2010 AUDI A5 COUPE brake light

___ T_ r _a_ il_e _r_ t_ o_ vv_ in__... g,_ __________________________________________________ _
Observe speed limits. In some areas, speeds for vehicles towing
trailers are lower than for regular vehicles.
Always apply brakes early. When driving downhill, shift into a lower gear to use the engine braking effect to slow the vehicle. Use of the
brakes a lone can cause them to overheat and fail.
Coolant temperature
The coolant temperature gauge=> page 8 must be observed care­
ful ly . If the needle moves close to the upper end of the scale, reduce
speed immediately and/or turn off the air conditioner .
If the coolant temperature warning light in the instrument cluster
starts flashing
-F- , pul l off the road, stop and let the engine idle for
about two minutes to prevent heat build-up .
& WARNING
Anyone not properly restrained in a moving vehicle is at a much
greater risk in an accident. Never let anyone ride in your car who
is not properly wearing the restraints provided by Audi . •
Trailer towing tips
Important to know
----------------
Your vehicle handles differently when towing a trailer because of
the additional weight and different weight distribution. Safety,
performance and economy will great ly depend on how careful ly you
load your trailer and operate your rig.
Before you actual ly tow your trailer, pract ice turning, stopping and
backing up in an area away from traffic. Keep practicing unti l you
have become completely familiar with the way your vehicle -trailer
combination behaves and responds . Backing
up is difficult and requires practice . Backing up with a
t rai ler genera lly requires steering action opposite to that when
backing up your vehicle without a trailer .
Maintain a greater distance between your vehicle and the one in
front of you. You will need more room to stop . To compensate for
the trai ler, you wi ll need a larger than norma l turning radius.
When passing, remember that you cannot accelerate as fast as you
normally would because of the added load. Make sure you have
enough room to pass. After passing, al low plenty of room for your
trai ler before changing lanes again .
Avoid jerky starts, sharp turns or rapid lane changes.
[ i ] Tips
• Do not tow a trailer during the break -in period of your vehicle.
• If you tow a trailer, your Audi may require more frequent mainte­
nance due to the extra load=>
page 339. •
Parking on a s•ope
Do not pork on a slope with a trailer. If it cannot be
avoided, do so only ofter doing the following:
When parking:
Apply the foot brake.
- Have someone p lace chocks under both the vehicle and
the trailer wheels.
With chocks in place, slow ly release the brakes until the
wheel chocks absorb the load.
- Turn the wheels towards the curb.
- Apply the parking brake.

-Cleaning and prot ection
P'tr:1-~--------------
Cleaning and protection
General information
Regular ca re p rese rves vehicle value .
Any automobile is exposed to industrial fumes, corrosive road salt ,
muddy dog feet, e tc. A wel l cared fo r Audi can look l ike new many
years after purchase . Regu lar and correct care will contribute to
maintaining the beauty and va lue of your Audi .
Fu rthe rmo re , g ood care ma y be a conditi on for sub sta ntiating a
warr anty cla im should corro sion damage or paint defect s occur .
Your authorized Audi dealer has a var iety of dedi cat ed vehicle -care
product s
and can advise which ones to use for cleaning the exterior
and interio r of your vehicle.
Whether you use products recommended by Audi or other commer ­
cially availab le cleaning agen ts, please make su re you apply them
correctly .
& WARNING
• Cleaning agents m ay be poi sonou s. Keep them out of the re ach
of childr en.
• Heed all cau tion label s.
• Alway s read direction s on the container before u sing any
produ ct. Follo w the dire ction s carefull y.
• Most chemi cal cle aner s are concentr ated and h ave to be
d iluted .
• Use spot remo ving fl uid s onl y
in well ventila ted are as.
• Do not use gasoline , kero sene , diesel fuel , nail poli sh remover
or other vol atil e fluid s. They may be to xic , fl ammab le or h azardou s
in other wa ys. Do not wa sh , wax or dry the vehicle w ith the igni ­
tion on or the engine ru nning .
& WARNING (continued )
• Do not clean the unders ide s of cha ssi s, fenders , wheel cover s,
et c. without pr ote cting y our hands and arm s. You may cut your self
on sh arp-edged metal part s.
• Moisture and i ce on brakes may impair br aking eff icien cy
~ page 237, "General information ". Test the brake s carefully each
time you wash the vehicle .
'£> For the sake of the environment
Select only environmenta lly friend ly c leaning products. Leftover
clean ing products should not disposed of in the household waste .•
Care of exterior
Washing
F requent washing protects the vehicle.
The best protection against environmental influences is frequent
washing a nd waxing. How often this is required depends on :
• How much the vehicle is used
• Where the vehic le is pa rked (garage, in the open under trees,
etc.I
• The seasonal and weather cond itions
• Environmental influences
The longer bird dropp ings, insects, tree resin, road and industrial
grime, tar, soot, road salt and other materials remain on the vehicle
b ody, the more lasting their destructive effects will be. High temper ­
atures caused by exposure to intense sunlight intensify the corro -
sive effect, particularly when humidity is high as wel l. .,

