2010 AUDI S8 ignition

Instrument panel switch
-Press the G!;l switch to extend or retract the electric
sunshade for the rear window =>
page 68, fig. 62.
Rear switch
Press the rn switch to extend or retract the electric
sunshade for the rear window:::;,
page 68, fig. 63.
After the sun shade for the rear window has reached either of its end
positions, it turns off automat ically .
Briefly press the switch a second time to reverse the movement of the
sun shade before it reaches its end position . If the ignition is turned
off while the shade is still moving, the shade will continue until it
reaches the end position before turning off.
The rear w indow sun shade can be set in the MMI so that it retracts
automatically when driving in reverse. Select function button
I CAR I>
Systems > Window > Rear window sun shade> On to do th is . The sun
shade is extended again as soon as the vehicle is traveling forward at
a speed greater than 9 mph (15 km/h) if the ign ition has not been
switched off in the meantime . The current setting is automatically
stored and assigned to the remote key.
[ i ] Tips
• If the sun shade is operated repeatedly within a short time, the
built- in overload protection circuit may be tripped . If this occurs, you
will have to wait briefly before you can operate the shade again.
• Because of the decrease in the flexibility of the shade material at
temperatures below freezing, the e lectrica l circuit which operates
the shade shuts off when the temperature in the vehicle falls below
23 °F
( - 5 °C) . The shade cannot be operated until the passenger
compartment warms up above this temperature .•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
App lies to veh icles : wi th electric sunshad e fo r the r ear sid e w in dow s
Electric sunshade for the rear side windows
Each rear side window is equipped with an electric
sunshade.
Fig. 64 Roofli ning in
the rear: electric
su nshade but ton
You can operate the rear side window sunshades either by
using the power window switches in the driver's door, the
power window switches in the rear doors or the button
located in the rooflining in the rear of the vehicle .
Buttons in the rear of the vehicle
-Press the right or left button to lower or raise the
sunshade=> fig. 64.
Power window switch in the rear side doors
- Pull the switch to its second position and hold it there
briefly to lower the sunshade .
- Press the switch to its second position to raise the
sunshade.
Vehicle care Do-it-yourselt service iTechnical data

Intermittent wiping ~l (acti vating rain
sensor )
- Move the lever up to position (D.
- Move switch @up or down , to adjust the sensitivity of the
rain sensor.
Low wip er sp eed
- Move the lever up to position@.
High wiper speed
- Move the lever up to position ®·
One-touch wiping
- Move the lever to position@, when you want to wipe the
windshield
briefly .
Automatic wiper /washer
- Pull the lever to position © (toward the steering wheel)
and hold.
- Release the lever . The washer stops and the wipers keep
going for about four seconds.
Turning off the wipers
- Move the lever back to positio n@ .
The windshield wipe rs and washer only work when the ignition is
turned on.
T he rain sensor is only activated with the wiper leve r set to position
@ . When i t starts to rain, the rain sensor will automatically activate
the intermittent wiping mode .
T o red uce the sensit iv ity of the senso r, move sw itch @down. To
increase the sensitivity, move the switch up . The higher you adjust the
Controls and equip ­
ment Safety first
Clear v
ision
sensitivity, the faster the sensor will react when it senses mo isture on
t he windsh ie ld. T he rain senso r wiper inte rvals depend on the sensi­
tiv ity setting as well as vehicle speed . During brief stops, w iper
motion will adj ust in relation to the amount of rain on the winds hield.
Dur ing b rief stops, e .g . at a red light , w iper motion will automatically
be reduced to the next lower speed. Wipers already turn ing at low
speed. c hange to intermittent w iping.
When the ign ition is turned on, the washer jets are heated.
With the low beam headlights switched on, pull the wiper lever
towards you o nly
briefly to clean the w indshield . Holding the wiper
lever would also engage the headlight washer system each time you
clean the w indshield and would d rain the washer fluid rese rvoir
prematurely .
& WARNING
• Wiper bl ade s a re cruci al for safe dri ving! Only when the y are in
good condition are th ey able to clear the wind ows properly to
pro vide uncompr omi sing visibilit y. Worn or damaged wipe r
blade s ar e a safet y hazard =>
pag e 73, "In stalling new wiper
blades "!
• The rain sensor i s only des igned t o assist and support the
dri ver. It rem ain s entirely the d river's re spon sibility to m onito r
out side weather condition s and to manually a ctivate the wipers as
soon a s rain or dr izzle reduce s visibil ity th rough the windshield.
• The win dshield mu st not be treated with wat er- re pellent
m aterial s. They c an in crease gla re under po or visibilit y condit ions
s u ch as wetn ess, darkne ss, or when the sun i s low on the horizon .
In addition , they can cause the wi ndshield wipers to chatter.
0 Note
In freezing or near freezing conditions:
• Always check that the wiper blades a re not frozen to the glass
before you turn the wipers on. Loosen a wiper blade which is fro zen in ..,
Vehicle care Technical data

