2010 ASTON MARTIN V8 VANTAGE heater

Seating (01.10)
Body System (01.00)1-7-4 Workshop Manual Issue 4, November 2008
Removal
1. Remove 6 way height adjust er (see Workshop Manual
procedure 01.10.AE 6 Way Height Adjuster - Including
Motors - Renew).
2. Remove screws (x3) heater and lumbar switch assembly
(see Figure 1).
3. Release switch assembly and disconnect multiplug
4. Release cover from cushion frame assembly (see Figure 2). 5. Pull seat cushion cover from between squab and
cushion frames and remove cover (see Figure 3).
Installation
1. Connect multiplugs (x2) heater and lumber switch assembly.
2. Install switch assembly to seat
3. Ease cover over cushion foam attach to velcro.
4. Push cushion flap between cushion and squab and secure to cushion frame assembly.
5. Secure cushion cover to sides and front edge of seat cushion frame assembly.
6. Install 6 way height adjust er (see Workshop Manual
procedure 01.10.AE 6 Way He ight Adjuster - Including
Motors - Renew).
6-Way Height Adjuster (Inc. Motors) -
Renew
Removal
1. Power seat fully forward.
2. Remove bolts (x2) securing rear of seat to seat rails.
3. Power seat fully rearwards.
4. Remove bolts (x2) securing front of seat to seat rails.
5. Battery isolation switch ‘OFF’.
6. Remove bolt securing seat belt to seat frame.
7. Tip the seat forwards and disconnect multiplugs (x4).
8. With assistance, remove seat assembly.
9. Remove screw (x1) relay to seat cushion base.
Figure 1
Figure 2
A0110287
A0110288
Figure 3
Repair Operation Time (ROT)
ItemCode
6-Way Height Adjuster-Renew 01.10.AE
A0110290

Seating (01.10)
Body System (01.00)1-7-6 Workshop Manual Issue 4, November 2008
16. Slide 6 way height adjuster to release and remove adjuster from seat assembly (see Figure 5).
Installation
1. Install relay to seat cushion base.
2. Connect multiplugs (x3) and secure to 6 way adjuster frame.
3. Secure seat belt buckle harness (cable ties x4) to 6 way seat adjuster frame assembly.
4. Install a new bolt that attaches the seat belt buckle.
5. Position 6 way height adju ster to seat cushion frame
assembly and install screws (x4).
6. With assistance, install seat in the vehicle.
7. Position seat belt to seat frame, install and torque tighten bolt.
8. Tip seat forwards and connect multiplugs (x4).
9. Position seat onto seat rails.
10. Battery isolation switch ‘ON’.
11. Install front bolts (x2), Power seat forward and install rear bolts (x2). Torque tighten bolts (x 4).
Squab Motor Kit - Renew
Removal
1. Remove squab cover (see Workshop Manual procedure 01.10.AC Cover Assembly - Front Seat Squab - Each -
Renew). 2. Disconnect heater multiplug and remove squab foam
(see Figure 1).
3. Release top mountings of lumbar adjust frame and move to access squab motor (see Figure 2).
Figure 5
Repair Operation Time (ROT)
A0110292
Figure 1
Figure 2
A0110293
A0110282

Seating (01.10)
Body System (01.00)
Issue 4, November 2008 Workshop Manual 1-7-7
4. Remove clip from adjust rod and pull through to clear motor (see Figure 3).
5. Remove motor from seat fr ame (bolt x1 and multiplug
x1). (see Figure 4)
Installation
1. Install motor to seat frame, push adjust rod through motor (key splined) and install clip.
2. Position motor and install bolt (x1) and multiplug (x1).
3. Install top mountings of lumbar adjust frame.
4. Connect heater multiplug and install squab foam.
5. Install squab cover (see Workshop Manual procedure 01.10.AC Cover Assembly - Front Seat Squab - Each -
Renew).
Lumbar Support Kit - Renew
Removal
1. Remove squab cover (see Workshop Manual procedure 01.10.AC Cover Assembly - Front Seat Squab - Each -
Renew).
2. Disconnect heater multiplug and remove squab foam (see Figure 1).
3. Remove seat back shell (rivets x4) (see Figure 2).
Figure 3
Figure 4
A0110289B
A0110302
Repair Operation Time (ROT)
A0110293
A0110285

Seating (01.10)
Body System (01.00)1-7-8 Workshop Manual Issue 4, November 2008
4. Disconnect lumbar motor multiplug (see Figure 3).
5. Remove lumbar support fr om seat frame (screws x2)
(see Figure4).
Installation
1. Install lumbar support to seat frame (screws x2).
2. Connect lumbar motor multiplug.
3. Install seat back shell (rivets x4).
4. Connect heater multiplug and install squab foam.
5. Install squab cover (see Workshop Manual procedure 01.10.AC Cover Assembly - Front Seat Squab - Each -
Renew).
Side Airbag - Renew
Removal
1. Remove seat (see Workshop Manual procedure 01.10.AB Seat Assembly - Front - LH - Remove for
Access and Refit).
2. Remove lever cover (manoeuvre over lever).
3. Disconnect airbag multiplu g and release from bracket
(see Figure 1).
4. Remove fixing multiplug br acket, move aside (see Figure
2).
5. Remove (slide down) airbag module (bolt x1).
Installation
1. Install airbag module (bolt x1) (torque).
2. Install multiplug bracket fixing.
3. Connect airbag multiplug and secure to bracket.
4. Install lever cover (manoeuvre over lever).
5. Install seat (see Workshop Manual procedure 01.10.AB
Seat Assembly - Front - LH - Remove for Access and
Refit).
Figure 3
Figure 4
Repair Operation Time (ROT)
A0110284
A0110284A
Figure 1
Figure 2
A0110281
A0110281A