___ C_ le_ a _ n_i_n ~g _ a_ n_ d __ p_r _o _t _e _c_ t_ i_o _n ___________________________________________ _
Cast (light) alloy wheels
Cast (light) alloy w heels require special care.
- Wash the wheels with a sponge or hose brush every
o th er week .
- For deep cleaning afte rwards, use only a dedicated
acid ­
free
cast a lloy wheel c leaner.
- Rub a coat of
liquid wa x onto the rims every t hree month.
Be sure to reac h and treat all parts of the rim.
To preserve the decorative appearance of the cast alloy wheels,
some special care is necessary. In add ition to road dirt and salt,
brake dust is also corrosive . If left on for too long, brake dust can
cause p itting.
Use on ly spec ial
acid -free cleaners formu lated for a lloy rims . Safe
products are available at your authorized Audi dealer. Never leave
t he cleaner on the rims longer than specif ied on the label. If not
rinsed off promptly, the acid contained in some cleaners can attack
t he threads on t he wheel bolts.
Never use abrasive or metal po lishing c leaning agents . If the protec ­
t ive coating has been chipped, e.g . by kicked up road dirt, touch it
up as soon as possible.
& WARNING
• Moi sture and ice on b rake s ma y affe ct b raking effi cienc y
=> page 23 7, " General information ". Te st the brakes carefully ea ch
t ime you wa sh the vehi cle .
• Always read and heed all WARNINGS and other informat ion
=> page 25 2. •
Body cavity sealing
T he body c avity se aling does n ot need to be c hecked .
All body cavities which could be affected by corrosion have been
th or ough ly pro tected at the factory .
T his sealing does not require any inspection or additional treat ­
ment . If any wax should seep out of the cavity when the ambient
temperature is high, it can be removed with a p lastic scraper and a
suitable solvent.
& WARNING
Solvent s can be dangerou s.
• Ben zine is flamm able and to xic . If you use benzine for removing
the wax , keep sparks , flame and lighted cigarettes away . Never
dump benz ine on the ground , into open streams or do wn se w age
drains .
• Be sure to observe all safet y and env ironmental regulations .
Follow all in stru ctions on the conta iner .
• Alway s read and heed all WARNINGS and other info rm ation
=> page 2 52 . •
Chassis
Have the underc oating checked for damage from time to
time.
T he lower body shell of your Audi is also thoroughly protected
against corrosion.
Any damage to the undercoating ca used by r oad ha zards shou ld be
repaired promp tly .
& WARNING
Too much undercoating in the wrong pla ces can cause a fire .

•---=C:.:h..:. e=-= c..:.k :..:.in :..:.:= g:.....= a..:.n :.:d::....:. f.:.:il .:.:li ..:.n :..::g~ --------------------------------------------
0 Not e
• Coolant pollutes the environment and cou ld cause an engine
fire. Excess coolant will be forced out through the pressure relief
valve in the cap when the engine becomes hot.
• If, in an emergency, only water can be added, the correct ratio
between water and antifreeze ~
page 277 must be restored as soon
as possible .
ci> For the sake of the environment
Dra ined coolant should not be reused . Always dispose of used
coolant whi le observing all environmental regulations. •
Radiator fan
The radiator fan switches on automatically by itself.
The rad iator fan is driven by the eng ine v ia the V-be lt . The v iscous
clutch regulates the speed of the fan according to the tempera ture
of the coo lant .
An auxiliary electric radiator fan * swi tches on and off depending on
coo lant temperature and other vehicle operating conditions.
After you switch the engine off, the auxiliary fan can continue running for up to 10 minut es -even with th e igni tion o ff. It can even
switch o n again later by itself~ & , if
• the temperature of the engine coo lant rises due to the heat
bui ld -up from the engine in the engine compartment, o r
• the engine compartment heats up because the vehic le is parked
in intense sun light.
& WARNING
• To reduce the ri sk of per sonal injury never tou ch the radiator
f a n.
& W AR N ING (continu ed )
• The auxiliary e le ctri c fan i s temperature controlled and can
s w itch on suddenly even when the engine is not running .
• The auxiliary radiator fan swit ches on automatically when the
engine coolant reache s a ce rtain temperature and will con tinue to
run until the coolant t emperatur e drop s. •
Brake fluid
Checking brake fluid level
Th e brake fluid level c an be checked with a quick glance.
Fig . 22 6 En gin e
co mp art m ent : B ra ke
fl uid re servoir
Befo re yo u c heck anything in th e en gin e compar tme nt,
always read and heed all WARNINGS~ & in "Working in
the eng ine compartment" on
page 271 .
Read the brake fl uid level from the bra ke fluid reservoir
~ fig . 226. T he b rake fluid leve l must be betwee n the
" M IN " and "MAX" markings.
The brake fluid reservoir is located at the rear partition of the engine
compartment on the left side~
page 272 . .,_