Clear vision
place before operating the wipers to prevent damage to the wiper
blade o r th e wiper motor.
• Do not use the wipers to clear a frosted window. Us ing the wipers
as a convenie nt ice scraper wi ll dest roy the w iper blades .
• Before you take your vehicle to an automatic car wash, make sure
you have the w ind shield wipe r sys tem sw itched off (lever in posi tion
0), otherw ise the windshie ld wiper system cou ld get damaged in the
car w ash if i t shou ld sudden ly come on.
[ i ] Tips
• Make s ure the washe r flu id reservoir in the eng ine compa rtment is
topped off before going on a long trip . Look up~
page 305 for
check ing and filling the washer conta iner.
• If you switch off the ignition with the w indshield wiper lever still
in the inte rval wipe posit io n and then come bac k a w hile la ter and
dr ive off, the rain sensor will reactivate itself afte r the ve hicle speed
has exceeded 4 mph (6 km/h).
• Worn or d irty windshield w iper blades cause smear ing which can
affect the operation o f the rain senso r. Check the cond it io n of your
w indshield wiper b lades regularly .•
Headlight washer system
The headlight washer system cleans the headlights.
- Operate the wi ndsh ield wip er/was her syst em ® with the
headlig hts turned on by hold ing the lever for lo nger than
one second=>
page 70, fig. 67 .
The washer je ts extend fo rwa rd o ut of the front bumper driven by
water pressure to spray the front headlights w ith water .
You should inspect the headlights regu larly (for example when refu­
eling) and clean off a ny solid dirt o r insects from the lenses. To ensure the system works properly in winter, keep the washer jets
free o
f snow and remove any ice using a de- ic ing spray. •
Service position
The wiper blades can only be changed in the service posi ­
tion.
- At below freezing outside temperatures, make sure first
that the wiper blades are not frozen to the windshield .
- Select: Function b utt on
I CAR ]> System s > Windshield
wipers .
- Select Serv ice position on t o tu rn th e service position on
or
off to return t he windsh ield w iper to its or ig inal pos i­
tion.
You must only attempt to change the wiper b lades when the service
position is act ivated. This way, when you are working on the wind­
shield wipe rs, you can avoid damaging the paint on the engine hood.
[ i ] Tips
• You can also turn on the se rvice position, for examp le, if you want
to protect the windshield from ic ing, using a cover .
• T he service position t urns itself
off , whenever yo u use the w ind­
shield wiper lever .•

