2010 ASTON MARTIN V8 VANTAGE coolant

Aston Martin V8 Vantage 2009 MY EOBD DocumentationAston Martin/Ford Confidential
Component/ System Fault Code Monitor Strategy
Description Malfunction Criteria Threshold Parameter Secondary Parameters Entry Parameters Time Required DTC
StorageMIL Illumin-
ation
Sensor input < 0.2 volts 132.8degC
(271.1degF) or
> 4.9 volts
-41.2degC(-42.1degF)
Time with sensor input out
of range > 5.0 sec
Sensor input < 0.2 volts 132.8degC
(271.1degF)
Time with sensor input out
of range > 5.0 sec
Sensor input > 4.9 volts
-41.2degC(-42.1degF)
Time with sensor input out
of range > 5.0 sec
Engine off time >360minutes
ECU power up timer >0.1seconds
Sensor input stuck 103 +/- 59 kPa
Large control error > +/-103 kPa (> 15 psig)
Time with sensor input out
of range > 8.0 sec
(Demand - sensed) error
too large > 137 kPa
(20 psig)Demand pressure within
limits < 413 kPa or > 344 kPa
(< 60 psig or > 50 psig)
Time with sensor input out
of range > 8 sec
Fuel level above minimum
level > 0.15 * 100 %
Sensor input < 0.95 volts 174.23kPa
(25.33psig)
Time with sensor input out > 8 sec
Sensor input > 4.88 volts 647kPa
(93.95psig)
Time with sensor input out > 8 sec
P1233 Fuel pump driver module Time with failure > 5.0 seconds
P1235 Fuel pump control out of Time with failure > 5.0 seconds
P1237 Fuel pump circuit malfunction Time with failure > 5.0 seconds 1 = malfunction Battery voltage> 11.0 volts
Engine coolant temp < 116 deg C (< 240 deg F)
Intake air temp <66 deg C
(< 150 deg F)
Engine rpm (Used to
determine crank mode) > FN384 rpm
(See Function)None
Number of CKP edges
incorrect, missing tooth in
unexpected location. SW
loses synchronization with
missing tooth location None
Increment fault counter by
10 on each event. Set
code when counter
exceeds 100
Engine Speed >550rpm
<5000rpm
Increment fault counter by
2 on each event. Set code
when counter exceeds 50 N/A
Engine speed >550 rpm
<2200rpm
Increment fault counter by
2 on each event. Set code
when counter exceeds 50 N/A
Engine speed >550 rpm
<2200rpm Footnote a) Footnote c)
Continuous
<> +/-12.3degC
(54.1degF) Once per driving
cycle
Fuel Temperature
Sensor Input
ECT-Fuel rail temperature
Circuit Malfunction - range
check
Circuit Malfunction - range
check
Circuit Malfunction - range
check
P0180
P0182 (Low)
P0181 Rationality check
P0183 (High)
Ignition System- CKP
Circuit Malfunction P0320 Intermittent/Noisy CKP signal
check Footnote c)
Footnote c)
Ratio of PIP events to CID
events Continuous Footnote a) Footnote c)
n to 1 (To pass test)
n to 1 (To pass test)
Increment fault counter
by 1 on each event.