Seating (01.10)
Body System (01.00)
Issue 4, November 2008 Workshop Manual 1-7-9
Front Seat Buckle Assembly - Renew
Removal
1. Power seat fully forward.
2. Remove bolts (x2) securing rear of seat to seat rails.
3. Power seat fully rearwards.
4. Remove bolts (x2) securing front of seat to seat rails.
5. Battery isolation switch ‘OFF’.
6. Remove bolt securing seat belt to seat frame.
7. Tip the seat forwards and disconnect multiplugs (x4).
8. With assistance, remove seat assembly.
9. Release multiplug (x1) seat belt buckle harness to 6 way
seat adjuster frame assembly.
10. Release cable ties (x4) securing seat belt buckle harness to 6 way seat adjuster frame assembly (see Figure 1). 11. Remove bolt (x1) seat belt buckle to frame (see Figure
2).
12. Remove seat belt buckle assembly.
Installation
1. Secure harness and multiplug to 6 way seat adjuster frame assembly.
2. Install seat belt buckle.
3. With assistance, install seat in the vehicle.
4. Position seat belt to seat frame, install and torque tighten bolt.
5. Tip seat forwards and connect multiplugs (x4).
6. Position seat onto seat rails.
7. Battery isolation switch ‘ON’.
8. Install front bolts (x2), Power seat forward and install rear bolts (x2). Torque tighten bolts (x 4).
Valance Heater and Lumbar Switch
Assembly - Renew
Removal
1. Power seat fully forward.
2. Remove bolts (x2) securing rear of seat to seat rails.
3. Power seat fully rearwards.
4. Remove bolts (x2) securing front of seat to seat rails.
5. Disconnect vehicle battery.
Repair Operation Time (ROT)
A0110289B
Figure 2
Repair Operation Time (ROT)
A0110287A

Seating (01.10)
Body System (01.00)1-7-10 Workshop Manual Issue 4, November 2008
6. Tip the seat backwards and remove screws (x3) heater and lumbar switch assembly to seat (see Figure 1).
7. Release switch assembly from seat.
8. Disconnect multiplug (x2) and remove switch assembly (see Figure 2).
Installation
1. Connect multiplugs (x2) switch assembly.
2. Install switch assembly (screws x3).
3. Position seat onto seat rails.
4. Connect vehicle battery
5. Install front bolts (x2), Power seat forward and install rear bolts (x2). Torque tighten bolts (x 4).
Seat Harness Kit - Renew
Removal
1. Remove seat 6 way height adjuster (see Workshop Manual procedure 01.10.AE 6 Way Height Adjuster -
Inc. Motors - Renew). 2. Remove release lever (see Figure 1).
3. Remove lever cover (see Figure 2).
4. Disconnect airbag multiplu
g and release from bracket
(see Figure 3).
Figure 1
Figure 2
Repair Operation Time (ROT)
A0110287
A0110286
Figure 1
Figure 2
Figure 3
A0110296
A0110296A
A0110281

Seating (01.10)
Body System (01.00)
Issue 4, November 2008 Workshop Manual 1-7-11
5. Remove fixing multiplug bracket, move aside.
6. Remove (slide down) airbag module (bolt x1).
7. Release cover from seat back shell (studs x2 velcrox2).
8. Release cover from seat back shell (strip x2 /clips x9).
9. Release cover from bottom of seat back shell.
10. Push cover through to front of seat, release strip and ease from foam (velcro strips).
11. Disconnect heater multip lug and remove squab foam
(see Figure 4).
12. Remove seat back shell (rivets x4) (see Figure 5). 13. Disconnect lumbar and sq
uab motor multiplugs (see
Figure 6).
14. Remove earth header (nut and bolt) and release harness from clips (x2) (see Figure 7).
Figure 4
Figure 5
A0110293
A0110285
Figure 6
Figure 7
A0110284
A0110295

Seating (01.10)
Body System (01.00)1-7-12 Workshop Manual Issue 4, November 2008
15. Drill out pop rivets from release rod support, and feed harness past rod (see Figure 8).
16. Release harness from clips (x3) and seat cover loop, feed through seat frame (see Figure 9). 17. Disconnect cushion heater
multiplug (see Figure 10).
18. Release cushion cover from frame, feed harness through cover and foam (see Figure 11).
Installation
1. Feed harness through cushion cover and foam, secure cover to frame,
2. Connect cushion heater multiplug.
3. Feed harness through seat frame, secure to clips (x3) and seat cover loop.
4. Feed harness past rod and install pop rivets to release rod support.
5. Install earth header (nut and bolt) and secure harness to clips (x2).
6. Connect lumbar and squab motor multiplugs.
7. Install seat back shell (rivets x4).
8. Connect heater multiplug and install squab foam.
9. Ease cover over foam attach to velcro, secure strip and push through seat.
10. Secure cover to seat back shell.
Figure 8
Figure 9
A0110295A
A0110294
Figure 10
Figure 11
A0110294A
A0110294B