Clear vision
Mirrors
Rear view mirror
When the ignition is on, t he interior m irro r will darken automatically
depending on t he amo unt of light strik ing the m irro r (such as head­
lights shin ing into the veh icle from the rear) . The mirro r will retu rn to
the o rigi na l state (anti -glare off) when yo u move the manua l gear­
shift/gear se lector lever into
Reverse or w he n you turn o n the in te rior
lights .
& WARNING
Broken glass of automatic dimming mirror can cause electrolyte
fluid l eakage . Electrolyte fluid can irritate skin, eyes, and respira­
tory system .
• Repeated or prolonged exposure to electrolyte can cause irrita ­
tion to the respiratory system , especially among people with
asthma or other respiratory conditions . Get fresh air immediately
by leaving the vehicle or , if that is not possible , open windows and
doors all the way .
• If electrolyte gets into the eyes , flush them thoroughly with
large amounts of clean water for at least 15 minutes; medical
attention is recommended.
• If electrolyte contacts skin, flush affected area with clean
water for at least 15 minutes and then wash affected area with
soap and water; medical attention is recommended. Thoroughly
wash affected clothing and shoes before reuse.
• If swallowed and person is conscious, rinse mouth with water
for at least 15 minutes. Do not induce vomiting unless instructed
to do so by medical professional. Get medi cal attention immedi­
ately.
[I] Tips
T he au tomati c anti-glare feature on the mi rro r will not operate prop­
erly if the lig ht shini ng on the inside mir ror is blocked by othe r
objec ts. •
Outside mirrors
The outside mirrors are elec trically a djust ed.
Adjusting the outside mirrors
Fig . 70 F orw ard
section of d river 's
armrest : power mi rro r
c on trols
- Tur n th e ad jus ting k nob to posi tion (0 ~ fig. 7 0 to ad just
the outside m irror on the drive r's s ide.
- Tur n the k nob to posit io n ® to adjust t he out side mirror
on the passe nger side.
- Pr ess t he knob i n th e ap propriate direc tion to move t he
mirror s urf a ce so tha t you have a goo d view to the r ear .
Folding both outside mirrors in flush
- Turn the knob to@ .
The m irro r sur faces are heated whe never you switch on the rear
w indow defogger in re sponse to the o utside temperature.

Seats and storage
& WARNING
• Never adjust the driver's or front passenger's seat while the
vehicle is moving. If you do this while the vehicle is moving, you
will be out of position. Always adjust the driver's or front passenger's seat when the vehicle is not moving.
• Be careful when adjusting the seat height. Check to see that no
one is in the way, or serious injury could result!
• Because the seats can be electrically adjusted with the ignition
key removed, never leave children unattended in the vehicle.
Unsupervised use of the electric seat adjustments may cause
serious injury. •
Upper thigh support
The adjustable upper thigh support provides optimal
support for the upper thigh when driving.
___ .. _:_·_-_.-_--·-·------·---.... _-_ ---.. ·-:.-_
Fig. 72 Power seat:
Switch for upper thigh
support
- To extend the upper thigh support , push the switch
forward.
- To make the upper thigh support shorter, push the switch
to the rear.
& WARNING
Never adjust the seat cushion while the vehicle is moving. If you
adjust your seat while the vehicle is moving, you are out of posi­
tion. Always adjust the seat cushion when the vehicle is not
moving. •
Seat adjustment
Fig. 73 Power seat:
Switch for seat adjust­
ment
Moving the seat forward and backward (D
- Press the switch forward or backward horizontally=>&.
Adjusting the seat height 0 and ® together
-Pull the switch evenly at both ends to raise the seat =:>& .
-Push the switch evenly at both ends to lower the seat
=> & .
Angling the seat cushion up and down@ or®
-To angle the seat cushion up, pull the switch at the front
only =>& .
-Alternatively, push the switch at the rear only=>& . .,_

-To angle th e s eat c ush io n down, push the sw itc h at the
front only:::::, &.
-Alt ernatively, pull the switc h at the rear only:::::,&.
& WARNING
• Never adjust the driver's or front passenger's seat while the
v ehicle is moving . If you do this while the veh icle is moving , you
will be out of po sition. Alway s adjust the driver's or front
pa ssenge r's seat when the vehicle is not mo ving.
• Be careful when adjusting the seat height. Check to see that no
one is in the way , or serious injury could result!
• Becau se the seat s can be el ectrically adjusted with the ignition
key removed, never leave children unattended in the vehicle.
Unsupervis ed use of the electri c seat adjustments may cau se
seriou s inju ry. •
Applie s to ve hicl es: with ma ssag e funct ion
Massage function
0 0
i
Fig . 74 P ow er s eat:
M assa g e f unc tion
- Press the sw itc h to turn on the massage function .
The mass age funct ion r uns fo r abo ut 10 m inutes . The passenger's
back is massaged by contin uous adjustment of the lumbar support .
Contro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
The curvature of the lumbar support can also be adjusted during the
Massage to m ake it more or less aggressive. This v aries the intens ity
of t he
Massage to the leve l desired by the occupa nt.
Once the massage f unctio n stops after abo ut 10 min utes, the lumbar
s u pport a utomat ically retu rns to the posi tion i n wh ich it wa s last set.
[ i ] Tips
Th e massage f unct io n can be interrupte d at any time by pressing the
switch . The lumbar support remains in its current position. •
Adjusting the seatback
-0
i
Fig. 75 Power se at:
S w itch f or seat bac k
ang le
F ig. 76 Pow er se at:
S witch f or a dju st ing
uppe r seatba ck se ction ...
Vehicle care Do-it-yourselt service iTechnical data