Set code when counter
exceeds 40
(> 8 sec @ 600rpm)
Smart power driver status
P0340 (BankA)
P0345 (BankB) Circuit continuity check, open
or shorted
P0201
P0202 P0203
P0203 P0204
P0205 P0206
P0207 P0208
Camshaft Position
Input Rationality check
Rationality checkRatio of PIP events to CID
events Continuous
Footnote a)
Footnote c)
Continuous Footnote a) Footnote c) Footnote a)
Battery Voltage 11< Voltage <18
11< Voltage <18 Continuous Footnote a) Footnote c)
11< Voltage <18
Circuit malfunction
Battery Voltage
Battery Voltage
Range check
Continuous Footnote a)
Fuel Injectors
Fuel Rail Pressure
Input
P0190
P0191
P0192 (Low)
P0193 (High)
Fuel Pump Range check
Range/Performance check
11

Aston Martin V8 Vantage 2009 MY EOBD DocumentationAston Martin/Ford Confidential
Component/ System Fault Code Monitor Strategy
Description Malfunction Criteria Threshold Parameter Secondary Parameters Entry Parameters Time Required DTC
StorageMIL Illumin-
ation
Ratio of PIP events to
spark events seen 1 to 1 (To pass test) Increment fault counter by
20 on each event. Set
code when counter
exceeds 200 N/A
PCM able to determine
coil Yes
Above neutral torque axis See RPM/Load Table FNMISOK_97: Monitor
disabled when less than
0.5
Difference between actual
and desired rpm > -200 rpm
Engine coolant temp -40 deg C
(> -40 deg F)
Time with solenoid at limit > 5 sec Time since engine start > 60 sec
Fuel control Closed loop
Idle state At idle
Difference between actual
and desired rpm > 100 rpm
Engine coolant temp -40 deg C
(> -40 deg F)
Time with solenoid at limit > 5 sec Time since engine start > 60 sec
Fuel control Closed loop
Idle state At idle
Vehicle ID block not
programmed P1639 VID block not programmed
with tire/axle ratio Time with error present > 0 sec
NoneNoneContinuous Footnote a) Footnote c)
VID Block checksum P0602 VID block checksum test failedTime with error present > 0 sec
NoneNoneContinuous
KAM Failed / reset P0603 Keep Alive Memory check failed / memory was resetTime with error present > 0 sec
NoneNoneContinuous Footnote a) Footnote c)
RAM memory failed P0604 Random Access Memory test has failed.Time with error present > 0 sec
NoneNoneContinuous Footnote a) Footnote c)
ROM checksum test
failed P0605 Read Only Memory test failed Time with error present > 0 sec
NoneNoneContinuous Footnote a) Footnote c)
CPU Fault detected P0607 General fault with the CPU has been detectedTime with error present > 0 sec
NoneNoneContinuous
Keep Alive Memory
Power Input P1633 KAM power input voltage too
low/open circuit Time with error present > 20 sec
NoneNoneContinuous Footnote k) Footnote i)
Vehicle Speed
Sensor P0500 Invalid / missing data from
BCM BCM reports VSS failure
OR no data on CAN bus1
Time after start >2 secondsContinuous Footnote a) Footnote c)
Commanded duty cycle on
or full-off >=0.5 * 100 % or = 0%
Signal circuit voltage Refer to Appendix for threshold calculation
Time with circuit
malfunction > 5 sec
P0330 Bank1
Sensor1 Sensor range check
Engine speed>1000rpm
P0325 Bank1
Sensor2 Sensor range check
Engine coolant temp >55degC (131degF)
P130A Bank2
Sensor2 Sensor range check
P130B Bank2
Sensor2 Sensor range check
P0460 (Range
Check) Sensor range check
Sensor input <= 7 or >= 254 A/D
counts w/in a range of
256 A/D counts
P0462 (Low) Circuit Check Sensor input< 7 A/D counts
P0463 (High) Circuit Check Sensor input> 254 A/D counts
Time with sensor out of
range > 30 sec
Sensor rationality check
(Stuck sensor) Compare fuel mass
consumed versus
observed change in gauge
readings (Min. and max.
reading) Fuel consumed (Fuel
consumed and fuel gauge
reading range are both
stored in KAM and reset