_____________________________________________ C_h_ e_ c_k _in ~ g_ a_n _d_ f_il _li _n ~g __ _
•
The fluid level may drop slightly after some time due to the auto­
m atic adjustment of the brake pads. This is not cause for alarm .
If the brake fluid level fal ls
considerably below the "MIN" mark , the
brake warning/indicator light (U.S. models :
BRAKE, Canadian models:
{(j))) will come on=> page 16 and => page 29. Do not continue to
operate the vehic le. The complete brake system should be thor ­
oughly checked by an author ized Audi dealer or qualified workshop
and the cause corrected . If the brake fluid level is too low, the brak e
warning/ind ica tor light will illuminate. Contact an authorized Audi
dea ler
immediatel y.
[ i J Tip s
The brake fluid reservoir is located underneath the cover. •
Changing brake fluid
Have the brake fluid changed by an experienced techni ­
cian.
Brake fluid absorbs moisture from the air . If th e water content in the
brake fluid is too h igh, corrosion in the brake system may result
after a period of time. The boi ling point of the brake fluid will also
decrease considerably and decrease braking performance .
Therefore , the brake fluid must be changed
ev ery tw o ye ars. Always
use new brake fluid which conforms to Federa l Motor Veh ic le Stan ­
dard "FMVSS 116 DOT 4".
T he brake fluid res ervoir can b e difficul t to reach, therefore, we
recommend that you have the brake fluid changed by your autho ­
rized
Audi de ale r. Your dealer has the correct tools, the right brake
fluid and the know -how to do this fo r you .
& WARNING
• Brake f luid i s poi sonou s. It mu st b e stored on ly in the clo sed
o riginal cont aine r out of the r eac h of childr en!
& WARN ING (c ontinued )
• Brake f ailur e can re sult fr om old or inappropriate bra ke fluid .
Ob se rve these p recauti ons:
- Use on ly brake fl uid that meet s SAE specification
J 17 03 and
c on fo rm s to Feder al Mot or Vehicle Sta ndard 11 6. Always c heck
with your authorized Audi de ale r to m ake sur e you are u sing
th e c orre ct b rake flu id . T he cor re ct t ype of br ake fluid is als o
indi cated on the brake fluid r eservoir.
- The br ake f luid mu st be ne w. H eavy u se of the b rake s can
c au se a vapor lock if the brake fluid i s left in the system to o
long. Thi s c an seriou sly affe ct the effi ciency of the brake s as
well as your safety . This could re sult in an a ccid ent .
0 Note
Brake fluid will damage the paint of your vehicle .
ffi For the sake of the environment
Because of the problem of proper disposal of brake fluid as well as
the special too ls required and the necessary expertise, we recom­
mend that you have the brake fluid changed by your authorized Audi
dea ler .•
Battery
General information
Under normal operat ing conditions, the battery in your Audi does
not need any maintenance. With
high outside temperatures or long
daily drives we recommend that you have the electrolyte level
checked by an authorized Audi dealer or qualified workshop. The
e lectrolyte level should a lso be checked each time the battery is
charged
=> page 284 . ~
Vehicle care I t •

