2010 AUDI S8 service

& WARNING (continued)
• Never leave children or persons requiring assistance alone in
the vehicle, especially when they could access the vehicle keys.
Unsupervised use of the keys can result in the engine being started
or use of vehicle systems such as the power windows, etc. which
could result in serious injury. The doors could be locked with the
remote key, delaying help in an emergency.
• The power sunroof will continue to operate until the ignition
key has been removed and one of the front doors has been
opened. a
Emergency closing by hand
The sunroof can be closed by hand in case of a power
failure.
Con tro ls a nd e quip ­
m en t
Fig. 46 Section from
headliner: Where to
place the screwdriver
Vehicle OP-eration
Removing the cover
Opening and closing
Fig. 47 Section from
headliner: Crank for
emergency operation
- Insert the flat side of the screwdriver (found in the vehicle
tool kit) at the rear edge of the lens as indicated by the
-arrows- ::::> fig. 46.
- Carefully pry the clear lens cover open and remove it.
Retrieving the crank for emergency closing
-Use the ignition key or a screwdriver to carefully pry the
cover off the left end of the instrument panel
=> page 342, fig. 276. The crank is stored next to the fuse
carrier.
Closing the roof
- Push the crank ©::::> fig. 47 into the hex socket@ until
you can feel the crank engage. Start turning, maintaining
a steady pressure on the crank to keep it from slipping off.
- After you have closed the sunroof, remove the crank and
replace the dome light lens.
[ i] Tips
If you are unable to close the roof manually, contact the nearest
authorized Audi dealer for assistance. •
Vehicle care Do-it-yourselt service iTechnical data

Appli es to veh icles: w ith Adap tive Ligh t
Adaptive Light
When making a turn or driving around tight corners, the
relevant area of the rood is better illuminated .
Adaptive Light (making turns)
Fig. 51 Ada ptive Li ght
when turnin g and
dr iv ing th roug h cu rv es
An additional bulb in the headlight prov ides a corner ing light @ in
addition to the low beam ©~ fig. 51. Adapt ive Light is switched on
and off automatically depending on dr iv ing cond itions.
When you activate the turn signal lever, the Adaptive Light for the
same s ide is sw itched on. Please note that the t urn signal lever must
engage.
Adaptive Light is not switched on if you on ly move the turn signal
lever to the point of resistance to s ignal a lane change~
page 64,
"Turn signal ¢i c:> and high beam ~o lever".
When d riving arou nd bends, Adaptive Light is con tro lled according to
steering wheel angle.
• It is switched on in tight corners.
• It is not switched on in long, open bends .
Adaptive Light (in curves )
When driving through curves, the low beams © are automatica lly
cont rolled depending on driving speed and the steer ing w heel angle.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
The two main beams p ivot at d ifferent angles so that there is no unil­
l u mi nated area in front of the vehicle .
[ i ] Tips
• T he system works up to a speed of abo ut 4 3 mph (70 km/h). If the
speed is higher, it is not activated .
• Adaptive Light ( in curves) func tions at a speed of abo ut 6 mph
(10 km/h) and is deactivated at speeds below abo ut 4 mph
(6 km/h). •
Emergency flasher ~
The emergency flasher makes other motorists aware that
you or your vehicle ore in on emergency situation.
7A I
Fi g. 52 Cen ter
c on sol e: e mergen cy
f la sh er swit ch
-Press the switch ~~ fig. 52 to turn the emergency
flashers on or off.
When the emergency flasher is on, all four turn signals blink at the
same time. The t urn signal indicator ligh ts
¢i Q in the instr ument
cluster, as well as the light in the emergency flas her switch ~ blink
likewise .
Th e eme rgency flashers wi ll turn on automat ically if yo u are in a n
acc ident where the airbag has deployed.
Vehicle care Do-it-yourselt service iTechnical data

0 Note
Do not use the high beam or headlight flasher if you know that these
could blind oncoming traffic. •
Interior lights
Front interior Lights
The interior lights include reading lights for both the
driver and the front passenger.
11111111
I
\ 10
1
111111111
0
Con trol s and equ ip­
m ent
111 i -~ -
--
•l l i'1~
rol ,
l I
111111111
i8 M
-w
"' a,
' '
111111111
0 Fig. 54 Rooflining:
Front interior lights
Fig. 55 Rooflining:
Front reading lights:
Vehicle OP-eration
Clear vision
Interior lights
- Press the@) button to turn off the interior lights
~ fig. 54. If you press the button a second time, the inte­
rior lights in the rear are also turned off.
- Press the
(ID button to turn on the door contact circuit.
Press the button a second time to turn on the door contact
circuit for the rear doors .
- Press the
(I) button to turn on the interior lights. If you
press the button a second time, the interior lights in the
rear are also turned on .
Reading lights '-<~
-Press the switch to turn the right or left reading light on
or off ~ fig. 55.
With the door contact circuit, (ID the interior lights turn on as soon as
you unlock the vehicle or open the doors. The in terior lights are also
turned on when the ignition key is removed. The light goes out about
2 minutes after the doors are closed . When the vehicle is locked or
when the ignition is turned on, the interior lights are turned off .
When a door is open, the interior lights are turned off after about 10
minutes to preven t draining the battery.
[ i] Tips
The interior lights can be dimmed by holding the(!) swit ch pressed
down. If the interior lights in the rear were turned on by pressing the
switch twice, the rear interior lights are also dimmed .•
Vehicle care Do-it-yourselt service iTechnical data