after a refuelling event or
DTC storage)> 10 %
"Fuel consumed" is
continuously calculated based
on PCM fuel pulse width
summation as a percent of
fuel tank capacity Fuel consumed (%) -
Range of fuel gauge
readings (%)
> 0.125 * 100 %
threshold at fuel tank
fill from 15% to 85%
Fuel consumed (%) -
Range of fuel gauge
readings (%) > 0.054 + 0.125 * 100
% threshold if tank
overfilled (> 85%)
Fuel consumed (%) -
Range of fuel gauge
readings (%) > 0.175 + 0.125 * 100
% threshold if tank on
reserve (< 15%)
Change in fuel level > 0.1925*100% Fuel level on the data bus N/A
Number of intermittent
events > 5
I/M Readiness Number of driving cycles
to clear I/M readiness flag
at extreme ambient
conditions > 1 driving cycle(s) Footnote e)
Footnote a)
Footnote c)
Footnote a) Footnote j) Footnote e)
Fuel Level Input
Noisy Continuous Footnote a)
Continuous Footnote a)
P0461
(Rationality) Sensor rationality check
(Noisy sensor)
Fuel Level Input
Stuck
P0460
(Rationality) Continuous
N/A Continuous
Calculated sensor noise
(peak to peak variation)
>0.25
KNKS Sensor
Fuel Level Input Out
Of Range NoneFootnote a) Footnote e)
Vapor Management
Valve Circuit
Malfunction P0443 Circuit continuity test, open or
shorted None
N/A Continuous
11.5< Voltage
Ignition System-
Ignition Coil Primary
Circuit Malfunction
IAC Solenoid
Underspeed Error P0507
P0506
Functional check -
overspeed error
Functional check -
underspeed error
IAC Solenoid
Overspeed Error
Footnote a) Footnote c)
Continuous
P0351
P0352
P0353
P0354
P0355
P0356
P0357
P0358
Rationality check
Continuous Footnote a) Footnote c)
Battery Voltage
12

Aston Martin V8 Vantage 2009 MY EOBD DocumentationAston Martin/Ford Confidential
Component/ System Fault Code Monitor Strategy
Description Malfunction Criteria Threshold Parameter Secondary Parameters Entry Parameters Time Required DTC
StorageMIL Illumin-
ation
TPPC chip failure in
PCM P0606 TPPC chip to CPU
communication fault Number of attempts > 1
Continuous Footnote a) Footnote c)
Engine rpm > 1000 rpmEngine coolant temp > 15 deg C
(> 60 deg F)Continuous Footnote a) Footnote c)
Sensor signal voltage < 1.22 volts or > 3.42 volts
Engine load > 0.7 * 100% or < 0.2 *
100%
Time with sensor out of
range > 3.0 sec
Time with low throttle
voltage at TPPC or PCM >= 0.176 seconds
Sensor signal voltage < 0.2 volts
Time with high throttle
voltage at TPPC or PCM >= 0.176 seconds
Sensor signal voltage > 4.87 volts
Time with low throttle
voltage at TPPC or PCM >= 0.176 seconds
Sensor signal voltage < 0.08 volts
Time with high throttle
voltage at TPPC or PCM >= 0.176 seconds
Sensor signal voltage > 4.80 volts
Time with correlation
failure from the TPPC or
PCM or Equizzer >= 240 sec
Magnitude of the
difference of the relative
readings of the sensor
signal voltage > 0.073 volts
(6.533deg)
P2104 ETC FMEM – forced idle Two or three pedal sensors failed, throttle
plate stuck>= 100 to 400 msec None
N/AContinuous Footnote a) Footnote c)
P2105 ETC FMEM – forced engine shutdown Equizzer detected fault >= 16 to 960 msec None
N/AContinuous Footnote a) Footnote c)
P2106 ETC FMEM – pedal-follower mode Sensor fault: MAF, one
TP, CKP, TSS, OSS, stuck
throttle, throttle actuator
circuit fault>= 16 to 960 msec None
N/AContinuous Footnote a) Footnote c)
P2110 ETC FMEM – default throttle angle Two TPs failed; TPPC
detected fault>= 600 to 800 msec None
N/AContinuous Footnote a) Footnote c)
P2111
(Stuck Open) Functional test
Desired throttle angle vs.
actual throttle angle
measured in a rolling
average routine during
throttle tip-in> 3.5 degrees None
N/AContinuous Footnote a) Footnote c)
P2112
(Stuck Closed) Functional test
Desired throttle angle vs.
