Welcome
0-0-6 Workshop Manual Issue 5, January 2010
Welcome
This Workshop Manual is part of a suite of technical manuals
provided for V8 Vantage. Other technical manuals include:
• Parts manual
• OBDII Diagnostic manual
• Man hour schedules
Chapters
Each chapter in this workshop manual is associated with a 4
digit number, i.e. Transmission (07.00). Each chapter is then
further broken into sections, i.e. Automatic Transmission
(07.01).
Chapter Navigation
Example 1:
Older workshop manuals would have Steering and
Suspension together in one chapter. The structure now used
places Steering and Suspension into their own chapters.
When required references are made out to other chapters.
Page Numbering
The page numbering system used within this workshop
manual is as follows:
Systems Classification Coding
Alongside the ‘System’ and ‘Sub system’ section titles appear
codes. For example Exhaust ‘ 09.00’ or Power Steering
‘ 11.02 ’. These codes relate to a Corporate Product Systems
Classification (CPSC) and are designed to segregate the parts
for engineering release and organise a variety of engineering
data.
Special Tools
Where special service tools are required to perform an
operation, the tool number is recorded at the point of use
within the procedure. Where the operation of a special
service tool is complicated or not obvious, refer to Appendix
and Glossary for detailed operation procedures. A pictorial
list of special service tools available for this vehicle can also
be found in Appendix and Glossary.
Location References
References to left, right, front or rear of the vehicle or of a
component are referenced from sitting in the drivers seat
facing forward. Any such refe rences to assemblies removed
from the vehicle are to the normal orientation of the
assembly when installed in the vehicle.
The following Warnings, Cautions and Notes are used within
this Owner’s Guide to call your attention to specific types of
information.
Warnings, Cautions and Notes
Warnings
Cautions
Notes
Repairs and Replacements
Where replacement parts are required, it is essential that
only genuine Aston Martin parts are used. Your attention is
drawn to the following points concerning repairs and the
fitting of genuine Aston Martin parts and accessories:
• Safety features embodied in the vehicle may be impaired if other than genuine Aston Martin parts are installed. In
certain territories, legislation prohibits the fitting of parts
which are not produced to the manufacturers
specification
• Adhere to torque wrench settings given in this manual
• Locking devices, where specified, must be installed. If the efficiency of a locking device is impaired during removal,
it must be renewed
• The vehicle warranty may be invalidated by the installation of other than genuine Aston Martin parts
3- 2- 5
System, i.e. Engine system
Subsystem, i.e. Engine lubrication system
Page Number, i.e. Number within subsystem
WAR NI NG
IDENTIFIES PROCEDURES WHICH MUST BE
FOLLOWED PRECISELY TO HELP AVOID THE RISK OF PERSONAL INJURY.
Caution
Provided to indicate procedur es which must be followed
precisely to reduce the possibility of damage to the vehicle.
Provided to indicate procedur es which will help to avoid
difficulties in the oper ation of the vehicle.
Service Bulletin SB-17-0298
February 2009 Page 5 of 5
Warranty Data
DBS and DB9, Coupe and Volante
Description Time Allowed Labour Code
Headlamp Condensation Drying Procedure – The
two sides 0.9 hrs. 17.01.BG
Headlamp Condensation Drying Procedure – One
Side 0.45 hrs. 17.01.BH
Vantage Coupe and Roadster
Description Time Allowed Labour Code
Headlamp Condensation Drying
Procedure – The two sides. 1.0 hrs. 17.01.BG
Headlamp Condensation Drying
Procedure – One Side 0.5 hrs. 17.01.BH
If you have any queries related to th
is Service Bulletin, please contact: Aston Martin Technical Services on:
+44 (0) 1926 644720 or facsimile: +44 (0) 1926 644733.
E-mail: [email protected]
. Or contact your After Sales Manager.
The English version of this Service Bulletin is written in Simplified Technical English to ASD STE-100™.
Service Bulletin SB0286V2
December 2009 Page 5 of 5
Figure 9
Figure 10
Parts Data
Description Part Number Quantity
Battery Vent Tube 1R12-372635-AA 1
Adhesive Sealing Patch 4G43-L20220-AA 1
Warranty Data
DB9 Coupe and Volante
Description Time Allowed Labour Code
Rear Lamp Unit – Left Side - Drying
Procedure 0.8 17.03.AC
Rear Lamp Unit – Right Side -
Drying Procedure 0.8 17.03.AD
V8 Vantage and Roadster
Description Time Allowed Labour Code
Rear Lamp Unit – Le
ft Side - Drying
Procedure 0.65 17.03.AC
Rear Lamp Unit – Right Side -
Drying Procedure 0.70 17.03.AD
DBS
Description Time Allowed Labour Code
Rear Lamp Unit – Le
ft Side - Drying
Procedure 0.8 17.03.AC
Rear Lamp Unit – Right Side -
Drying Procedure 0.8 17.03.AD
A
B
If you have any queries related to th
is Service Bulletin, please contact: Aston Martin Technical Services on:
+44 (0) 1926 644720 or facsimile: +44 (0) 1926 644733.
E-mail: [email protected]
. Or contact your After Sales Manager.
The English version of this Service Bulletin is written in Simplified Technical English to ASD STE-100™.