Individual rear seats
Applies to vehi cles: wit h in divi dua l rear sea ts
Controls
The operating logic for the s witches corresponds to the
construction and function of the seat.
Fig . 8 7 Con trols f or
individu al re ar sea ts
The switch es to ad just the seats correspond to th e layout, the design
and the func tion of the seat . The seats a re adjusted by mov ing the
switches following this logic .
@ Seat adjustmen t
® Massage funct ion*
© Head r estraint adjustment
@ Lu mb ar sup po rt
& WARNING
• Vehicles with power individual rear seats h ave seating for four.
T he lo ng ce nter console between the two rear seats is not a seating
p os ition. Therefore, a safety belt is not provided.
• The power adjustment for the individual se ats also wo rk s with
the ign it ion switched off or with the ign ition key removed . For this
reason , children should never be left unattended in the vehicle·
they could be injured!
Cont rols a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
& WARNI NG (continued )
• Exerci se caution when adju sting the seats. Unsupervised or
c arele ss seat adjustment can pinch fingers or hand s caus ing
injuries .•
A pp lies to vehicles : w it h ind iv idual rear sea ts
Seat adjustment
Seat forward/back ©
- Push the swi tch forward or back=}& .
Seat angle up/down@
- Push the switch up or down=}& .
& WARNING
Fig. 8 8 Individ ual re ar
s ea ts: S eat a dju stme nt
• Vehicles w ith power indi vidu al rear seats ha ve seating for four.
The l ong cent er cons ole between the two re ar se ats i s not a seating
position. The refore , a safety belt is not provided .
• The power adjustment for the individual seats also work s with
the ign ition switched off or with the ignition key remo ved . For th is
reason, children sh ould never be left un attended in the vehicle ·
they could be injured! .,,.
Vehicle care Do-it-yourselt service iTechnical data

Cigarette lighter/socket
Cigarette lighter
Using the cigarette lighter
-Push the knob in .
Fig. 103 Open ashtray
with cigarette lighter
Fig . 104 Center
console rear: Cigarette
lighter
- Wait until the cigarette lighter knob pops out.
- Remove the cigarette lighter immediately and use it.
- Reinsert cigarette lighter into the socket after use.
Connecting an appliance
-Remove cigarette lighter.
Contro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
-Plug in app liance to be used.
The socket of the cigarette lighter may be used for 12-volt appliances
with maximum consumption of up to 100 watts, such as a flash light,
small vacuum cleaner, etc.
Before you purchase any accessories, always read and follow the
information in~
page 363 , "Additional accessories and parts
rep lacement" .
& WARNING
Improper use of the cigarette lighter can cause serious injury or
start a fire.
• Be careful when using the cigarette lighter. If you do not pay
attention to what you are doing when you are using the cigarette
lighter you can burn yourself.
• The cigarette lighter and socket remain functional even if the
ignition is switched off or the ignition key is removed . Never leave
children inside the vehicle without supervision.
0 Note
• To avoid damag ing the socket, only use plugs that fi t properly.
• Only use the cigarette lighter socket as a power source for e lec­
trical accessories for short durations. Use the sockets in the vehicle
when a power source is needed for longer durations .
[ i ] Tips
Whe n the engine is off and accessories are still plugged in and are on,
the vehicle battery can still be drained.•
Vehicle care Do-it-yourselt service iTechnical data