actual throttle angle
measured in a rolling
average routine during
throttle tip-out> 3.5 degrees None
N/AContinuous Footnote a) Footnote c)
P2107 TPPC processor check Internal processor test, lost communication with
main CPU>= 60 msec None N/A Continuous Footnote a) Footnote c)
P2100 Circuit check Throttle actuator circuit open>= 1750 msec None N/A Continuous Footnote a) Footnote c)
P2101 Range check Throttle actuator range/performance test,
throttle plate angle does
not followed commanded
angle>= 500 msec None N/A Continuous Footnote a) Footnote c)Electronic Throttle Control
Rationality check
None
TP Sensor
Inconsistent With
MAF Sensor
TP Sensor A/B
Correlation
TP Sensor 'B' Input
Out Of Range P0122 (Low)
P0123 (High)
Range check
Rationality check vs. MAF
input
Throttle Actuator
Control System
Throttle Plate
Position Controller
(TPPC)
Throttle Actuator
Control Motor P2135
N/AContinuous Footnote a) Footnote c) Footnote c)
None
P0222 (Low) Range check N/AContinuous Footnote a)
P0223 (High)
TP Sensor 'A' Input
Out Of Range
None
N/A Continuous Footnote a) Footnote c)
P0068
13

Aston Martin V12 Family
2009 MY V12 Family EOBDincl. V12 Vantage
Aston Martin/Ford Confidential
Component/ System Fault Code Monitor Strategy
Description Malfunction Criteria Threshold Parameter Secondary Parameters Entry Parameters Time Required DTC
StorageMIL Illumin-
ation
P0420
(Bank 1) HC efficiency inferred from
oxygen storage capacity Rear/Front HO2S switch
ratio> 0.76 (Unitless) Engine coolant temp and
ECT sensor OK
(P0117/0118) 65C < Engine coolant
< 110C (150 - 230F)
Once per driving
cycleFootnote a) Footnote c)
P0430
(Bank 2) HC efficiency inferred from
oxygen storage capacity Rear/Front HO2S switch
ratio>0.76 (Unitless) Intake air temp and IAT
sensor OK (P0112/0113) -7C < Inlet Air Tmp
< 82C (20-180F) Approximately 900
sec
Minimum time since start
to run Catalyst Monitor 60 sec
Air mass range cell 1 HO2S11 switches : 200 HO2S21 switches: 200 3.78 - 11.3 g/s
(0.5-1.5 lb/min)
Air mass range cell 2 HO2S11 switches : 200 HO2S21 switches: 200 11.3 - 18.9 g/sec
(1.5-2.5 lb/min)
Air mass range cell 3 HO2S11 switches : 200 HO2S21 switches:
FEGO2_MX_CT3 18.9 - 26.5 g/s
(2.5-3.5 lb/min)
Maximum number of
HO2S11 (Bank 1 front)
switches to allow monitor
completion 300
Maximum number of
HO2S21 (Bank 2 front)
switches to allow monitor
completion 300
Load range for air
mass cell 1 HO2S11 switches : 200
HO2S21 switches: 200 0.1 * 100 % - 1.0 * 100 %
Load range for air
mass cell 2 HO2S11 switches : 200
HO2S21 switches: 200 0.1 * 100 % - 1.0 * 100 %
Load range for air
mass cell 3 HO2S11 switches : 200
HO2S21 switches: 200 0.1 * 100 % - 1.0 * 100 %
Rpm range for air
mass cell 1 HO2S11 switches : 200
HO2S21 switches: 200 0 - 4000 rpmCatalyst Efficiency MonitorCatalyst System
Efficiency Below
Threshold
(Index Monitor)
1

Aston Martin V12 Family
2009 MY V12 Family EOBDincl. V12 Vantage
Aston Martin/Ford Confidential
Component/ System Fault Code Monitor Strategy
Description Malfunction Criteria Threshold Parameter Secondary Parameters Entry Parameters Time Required DTC
StorageMIL Illumin-
ation
P0300
to
P0312 Deviations in crankshaft
acceleration processed by
Neural Network Misfire
Monitor software and Catalyst
Temperature model Percentage misfire
required to exceed
Catalyst Damage
Temperature 900 deg c
(1650 deg F) catalyst
damage threshold, per
engine bank Type A: See RPM/Load
Table FNMISPCT_97 %
Type A:
200 revs
(Continuous)Type A:
Footnote b)
Type A:
Footnote d)
Full-range misfire capability Percentage misfire required to exceed
emission thresholdsType B: > 0.01 * 100
%
Type B:
1000 revs
(Continuous)Type B/C:
Footnote a)
Type B:
Footnote c)
Percentage misfire
required to clear emission
pending code < 0.001 * 100 % Time since engine start,
value based on time and
IAT 0 + FNMISACT sec
(See Transfer Functions)
Full-range misfire redline:
