2010 INFINITI QX56 Ignition switch

INTELLIGENT KEY WARNING BUZZERDLK-95
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
INTELLIGENT KEY WARNING BUZZER
DescriptionINFOID:0000000005146963
Answers back and warns for an inappropriate operation.
Component Function CheckINFOID:0000000005146964
1.CHECK FUNCTION
With CONSULT-III
Check Intelligent Key warning buzzer "OUTSIDE BUZZER" in Active Test mode.
Is the inspection result normal?
YES >> Intelligent Key warning buzzer (engine room) is OK.
NO >> Refer to DLK-95, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146965
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK INTELLIGENT KEY WARNING BUZZER (ENGINE ROOM) POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect Intelligent Key warning buzzer (engine room) connector.
3. Check voltage between Intelligent Key warning buzzer (engine room) harness connector E25 terminal 1 and ground.
Is the inspection normal?
YES >> GO TO 2
NO >> Repair or replace Intelligent Key warning buzzer (engine room) power supply circuit.
2.CHECK INTELLIGENT KEY WARNING BUZZER (ENGINE ROOM) CIRCUIT
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit harness connector (A) M70 terminal 4 and Intelligent Key warning buzzer (engine
room) harness connector E25 terminal 3.
3. Check continuity between Intelligent Key warning buzzer (engine room) harness connector E25 terminal 3 and ground.
Is the inspection normal?
YES >> GO TO 3
NO >> Repair or replace harness between Intelligent Key warning buzzer (engine room) and Intelligent Key unit.
3.CHECK INTELLIGENT KEY WARNING BU ZZER (ENGINE ROOM) OPERATION
Check DLK-96, "
Component Inspection".
1 - Ground : Battery voltage
WIIA1195E
4 - 3: Continuity should exist.
3 - Ground : Continuity should not exist.
WIIA1196E
Revision: April 20092010 QX56

OUTSIDE KEY ANTENNADLK-97
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
OUTSIDE KEY ANTENNA
DescriptionINFOID:0000000005146967
Detects whether the Intelligent Key is in the operating range of the outside antennas.
Front outside antennas are integrated in front outside door handles (driver side, passenger side) to allow lock-
ing and unlocking of door locks when the Intelligent Key is present.
Rear bumper antenna is mounted on the rear bumper and is used to allow the back door and glass hatch
switch assembly opening of the back door when the Intelligent Key is present.
Component Function CheckINFOID:0000000005146968
1.CHECK DOOR REQUEST SWITCHES
Check that door request switches operate normally.
Is the inspection result normal?
YES >> GO TO 2
NO >> Inspect door request switches. Refer to DLK-83, "
ComponentFunctionCheck".
2.CHECK OUTSIDE KEY ANTENNAS FUNCTION
Be sure that Intelligent Key is in each outside key antenna detection range.
Does door lock/unlock when each request switch is pressed?
YES >> GO TO 3
NO >> Refer to DLK-97, "
Diagnosis Procedure".
3.CHECK REAR ANTENNA FUNCTION
Be sure that Intelligent Key is in rear bumper antenna detection range.
Be sure that back door close switch is not in the "CANCEL" position.
Does power back door open when back door switch is operated?
YES >> Outside key antennas are OK.
NO >> Refer to DLK-138, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146969
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between Intelligent Key unit connector M70 terminals 17, 19, 37 and ground with an oscillo- scope.
Is the inspection result normal?
Connector Item Te r m i n a l s
Condition Signal
(Reference value)
(+) (-)
M70 Rear
bumper
antenna
17
Ground Request
switch is
pushed
Front out-
side an-
tenna LH
19
Front out-
side an-
tenna RH 37
WIIA1198E
SIIA1910J
Revision: April 20092010 QX56

STEERING LOCK UNITDLK-99
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
STEERING LOCK UNIT
Diagnosis ProcedureINFOID:0000000005146970
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK STEERING LOCK SOLENOID POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect steering lock solenoid connector.
3. Check voltage between steering lock solenoid harness connector M15 terminal 1 and ground.
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace steering lock solenoid power supply circuit.
2.CHECK STEERING LOCK SOLENOID GROUND CIRCUIT
Check continuity between steering lock sol enoid harness connector M15 terminal 4 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace the steering lock solenoid ground cir- cuit.
3.CHECK INTELLIGENT KEY UNIT OUTPUT SIGNAL
1. Connect steering lock solenoid connector.
2. Check voltage between Intelligent Key unit harness connector M70 terminal 1 and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 6
4.CHECK STEERING LOCK COMMUNICATION SIGNAL
Check signal between Intelligent Key unit connector M70 terminal 32 and ground with oscilloscope. 1 - Ground : Battery voltage
WIIA1202E
4 - Ground
: Continuity should exist.
WIIA1203E
1 - Ground : Approx. 5V
WIIA1204E
Revision: April 20092010 QX56

