check continuity between display unit harness connector M93 (A) terminals 11, 22 and ground.
Part name Description
DISPLAY UNIT • Display image is controlled by the serial communication from AV control unit.
• RGB image signal is input from AV control unit (RGB, RGB area and RGB syn-
chronizing). Auxiliary image signal is input from the auxiliary input jack. Cam-
era image signal is input from the camera control unit.
• Synchronize signal (HP, VP) is output to AV control unit.
• Touch panel function can be operated for each system by touching a display directly.
DTC Display contents of
CONSULT-III DTC Detection Condition
Possible causes
U1243 FRONT DISP CONN
[U1243] • Display unit power supply and ground circuit malfunc-
tion is detected.
• Malfunction is detected on communication circuit be- tween display unit and AV control unit.
• Malfunction is detected on communication signal be-
tween display unit and AV control unit. • Display unit power supply and
ground circuit.
• Communication circuit between display unit and AV control unit.
AB Continuity
Connector Terminal Connector Terminal
M93 11
M43 30
Ye s
22 31
A —Contin u it y
Connector Terminal
M93 11
Ground No
22
ALNIA0397GB
Revision: April 20092010 QX56

AV-62
< COMPONENT DIAGNOSIS >[AUDIO SYSTEM]
U1244 GPS ANTENNA
U1244 GPS ANTENNA
DescriptionINFOID:0000000005146289
DTC LogicINFOID:0000000005146290
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000005146291
Regarding Wiring Diagram information, refer to
AV-116, "Wiring Diagram".
1.GPS ANTENNA CHECK
Inspect GPS antenna and antenna feeder for damage or poor connection.
Is the GPS antenna and feeder clean and undamaged?
YES >> GO TO 2.
NO >> Repair or replace malfunctioning parts.
2.CHECK AV CONTROL UNIT VOLTAGE
1. Turn ignition switch ON.
2. Check voltage between AV control unit connector M124 terminal 116 and ground.
Is the voltage reading as specified?
YES >> Replace GPS antenna. Refer to AV-186, "Removal and
Installation".
NO >> Replace AV control unit. Refer to AV-169, "
Removal and
Installation".
Part Name Description
GPS ANTENNA GPS signal is detected and transmitted to the AV control unit.
DTC CONSULT-III display Detection condition
U1244 GPS ANTENNA CONN
[U1244]
GPS antenna connection malfunction is detected.
116 - Ground
: Approx. 5V
ALNIA0400GB
Revision: April 20092010 QX56

AV
U1250 CAMERA CONTROL UNITAV-63
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
U1250 CAMERA CONTROL UNIT
DescriptionINFOID:0000000005146292
DTC LogicINFOID:0000000005146293
Diagnosis ProcedureINFOID:0000000005146294
Regarding Wiring Diagram information, refer to AV-116, "Wiring Diagram".
1.CHECK CAMERA-CONNECTION RECOGNITION SIGNAL CIRCUIT
1. Disconnect AV control unit connector and camera control unit connector.
2. Check continuity between AV control unit harness connector M45 (A) terminal 84 and camera control unit harness connector
B73 (B) terminal 5.
3. Check continuity between AV control unit harness connector M45 (A) terminal 84 and ground.
Are the continuity results as specified?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AV CONTROL UNIT VOLTAGE
Part name Description
CAMERA CONTROL UNIT • Camera image signal is input from rear view camera, and camera image is in-
dicated on the display.
• Power (camera ON signal) is sent to rear view camera.
• Controlled by audio communication sent from AV control unit.
• AV control unit recognizes the presence of camera system with camera con- nection recognition signal.
DTC Display contents of
CONSULT-III DTC Detection Condit
ion Possible causes
U1250 CAMERA CONT. CONN
[U1250] A malfunction is detected in camera-connection recogni-
tion signal circuit. Camera-connection recognition sig-
nal circuit.
AB
Continuity
Connector Terminal Connector Terminal
M45 84 B73 5 Yes
A —Con tin uit y
Connector Terminal
M45 84Ground No
ALNIA0401GB
Revision: April 20092010 QX56