2010.5 Peugeot 407 C Owner's Manual

3
49
In order to ensure optimum vis-
ibility during your manoeuvres,
the mirror lightens automati-
cally when reverse gear is en-
gaged.
By means of a sensor, which mea-
sures the light from the rear of the ve-
hicle, this system automatically and
progressively changes between the
day and night uses.
It has an anti-dazzle system which
darkens the mirror glass: this reduces
any driver discomfort caused by the
light beams of following vehicles, the
sun...
Automatic day/night model
Rear view mirror
Adjustable mirror providing a central
rearward view.
Equipped with an anti-dazzle system,
useful in poor light.

3
50
ELECTRIC ADJUSTMENT OF STEERING WHEEL HEIGHT AND REACH
When stationary, adjust the height or
reach of the steering wheel by moving
the control:

 forwards or backwards to adjust
the reach.

 up or down to adjust the height.
You can activate or deac-
tivate this function via the
"personalisation - confi gu-
ration" menu in the multi-
function screen.
WELCOME FUNCTION
When the driver's door is opened with
the ignition off, the steering wheel rises
to make access to or exit from the ve-
hicle easier. MANUAL ADJUSTMENT OF STEERING WHEEL HEIGHT AND REACH
When the vehicle is stationary, un-
lock the steering wheel adjustment by
pushing the lever forwards.
Adjust the height and reach of the
steering wheel then lock the adjust-
ment by pulling the lever fully back.
Reinitialisation
Following reconnection of the battery,
the welcome function must be reini-
tialised:
- move the control in the direction of the required adjustment,
- release the control,
- move the control again until it reaches its stop.
This procedure must be carried out for
all four directions.

3
51
MANUAL FRONT SEATS
Longitudinal adjustment
Lift the control bar and slide the seat
forwards or backwards. Driver and passenger seat cushion
height and angle adjustment
Pump up or down to the required position.
Seat back angle adjustment
Without resting your back against the
seat, turn the control to adjust the
angle of the seat back.

3
53
Heated seat adjustment
With the engine running, turn the knob.
The temperature of the seat is regu-
lated automatically.

0: Off.

1: Low.
2: Medium.

3: High.
Driver and passenger seat lumbar
adjustment *
Operate the lever to obtain the re-
quired position.
Access to the rear seats
If necessary, detach the seat belt from
the handle and position it along the
door pillar.
Pull the handle
A upwards and for-
wards to fold the seat back, then move
the seat forward pushing the seat
back.
The driver has a courtesy handle B
to enable him to move the passenger
seat from his seat.
When it is put back in place, the seat
returns to its initial position. No person or object must pre-
vent the seat from returning
to its initial
longitudinal and

angle position.
Depending on your seat's set-
tings, it is possible that the access
to the rear seats manoeuvre may be
limited. In this case, the seat settings
must be altered fi rst.
The seat must return to this position
for correct locking of the seat back.
Ensure that the seat back returns to
its position correctly and never drive
with the seat back disengaged (able to
move freely).
If the seat back jams on repositioning,
operate the handle A again to release
it and return it to its initial position.
* With electric seat only.
Do not use the seat back an-
gle adjustment control when
using the access to the rear
seats (risk of disengaging of
the seat back with loss of the angle
adjustment function).

3
54
Head restraint height and angle
adjustment
To raise or lower the head restraint,
pull it forwards then slide it.
To tilt the head restraint, tilt the lower
part forwards or backwards.
To remove the head restraint, move it
almost to the highest position, lift the
tab using a coin and pull the head re-
straint forwards and upwards at the
same time.
To refi t the head restraint, engage the
stalks in the holes keeping in line with
the seat back. Front seat active head restraint
This system prevents whiplash.
In the event of a rear impact, the action
of the body on the seat back moves
the head restraint forwards and up-
wards preventing the head from being
thrown backwards.
Front armrest
To change the position of the armrest:

 Lift the lever 1 .
The adjustment is correct
when the top of the head re-
straint is level with the top of
the head. Never drive with the head
restraints removed; they must
be in place and adjusted
correctly. The armrest folds forwards and up-
wards.
To return to the initial position, push
the armrest backwards and press it to
engage.

3
52
ELECTRIC FRONT SEATS
Longitudinal adjustment
Push the control forwards or back-
wards to slide the seat. Driver and passenger seat cushion
height and angle adjustment

Height : tilt the rear of the control up
or down.

Angle : tilt the front of the control up
or down. Seat back angle adjustment
Tilt the control forwards or backwards
to adjust the angle of the seat back.
The electrical functions of the
driver's seat (with the exception
of the access to the rear seats)
are deactivated approximately
one minute after the ignition is switched
off.
To reactivate them, open the door or
switch on the ignition.

3
53
Heated seat adjustment
With the engine running, turn the knob.
The temperature of the seat is regu-
lated automatically.

0: Off.

1: Low.
2: Medium.

3: High.
Driver and passenger seat lumbar
adjustment *
Operate the lever to obtain the re-
quired position.
Access to the rear seats
If necessary, detach the seat belt from
the handle and position it along the
door pillar.
Pull the handle
A upwards and for-
wards to fold the seat back, then move
the seat forward pushing the seat
back.
The driver has a courtesy handle B
to enable him to move the passenger
seat from his seat.
When it is put back in place, the seat
returns to its initial position. No person or object must pre-
vent the seat from returning
to its initial
longitudinal and

angle position.
Depending on your seat's set-
tings, it is possible that the access
to the rear seats manoeuvre may be
limited. In this case, the seat settings
must be altered fi rst.
The seat must return to this position
for correct locking of the seat back.
Ensure that the seat back returns to
its position correctly and never drive
with the seat back disengaged (able to
move freely).
If the seat back jams on repositioning,
operate the handle A again to release
it and return it to its initial position.
* With electric seat only.
Do not use the seat back an-
gle adjustment control when
using the access to the rear
seats (risk of disengaging of
the seat back with loss of the angle
adjustment function).

3
54
Head restraint height and angle
adjustment
To raise or lower the head restraint,
pull it forwards then slide it.
To tilt the head restraint, tilt the lower
part forwards or backwards.
To remove the head restraint, move it
almost to the highest position, lift the
tab using a coin and pull the head re-
straint forwards and upwards at the
same time.
To refi t the head restraint, engage the
stalks in the holes keeping in line with
the seat back. Front seat active head restraint
This system prevents whiplash.
In the event of a rear impact, the action
of the body on the seat back moves
the head restraint forwards and up-
wards preventing the head from being
thrown backwards.
Front armrest
To change the position of the armrest:

 Lift the lever 1 .
The adjustment is correct
when the top of the head re-
straint is level with the top of
the head. Never drive with the head
restraints removed; they must
be in place and adjusted
correctly. The armrest folds forwards and up-
wards.
To return to the initial position, push
the armrest backwards and press it to
engage.