DLK-100
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
STEERING LOCK UNIT
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 6
5.CHECK STEERING LOCK SOLENOID COMMUNICA
TION CIRCUIT FOR OPEN
1. Disconnect Intelligent Key unit and steering lock solenoid connectors.
2. Check continuity between Intelligent Key unit harness connector (B) M70 terminals 1, 32 and steering lock solenoid connector (A) M15 terminals 2, 3.
Is the inspection result normal?
YES >> Replace steering lock solenoid. • After replacing steering lock solenoid, perform regis-
tration procedure. Refer to SEC-14, "
System Descrip-
tion".
NO >> Repair or replace harness between steering lock sole-
noid and Intelligent Key unit.
6.CHECK STEERING LOCK SOLENOID COMMUNICATION CIRCUIT FOR SHORT
1. Disconnect Intelligent Key unit and steering lock solenoid connectors.
2. Check continuity between steering lock so lenoid connector M15 terminals 2, 3 and ground.
Is the inspection result normal?
YES >> Replace Intelligent Key unit. Refer to SEC-120,
"Removal and Installation".
NO >> Repair or replace harness between steering lock sole-
noid and Intelligent Key unit.
Connector Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 32 Ground Ignition
switch is
pushed
WIIA1205ESIIA1911J
1 - 2 : Continuity should exist.
32 - 3 : Continuity should exist.
ALKIA0661ZZ
2 - Ground : Continuity should not exist.
3 - Ground : Continuity should not exist.
ALKIA0662ZZ
Revision: April 20092010 QX56

A/T SHIFT SELECTOR (PARK POSITION SWITCH)DLK-101
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
A/T SHIFT SELECTOR (PARK POSITION SWITCH)
Diagnosis ProcedureINFOID:0000000005146971
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK A/T SHIFT SELECTOR (PARK POSITION SWITCH) INPUT SIGNAL
1. Turn ignition switch OFF.
2. While pressing the ignition knob switch, check voltage between Intelligent Key unit harness connector M70 terminal 39 and ground.
Is the inspection result normal?
YES >> Replace Intelligent Key unit. Refer to SEC-120,
"Removal and Installation".
NO >> GO TO 2
2.CHECK A/T SHIFT SELECTOR (PARK POSI TION SWITCH) POWER SUPPLY CIRCUIT
1. Disconnect A/T shift selector (park position switch) connector.
2. While pressing the ignition knob switch, check voltage between A/T shift selector (park position switch) harness connector M203
terminal 5 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness or ignition knob switch.
3.CHECK A/T SHIFT SELECTOR (PARK POSITION SWITCH)
Check continuity between A/T shift selector (park position switch) terminals 5 and 6.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace A/T shift selector (park position switch).
4.CHECK A/T SHIFT SELECTOR (PARK POSITION SWITCH) CIRCUIT
Connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (-)
M70 39 Ground Selector lever is in "P" position Battery voltage
Other than above
0
WIIA1211E
5 – Ground : Battery voltage.
ALKIA0663ZZ
Component Terminals ConditionContinuity
A/T shift se- lector (park
position switch) 56Selector lever is in "P" position Yes
Other than above
No
ALKIA0664ZZ
Revision: April 20092010 QX56

REMOTE KEYLESS ENTRY RECEIVERDLK-103
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
REMOTE KEYLESS ENTRY RECEIVER
DescriptionINFOID:0000000005146972
Receives Intelligent Key operation and transmits to Intelligent Key unit.
Component Function CheckINFOID:0000000005146973
1.CHECK FUNCTION
With CONSULT-III
Check remote keyless entry receiver "RKE OPE COUN1" in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES >> Remote keyless entry receiver is OK.
NO >> Refer to DLK-103, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146974
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check remote keyless entry receiver signal with an oscilloscope.
Is the inspection result normal?
YES >> GO TO 2
NO >> GO TO 5
2.REMOTE KEYLESS ENTRY RECEIV ER VOLTAGE CIRCUIT INSPECTION
Monitor item Condition
RKE OPE COUN1 Checks whether value changes when operating Intelligent Key.
Te r m i n a l s
Keyfob
condition Signal
(Reference value)
(+)
(–)
Remote
keyless
entry re- ceiver
connector Te r m i n a l
M25 2 Ground No function
Any button
is pressed
ALKIA0653ZZ
OCC3879D
OCC3880D
Revision: April 20092010 QX56

DLK-108
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
HORN FUNCTION
HORN FUNCTION
DescriptionINFOID:0000000005146978
Perform answer-back for each operation with horn.
Component Function CheckINFOID:0000000005146979
1.CHECK FUNCTION
1. Select "HORN" in “ACTIVE TEST” mode with CONSULT-III.
2. Check the horn (high/low) operation.
Is the operation normal?
YES >> Inspection End.
NO >> Go to DLK-108, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000005146980
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK HORN FUNCTION
Check horn function with horn switch
Do the horns sound?
YES >> GO TO 2
NO >> Go to HRN-4, "
Wiring Diagram".
2.CHECK HORN RELAY POWER SUPPLY
1. Turn ignition switch ON.
2. Perform “ACTIVE TEST”, "HORN" with CONSULT-Ill.
3. Using an oscilloscope or analog voltmeter, check voltage between horn relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 3
3.CHECK HORN RELAY CIRCUIT
Test item Description
HORN ON Horn relay ON (for 20 ms)
ALKIA0658ZZ
Horn relay
Ground Test item Voltage (V)
(Approx.)
Connector Terminal
H-1 1Ground HORN ON
Battery voltage → 0 → Battery voltage
Other than above Battery voltage
Revision: April 20092010 QX56

HORN FUNCTIONDLK-109
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and horn relay connector.
3. Check continuity between IPDM E/R harness connector and horn relay harness connector.
4. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4.CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-35, "Removal and Installation of IPDM E/R".
NO >> Repair or replace the malfunctioning part.
WIIA0679E
IPDM E/R Horn relay
Continuity
Connector TerminalConnector Terminal
E122 45H-1 1Yes
IPDM E/R GroundContinuity
Connector Terminal
E122 45Ground No
Revision: April 20092010 QX56