2010 ACURA ZDX Owners Manual

The radar sensor may not always
scan as intended. Here are two
examples:●Your vehicle is tilted because of a
heavy load in the rear or from
modifications to the suspension.
Do not overload your vehicle (see
Carrying Cargoon page 465), and
do not make any modifications to
the suspension (see Accessories
and Modifications on page 463).●The tires are not correctly
maintained. Always make sure the
tire pressures are correct (see
page 568), and that the tires are
the correct size and in good
condition (see Tires on page 567). Collision Alarm
If the system senses a likely collision
with a vehicle or object ahead of you,
it alerts you with an audible and a
visual alarm.
The audible alarm is a constant
beeping sound; the visual alert is an
amber colored BRAKE message that
flashes on the multi-information
display. If these alarms come on,
take the appropriate means to
prevent a collision (apply the brakes,
change lanes, etc.).
Collision Mitigation Braking System
™(CMBS™ )50009/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

Distance between vehicles
CMBS
The radar sensor detects a vehicle E-pretensionerAudio & Visual
WARNINGS Braking
operation
Stage one There is a risk of a
collision with the
vehicle ahead, or the
distance between the
vehicles has dropped
below a certain level.
—
A beep sounds
and
‘‘BRAKE ’’
flashes on the
multi-
information
display.
—
Stage two The distance between
the two vehicles
continues to diminish.Retracts the driver's
seat belt gently a few
times, providing a
physical warning.
Lightly
applied
Stage three
ꭧ
The CMBS determines
that a collision is
unavoidable. Forcefully tightens
driver and front
passenger seat belts.
Forcefullyapplied
ꭧ : Depending on the circumstances, CMBS may not go through all of the alert stages before initiating the last stage.
YOUR
VEHICLE VEHICLE
AHEAD
YOUR
VEHICLEVEHICLE
AHEAD
YOUR
VEHICLEVEHICLE
AHEAD
CONTINUED
Collision Mitigation Braking System
™(CMBS™ )
501
Driving
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

CMBS OFF ButtonTo turn the CMBS off, press the
CMBS OFF button under the driver's
side vent for about 1 second. When
you do this, a beeper sounds, a
CMBS indicator on the instrument
panel comes on, and a CMBS OFF
message appears on the multi-
information display. To turn the
system back on, press the button
again for about 1 second.When you select the ON mode by
operating the engine start/stop
button (see page 194), the CMBS is
turned on if it was on previously.
Automatic Shut Off
Any of the conditions below can
cause the CMBS to shut off. When
the system shuts off, the CMBS
indicator in the instrument panel
comes on, and a CHECK CMBS
SYSTEM message appears on the
multi-information display for about 5
seconds.
●An abnormal tire condition is
detected (wrong tire size, flat tire,
etc.).●Extended off-road or mountainous
driving.●Driving your vehicle with the
parking brake applied.●Driving your vehicle in bad
weather (rain, fog, snow, etc.).●A dirty radar sensor cover on the
front grille.
The CMBS will automatically recover
when these conditions are improved.
CMBS OFF BUTTON
Collision Mitigation Braking System ™(CMBS™ )50209/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

CMBS IndicatorThis indicator comes on for several
seconds when you select the ON
mode by operating the engine start/
stop button (see page 194). It also
comes on and stays on when you
turn the CMBS off by pressing the
CMBS OFF button.
To turn the CMBS back on, make
sure the vehicle is stopped and the
power mode is set to ON, then press
the CMBS OFF switch for about 1
second.The CMBS indicator normally comes
on under these conditions:
●When you manually turn off the
system.●When the system shuts off
automatically.●When you drive in bad weather
(rain, snow, fog, etc.).●If anything covers the radar sensor
cover (dirt, mud, dry leaves, wet
snow, etc.).●When the VSA system indicator
comes on (see page 508).
●When you select the ON mode by
operating the engine start/stop
button, the CMBS indicator should
come on for a few seconds, then
go off. If the indicator comes on at
any other time and a CHECK
CMBS SYSTEM message appears
on the multi-information display,
there is a problem with the CMBS.
You can still drive your vehicle,
but CMBS will not be operating.
Have your vehicle checked by a
dealer.
CMBS
INDICATOR
U.S. model is shown.
CONTINUED
Collision Mitigation Braking System ™(CMBS™ )
503
Driving
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

Limitations
The CMBS may not activate under
some conditions. Here are a few
examples:●The distance between your vehicle
and the vehicle ahead of you is too
short.●A vehicle cuts in front of you at a
slow speed.
●A vehicle cuts in front of you and
brakes suddenly.●When you accelerate rapidly and
approach the vehicle ahead of you
at high speed.●Immediately after you drive off.
●Driving in heavy, stop-and-go
traffic.●The vehicle ahead of you is a
motorcycle or other small vehicle.
YOUR VEHICLE
YOUR VEHICLE
Collision Mitigation Braking System™(CMBS™ )50409/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

●A vehicle suddenly crosses in front
of you.
The CMBS is not designed to detect
pedestrians.
Even with little or no chance of a
collision, the CMBS may activate
under these conditions:●When you change lanes quickly,
then overtake the vehicle ahead of
you.
●When you approach or pass a
vehicle ahead of you that is turning
left or right in an intersection.
YOUR VEHICLE
YOUR VEHICLE
CONTINUED
Collision Mitigation Braking System™(CMBS™ )
505
Driving
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

●When you pass a low bridge at
high speed.●When you go over a sharp-edged
speed bump at high speed.●When you go over areas of
construction on the road surface.
●When you approach train tracks at
the bottom of a hill and you do not
apply the brakes.
Because of the road condition
(curved, winding, etc.) or the state of
your vehicle (turning angle, lane
position, etc.), CMBS can sometimes
mistake a stationary object (light
pole, traffic sign, etc.) as a vehicle
ahead of you and temporarily
operate. This is normal.
LOW BRIDGE
RAILS
YOUR VEHICLE
SIGN, POLE, etc.
Collision Mitigation Braking System ™(CMBS™ )50609/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

Important Safety Reminder
The main purpose of the CMBS is to
reduce the severity of injuries caused
by an unavoidable collision. While
the CMBS may help to alert you and
minimize the severity of a collision, it
may not activate in every dangerous
situation.
Even with the CMBS, it is still your
responsibility to operate the brake
pedal and steering wheel
appropriately, according to the
driving conditions.
As required by the FCC:This device complies with Part 15 ofthe FCC rules. Operation is subjectto the following two conditions: (1)
This device may not cause harmfulinterference, and (2) this device mustaccept any interference received,including interference that maycause undesired operation.
Changes or modifications notexpressly approved by the partyresponsible for compliance could
void the user's authority to operatethe equipment.
This device complies with IndustryCanada Standard RSS-210. Operationis subject to the following twoconditions: (1) this device may notcause interference, and (2) thisdevice must accept any interference
that may cause undesired operationof the device.
Collision Mitigation Braking System ™(CMBS™ )
507
Driving
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com