6900 rpm Time since PCM power up 0 sec
Time for NNMM
computation queue to fill4 revs from initial crank
(Meets 2 rev start delay
requirement)
Engine coolant temp -7 - 121 deg C ( 20 - 250 deg )
Engine rpm 500 - 4000rpm
Engine rpm in neutral
(Auto trans. only) < 3100 rpm
Net engine torque > -68 Nm ( -50 ft lbs)
Engine torque rate of
change > -34 Nm/s or < 41 Nm/s
(> -25 ft lbs/sec or
< 30 ft lbs/sec)
Throttle position rate of
change > -20 volts/background
loop or
< 30 * 5/1024
volts/background loop
Closed throttle
deceleration
(Dashpot mode) Closed throttle,
vehicle speed < 4 mph,
dashpot airflow adder
present
Engine rpm/load range See RPM/Load Table FNMISOK_97: Monitor
disabled when less than
0.5
Crankshaft position circuit
(PIP) OK (P0320)
Fuel shutoff for rpm or
vehicle speed limiting No fuel cutoff occurring
Fuel level > 0.15 * 100 %
Cylinder Misfire
Detected
Misfire Monitor
3

Aston Martin V12 Family
2009 MY V12 Family EOBDincl. V12 Vantage
Aston Martin/Ford Confidential
Component/ System Fault Code Monitor Strategy
Description Malfunction Criteria Threshold Parameter Secondary Parameters Entry Parameters Time Required DTC
StorageMIL Illumin-
ationStream 1 (Front) O2
Sensor Signal Stuck
Lean P2195
(Bank 1,
Sensor 1)Lack of HO2S switches
Stage 1:
(Look for short term fuel
trim stuck) Fuel control Closed loop or
Closed loop desiredContinuous Footnote a) Footnote c)
P2197
(Bank 2,
Sensor 1) Short term fuel trim > 1 + 0.3 * 100% Intake air temp sensor OK
(P0112/0113)
Time with short term fuel
trim at limit > 22 * 2 sec Engine coolant temp
sensor OK (P0117/0118)
Stage 2:
(Look for HO2S stuck at
startu
p)
Mass Air Flow sensor OK
(P0102/0103)
Cumulative time in test
mode since start up > 30 sec Throttle Position Sensor
OK (P0122/0123)
Number of switches since
start up < 4
Fuel tank pressure low
enough and sensor OK
(P0451, P0452, P0453) < 2,491 Pa
(< 10 in H2O)
Fuel control In FMEM at start up Fuel level above minimum
level > 0.15 * 100 %
Stuck sensor recovery
efforts failed
Time entry conditions hav
e
been present > 10 sec
Stream 1 (Front) O2
Sensor Signal Stuck
Rich P2196
(Bank 1,
Sensor 1)Lack of HO2S switches
Stage 1:
(Look for short term fuel
trim stuck) Fuel control
Closed loop or
Closed loop desired Continuous Footnote a) Footnote c)
P2198
(Bank 2,
Sensor 1) Short term fuel trim < 1 - 0.3 * 100% Intake air temp sensor OK
(P0112/0113)
Time with short term fuel
trim at limit > 22 * 2 sec. Engine coolant temp
sensor OK (P0117/0118)
Stage 2:
(Look for HO2S stuck at
startu
p)
Mass Air Flow sensor OK
(P0102/0103)
Cumulative time in test
mode since start up > 30 sec Throttle Position Sensor
OK (P0122/0123)
Number of switches since
start up < 4
Fuel tank pressure low
enough and sensor OK
(P0451, P0452, P0453) < 2,491 Pa
(< 10 in H2O)
Fuel control In FMEM at start up Fuel level above minimum
level > 0.15 * 100 %
Stuck sensor recovery efforts failedTime entry conditions hav
e
been present > 10 sec
HO2S Monitor
5

Aston Martin V12 Family
2009 MY V12 Family EOBDincl. V12 Vantage
Aston Martin/Ford Confidential
Component/ System Fault Code Monitor Strategy
Description Malfunction Criteria Threshold Parameter Secondary Parameters Entry Parameters Time Required DTC
StorageMIL Illumin-
ationStream 1 (Front)
HO2S Circuit Slow
Response P0133
(Bank 1)
Monitor HO2S switching
frequency and amplitude
(Forced at 1.5 Hz fixed rate) Switching frequency
(Indicates gross failure)
< 0.0 Hz Time since entering close
d
loop fuel control> 10 sec < 4 sec once per
driving cycleFootnote a) Footnote c)
P0153
(Bank 2) Switching frequency
difference from desired
(Test run at correct
frequency)< 0.19 Hz
Short term fuel trim 0.9 - 1.1 * 100 %
Signal voltage amplitude < 0.55 volts Engine coolant temp and
ECT sensor OK
(P0117/0118) 55 - 116 deg C
(130 - 240 deg F)
Fuel level above minimum
level > 0.15 * 100 %
Intake air temp and IAT
sensor OK (P0112/0113) < 71 deg C