Applies to vehicles: with background lighting
Background lighting
Four different lighting profiles for the interior lighting
con be selected and dimme d through the
MMI.
111111111
0
{m\ \1-=---.=J
~ "'"""
~o
Fig. 58 MMI di splay:
B ac kg round lighting
Fig . 59 Roo f mod ule
c ut out: Ligh t prof ile
s wit ch
-Press the Systems control but ton in the car menu .
- Selec t
Background lighting .
-Select a lighti ng profile => fig . 58 or select Off to deact i-
vate the lighting profile.
- Press the co ntrol knob to activate the des ired lig hting
profile.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
- Rotate the control knob clockwise to increas e the bright ­
ness, and
- Rotate the control knob
counterclockwise to reduce the
brigh tness.
Whe n the vehicle is unlocked, the sta ndard lighting turns on a uto­
matically and dims after approx. 2 minutes, and when the ignition is
turned on i t sw itches off immediate ly.
A background lighting prof ile can be switched on manually us ing the
ligh t profile switch => fig. 59. This w ill turn off a utomat ica lly aft er 30
m inutes when the ig nitio n is off . To reactivate, press the lighting
profile sw itch .
L ighting profi les that were selected while driving rema in act ive
dur ing the course of travel.
The following lighting profil es can be adjusted and
dimmed in the MMI:
Lighting profile Highway City Cockpit Rear
Drive r's side footwell X
Passenger's side foot-X X well
Rear footwell
X X
Front door trim panel X X X
Rear door trim panel X X X X
F ront int erior lighting X X
Rear interior light ing X X
II) Tips
Lighting profiles are stored on the remote control key being used .•
Vehicle care Do-it-yourselt service iTechnical data

Instrument panel switch
-Press the G!;l switch to extend or retract the electric
sunshade for the rear window =>
page 68, fig. 62.
Rear switch
Press the rn switch to extend or retract the electric
sunshade for the rear window:::;,
page 68, fig. 63.
After the sun shade for the rear window has reached either of its end
positions, it turns off automat ically .
Briefly press the switch a second time to reverse the movement of the
sun shade before it reaches its end position . If the ignition is turned
off while the shade is still moving, the shade will continue until it
reaches the end position before turning off.
The rear w indow sun shade can be set in the MMI so that it retracts
automatically when driving in reverse. Select function button
I CAR I>
Systems > Window > Rear window sun shade> On to do th is . The sun
shade is extended again as soon as the vehicle is traveling forward at
a speed greater than 9 mph (15 km/h) if the ign ition has not been
switched off in the meantime . The current setting is automatically
stored and assigned to the remote key.
[ i ] Tips
• If the sun shade is operated repeatedly within a short time, the
built- in overload protection circuit may be tripped . If this occurs, you
will have to wait briefly before you can operate the shade again.
• Because of the decrease in the flexibility of the shade material at
temperatures below freezing, the e lectrica l circuit which operates
the shade shuts off when the temperature in the vehicle falls below
23 °F
( - 5 °C) . The shade cannot be operated until the passenger
compartment warms up above this temperature .•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
App lies to veh icles : wi th electric sunshad e fo r the r ear sid e w in dow s
Electric sunshade for the rear side windows
Each rear side window is equipped with an electric
sunshade.
Fig. 64 Roofli ning in
the rear: electric
su nshade but ton
You can operate the rear side window sunshades either by
using the power window switches in the driver's door, the
power window switches in the rear doors or the button
located in the rooflining in the rear of the vehicle .
Buttons in the rear of the vehicle
-Press the right or left button to lower or raise the
sunshade=> fig. 64.
Power window switch in the rear side doors
- Pull the switch to its second position and hold it there
briefly to lower the sunshade .
- Press the switch to its second position to raise the
sunshade.
Vehicle care Do-it-yourselt service iTechnical data