What do I do now? -__________________ __;__:....:....:..:: ___ J?rll
•
& WARNING (continued)
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed with the
folding chocks or other objects. When one front wheel is lifted off
the ground, placing the Automatic Transmission in "P" (Park) will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and firm.
If necessary, use a sturdy board under the jack.
• After installing the inflatable spare tire, make sure that you
replace the flat tire/wheel in its storage area properly and tighten
the knurled retaining screw securely.
0 Note
If you are changing the wheel on a steep incline, use a rock or
similar object to block the opposite wheel to prevent the vehicle
from moving.
[ i] Tips
Obey all laws.•
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and in exactly that order.
1. Remove the decorative wheel cover*. For more details
see also =>
page 314, "Decorative wheel covers".
2. Loosen the
wheel bolts=> page 315.
3. Locate the proper mounting point for the jack and align
the jack below that point=>
page 315.
4. Lift the car with the jack=> page 315.
5. Remove the wheel with the flat tire and then install the
spare tire=> page 317.
6. Tighten all wheel bolts lightly.
7.
Lower the vehicle with the jack.
8. Use the wheel bolt wrench and
firmly tighten all wheel
bolts in a crisscross pattern=>
page 315.
9. Replace the decorative wheel cover*.
_& WARNING
Always read and follow all WARNINGS and information => & in
"Raising the vehicle" on
page 315 and => page 318. •
After changing a wheel
A wheel change is not complete without the doing the
following.
- Store and secure the wheel you replaced in the spare
wheel well.
- Replace the tools and the jack in their proper location.
- Check the
tire pressure of the spare tire as soon as
possible.
- As soon as possible, have the
tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is 90 ft lbs. (120 Nml.
- Have the flat tire
replaced as soon as possible.
Do-it-yourself service

lllffll.,___W_ h_ a _ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
Fig. 244 Close-up:
proper positioning of
jack
The location of the jack point is indicated by an indentation
on the underside of the vehicle :::;,
page 315, fig. 243.
- Activate the
parking brake to prevent the vehicle from
rolling unintentionally.
Shift into
1st gear on vehicles with manual transmission
or move the selector lever to the
P position on vehicles
with automatic transmission*.
- Find the
lifting point in the sill that is closest to the faulty
wheel :::;,
page 315, fig. 243.
- Turn the handwheel on the
vehicle jack until the jaw
:::;, fig. 244 @ covers the
notch on the vehicle.
- Align the vehicle jack so the jaw @ covers the notch and
the base plate ® is flat on the floor. The base plate®
must be
vertical under the lifting point @.
Install the rod on the vehicle jack: Insert the rod into the
opening on the handwheel. Turn the rod left or right to
secure it.
- Continue raising the jack with the rod until the wheel lifts
off the ground slightly.
Only position the vehicle jack at the designated points~ page 315,
fig. 243. There is exactly one location for each wheel. Do not position
the jack in any other locations.
Soft ground under the jack can cause the vehicle to slip off the jack.
Always place the jack on firm ground. Use a flat, stable support if
necessary. Use a non -slip surface such as a rubber mat on a
slippery
surface
such as tile.
& WARNING
• You or your passengers could be injured while changing a
wheel if you do not follow these safety precautions:
-Positioning the jack under the vehicle at any other place than
those indicated above may damage the vehicle or may result in
personal injuries.
- A soft or unstable surface under the jack may cause the
vehicle to slip off the jack. Always provide a firm base for the
jack on the ground.
If necessary, use a sturdy board under the
jack.
- On hard, slippery surface (such as tiles) use a rubber mat or
similar to prevent the jack from slipping.
• To help prevent injury to yourself and your passengers:
- Do not raise the vehicle until you are sure the jack is securely
engaged.
- Passengers must not remain in the vehicle when it is jacked
up.
- Make sure that passengers wait
in a safe place away from
the vehicle and well away from the road and traffic.
- Make sure jack position is correct, adjust as necessary and
then continue to raise the jack. •

Fuses and bulbs -
------------------
No. Consumer
10 Climate control
11 Terminal 30 diagnostic connector
12 Steering column switch module Ampere
10
10
5
Fuse Location , Luggage Compartment right
Fig . 250 Fuse panel
layout
Read numbers of the fuses in the luggage compartment starting
from inside.
No. Consumer
Fuse panel B !black)
1 Luggage compartment lid control module
(Avant)
2 Trailer control module
3 Trailer control module
4 Trailer control module
5 Electromechanical parking brake
6 Electronic damping control Electromechanical parking brake Ampere
30
15
20
20
5
15
30
•
No. Consumer
8 Vehicle electrical system control module 2
9 quattro Sport
10 Vehicle electrical system control module 2
11 Vehicle electrical system control module
12 Terminal 30
Fuse panel C (brown)
1
2
3
4
5
6
7
8
9
Luggage compartment lid control module
Right front seat heating
DCDC converter path 1
DCDC converter path 2
Socket Not used
Electromechanical parking brake
Rear seat heating
Passenger side door control module
10 Not used
11 Passenger side door control module
12 Not used
Fuse panel D !red)
1 Rear center console outlet
2 Front center console outlet
3 Luggage compartment outlet
4 Cigarette lighter
6 Rear Seat Entertainment supply
Vehicle care Do-it-yourself service
Ampere
30
35
30
20 5
30 15
40
40
30
30
30
30
15
15
15 15
15
5
5
Technical data