(< 160 deg F)
Engine load and MAF
sensor OK (P0102/0103) 0.15 - 0.4 * 100 %
Vehicle speed and
VSS (P0500) or
OSS (P0720) sensor OK 30 - 60 mph
Engine rpm and
crankshaft position circuit
(PIP) OK (P0230) 1000 - 2200 rpm
Throttle position sensor
OK (P0122/0123)
Camshaft ID circuit (CMP)
OK (P0340)
No Misfire Monitor DTCs
Fuel rail pressure sensor
OK (P0190/0192/0193)
Flex fuel composition not
changing
Not transitioning into/out o
f
Characteristic Shift Down
Not in Phase 0 of Evap
Monitor
No Purge System reset
Maximum change in
engine rpm while running
monitor < 160 rpm
Maximum change in
engine load while running
monitor < 0.13 * 100%
Maximum change in
vehicle speed while
running monitor < 2.0 mph
Maximum change in short
term fuel trim while
running monitor (PTEC
only) < 0.1
6

Aston Martin V12 Family
2009 MY V12 Family EOBDincl. V12 Vantage
Aston Martin/Ford Confidential
Component/ System Fault Code Monitor Strategy
Description Malfunction Criteria Threshold Parameter Secondary Parameters Entry Parameters Time Required DTC
StorageMIL Illumin-
ation
Engine coolant temp 110 deg C (> 230 deg F)Continuous time with
engine off prior to start > 360 min
Time with high sensor
signal > 100 sec
ECT at start differs from
IAT at start >28 deg C
(> 50 deg F)
Catalyst, Misfire, Fuel
System or HO2S Monitors
Sensor signal voltage > 4.9 volts (-41.25degF)
Fault filter routine > 5.0 sec
Sensor signal voltage < 0.13 volts (302.75degF)
Fault filter routine > 5.0 sec Engine off soak time >360 minutes
IAT sensor OK
(P0112/0113)
Rationality check, Engine-Off
timer inoperative Soak timer value at startup < 0.5 * 60 sec (Timer
indicates that short
soak has occurred)Engine coolant
temperature at previous
key-off >90degC (indicates hot
engine)
Engine coolant
temperature at previous
key-off - coolant at start > 55 deg C
(> 100 deg F)
(Degree of cooling
indicates that a long soak
has occurred)
Vehicle ID block not
programmed P1639 VID block not programmed
with tire/axle ratio Time with error present > 0 sec
NoneNoneContinuous Footnote a) Footnote c)
VID Block checksum P0602 VID block checksum test failedTime with error present > 0 sec
NoneNoneContinuous
KAM Failed / reset P0603 Keep Alive Memory check failed / memory was resetTime with error present > 0 sec
NoneNoneContinuous Footnote a) Footnote c)
RAM memory failed P0604 Random Access Memory test has failed.Time with error present > 0 sec
NoneNoneContinuous Footnote a) Footnote c)
ROM checksum test
failed P0605 Read Only Memory test failed Time with error present > 0 sec
NoneNoneContinuous Footnote a) Footnote c)
CPU Fault detected P0607 General fault with the CPU has been detectedTime with error present > 0 sec
NoneNoneContinuous
Keep Alive Memory
Power Input P1633 KAM power input voltage too
low/open circuit Time with error present > 20 sec
NoneNoneContinuous Footnote k) Footnote i)
Loss of
Communication with
TCM U0101 Monitors CAN bus between
ECM and TCM Time with fault present > 1.36 seconds
Continuous
Sensor input < 0.21 volts (131degC)
or
> 4.93 volts(-45degC)
Time with sensor input out
of range > 3.0 sec
Sensor input < 0.21 volts (131degC)
Time with sensor input out
of range > 3.0 sec
Sensor input > 4.93 volts
(-45degC)
Time with sensor input out
of range > 3.0 sec 11< Voltage <18 Continuous Footnote a) Footnote c)
MATF Sensor Input P0097 (High) Range check Battery Voltage
P0098 (Low) Range check
P009A Rationality Check - error between manifold temperature
and IAT after long soak Manifold temperature -
IAT
>< +/- 26degC
(80degF)
ECT Sensor Input P0116 Rationality check (Stuck high)
Once per driving
cycleFootnote a) Footnote c)
Engine-Off (Soak)
Timer Rationality
Test P0606
Once per driving
cycleFootnote a) Footnote b)
Fuel Temperature
Sensor Input P0180
P0182 (Low)
P0183 (High)Circuit Malfunction - range
check
Circuit Malfunction - range
check
None
N/A Continuous Footnote a) Footnote c)
11