Clear vision
place before operating the wipers to prevent damage to the wiper
blade o r th e wiper motor.
• Do not use the wipers to clear a frosted window. Us ing the wipers
as a convenie nt ice scraper wi ll dest roy the w iper blades .
• Before you take your vehicle to an automatic car wash, make sure
you have the w ind shield wipe r sys tem sw itched off (lever in posi tion
0), otherw ise the windshie ld wiper system cou ld get damaged in the
car w ash if i t shou ld sudden ly come on.
[ i ] Tips
• Make s ure the washe r flu id reservoir in the eng ine compa rtment is
topped off before going on a long trip . Look up~
page 305 for
check ing and filling the washer conta iner.
• If you switch off the ignition with the w indshield wiper lever still
in the inte rval wipe posit io n and then come bac k a w hile la ter and
dr ive off, the rain sensor will reactivate itself afte r the ve hicle speed
has exceeded 4 mph (6 km/h).
• Worn or d irty windshield w iper blades cause smear ing which can
affect the operation o f the rain senso r. Check the cond it io n of your
w indshield wiper b lades regularly .•
Headlight washer system
The headlight washer system cleans the headlights.
- Operate the wi ndsh ield wip er/was her syst em ® with the
headlig hts turned on by hold ing the lever for lo nger than
one second=>
page 70, fig. 67 .
The washer je ts extend fo rwa rd o ut of the front bumper driven by
water pressure to spray the front headlights w ith water .
You should inspect the headlights regu larly (for example when refu­
eling) and clean off a ny solid dirt o r insects from the lenses. To ensure the system works properly in winter, keep the washer jets
free o
f snow and remove any ice using a de- ic ing spray. •
Service position
The wiper blades can only be changed in the service posi ­
tion.
- At below freezing outside temperatures, make sure first
that the wiper blades are not frozen to the windshield .
- Select: Function b utt on
I CAR ]> System s > Windshield
wipers .
- Select Serv ice position on t o tu rn th e service position on
or
off to return t he windsh ield w iper to its or ig inal pos i­
tion.
You must only attempt to change the wiper b lades when the service
position is act ivated. This way, when you are working on the wind­
shield wipe rs, you can avoid damaging the paint on the engine hood.
[ i ] Tips
• You can also turn on the se rvice position, for examp le, if you want
to protect the windshield from ic ing, using a cover .
• T he service position t urns itself
off , whenever yo u use the w ind­
shield wiper lever .•

Installing new wiper blades
Wiper blades in good condition help keep the windshield
clear .
Removing a wiper blade
Fig. 68 Rem ov in g th e
wi per bla des
F ig . 69 Installi ng
wip er b lad es
- Bring the windshield wipers to the se rvice posi tion
~ page 72.
- Lift the wiper arm away from the windshield .
- Push the locking piece on the wiper blade in the direct ion
of t he arrow @~ fig . 68 . Ho ld the wipe r blade firmly.
- Remove the w iper blade@.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
Installing wiper blade
- Place the new wiper b lade in th e retaine r on the wiper arm
@ ~fig. 69.
- Push the locking piece on the wiper blade in the direction
o f the arrow ® until you feel it click into place on the
wrper arm.
Clean your wiper blades regular ly with a windshie ld washer so lution
to p revent streaking.
If the b lades are very dirty, for example wi th
insects, carefu lly clean the blades with a sponge or a soft brush .
If the w iper blades begin to streak the w indshield, this could be
caused by res idue left on the windsh ie ld by au tomatic car washes .
Fill the windshie ld washer container with a specia l solution availab le
a t you r author ized A udi dealer to remove the res idue.
& WARNING
Be sur e to in spe ct the conditi on of your wiper blades regularly . See
your authorized Audi de ale r for replacement blades .
0 Note
To prevent damage to the wiper system:
• Always loosen blades wh ich are frozen to the wi ndshield before
operating wipers.
• Do not use gasoline , ke rosene, paint th inner, or ot her solvents on
or near the wiper blades .
• Do not at tempt to move the w ipers by hand.
[I] Tips
Commercial hot waxes applied by automatic car washes affect the
cleanability of the windshield. •
Vehicle care Do-it-yourselt service iTechnical data

-Position the head restraint according to the occupant's
height ~
page 81. For maximum protection, the top of
the head restraint should be at least at eye level, prefer­
ably higher and ideally level with the top of the head
~ page 191, fig. 200.
& WARNING
Never place any objects in the driver's footwell. An object could
get into the pedal area and interfere with pedal function. In case
of sudden braking or an accident, you would not be able to brake
or accelerate. •
Front passenger's seat
Always move the front passenger seat into the rearmost
position.
To avoid contact with the airbag while it is deploying, do not
sit any closer to the instrument panel than necessary and
always wear the three-point safety belt provided adjusted
correctly. We recommend that you adjust the passenger 's
seat in the following manner:
- Move the front passenger seat into the rearmost position
of the fore and aft adjustment range~
& in "Why is your
seat adjustment so important?" on
page 76.
- Bring the backrest up to an (almost) upright position.
Do
not ride with the seat reclined.
- The ideal position for the head restraint is with the upper
edge of the restraint level with the top of your head
~ page 81. You should not lower the top of the restraint
below the level of your eyes.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
-Place your feet on the floor in front of the passenger's
seat. •
Power seat
Controls
The operating logic for the switches corresponds to the
construction and function of the seat.
Fig. 71 Power seat:
Controls for seat
adjustment
The switches to adjust the seats correspond to the layout, the design
and the function of the seat. The seats are adjusted by moving the
switches following this logic.
© Upper thigh support~ page 78
@ Seat adjustment ~ page 78
© Massage funct ion* ~ page 79
@ Seatback angle~ page 79 and head restraint~ page 81 adjust-
ment
© Separa te adjustmen t of upper sea tback section ~ page 79
© Adjusting the lumbar support~ page 80
© Safety belt height adjustment~ page 204 ..,
Vehicle care Do-it-yourselt service iTechnical data