2010.5 Peugeot 407 C Owner's Manual

1010
115
CHANGING A FUSE
The fuseboxes are placed in the glove
box (passenger side), in the engine
compartment (left-hand side) and in
the left boot trim.
Dashboard fuses
To access the fuses, open the glove
box and tilt the fusebox lid.
Replacing a fuse
Before replacing a fuse, the cause of
the fault must be found and rectifi ed.
The fuse numbers are indicated on the
fusebox. Always replace a faulty fuse
with a fuse of the same rating
(same colour). Use the special tweezer located on
the support next to the fusebox; this
support also contains the replacement
fuses.

Fuse N°
Rating

A
Functions

G29 - Not used.

G30 5 Heated rear screen.

G31 5 Tyre under-infl ation detection.

G32 - Not used.

G33 5 Power steering electropump unit,
dual-function brake switch.

G34 5 Dual-function brake switch,
automatic gearbox relay.

G35 5
Steering wheel angle sensor and ESP gyroscope senso r.

G36 25 Hi-Fi amplifi er.

G37 15 Automatic gearbox.

G38 20 Heated seats.

G39 30 Passenger seat memory unit.

G40 30 Driver’s seat memory unit.

1010
115
CHANGING A FUSE
The fuseboxes are placed in the glove
box (passenger side), in the engine
compartment (left-hand side) and in
the left boot trim.
Dashboard fuses
To access the fuses, open the glove
box and tilt the fusebox lid.
Replacing a fuse
Before replacing a fuse, the cause of
the fault must be found and rectifi ed.
The fuse numbers are indicated on the
fusebox. Always replace a faulty fuse
with a fuse of the same rating
(same colour). Use the special tweezer located on
the support next to the fusebox; this
support also contains the replacement
fuses.

Fuse N°
Rating

A
Functions

G29 - Not used.

G30 5 Heated rear screen.

G31 5 Tyre under-infl ation detection.

G32 - Not used.

G33 5 Power steering electropump unit,
dual-function brake switch.

G34 5 Dual-function brake switch,
automatic gearbox relay.

G35 5
Steering wheel angle sensor and ESP gyroscope senso r.

G36 25 Hi-Fi amplifi er.

G37 15 Automatic gearbox.

G38 20 Heated seats.

G39 30 Passenger seat memory unit.

G40 30 Driver’s seat memory unit.

1010
116

Fuse N°
Rating

A
Functions

F1 - Not used.

F2 30 Locking and deadlocking.

F3 5 Airbags and pretensioners control unit.

F4 10 Automatic gearbox switch, diagnostic socket, electrochromatic mirror.

F5 30 Driver and passenger electric windows.

F6 30 Sunroof.

F7 5 Glove box lamp, map reading lamps, courtesy lamps, courtesy mirrors.

F8 20 Multifunction screen, audio equipment, top-of-column, trailer
fusebox (accessory),
alarm, alarm siren.

F9 30 Front cigar lighter, 12 V rear socket, glove box lamp, map readi
ng lamps, courtesy lamps,
courtesy mirrors.

F10 15 Tyre under-infl ation detection, CD changer.

F11 15 Diagnostic socket, ignition switch.

F12 15 Trailer fusebox (accessory), parking sensors control unit supply,
passenger seat memory unit, rain and sunshine sensor.

F13 5 Windscreen wipers relay control, engine fusebox.

F14 15 Driver’s seat memory unit, instrument panel, airbags and pre-tensi
oners control unit,
air conditioning control panel, steering wheel adjustment sw itch, hands-free kit.

F15 30 Locking and deadlocking.

F16 - PARC shunt.

1010
117
Engine compartment fuses
To access the fuses located in the
engine compartment (next to the bat-
tery), remove the battery cover and
unclip the fusebox cover.
Close the fusebox cover carefully and
refi t the battery cover when you have
fi nished.
Fuse N°
Rating

A
Functions

1 20 Engine control unit, fan assembly relay supply.

2 15 Horn.

3 10 Screenwash pump.

4 20 Headlamp wash pump.

5 15 Fuel pump, engine management actuators
(air fl ow sensor, electrovalves, ...).

6 10 ESP control unit.

7 10 Automatic headlamp adjustment.

8 20 Starter coil.

9 10 Directional headlamps control unit, additional
heating switching and protection control unit,
clutch switch.

10 30 Engine management actuators (ignition coil,
injectors, thermostats, electrovalves, oxygen
sensors), Diesel additive pump, fuel pump,
engine control unit, blow-by heater.

11 40 Air conditioning fan.

12 30 Windscreen wipers.

13 40 Built-in systems interface supply
(ignition positive).

14 30 Not used.

1010
118
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer. PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installation
of accessories not supplied and not
recommended by PEUGEOT and not
installed in accordance with its instruc-
tions, in particular where the equip-
ment in question consumes more than
10 milliamperes. The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer.

1010
119
CHANGING A WINDSCREEN WIPER BLADE
ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
LOAD REDUCTION FUNCTION
When driving, certain functions (air
conditioning, heated rear screen,
heating system for passenger com-
partment of Diesel vehicles, etc.) may
be switched off temporarily, depending
on the level of battery charge.
Reactivation of these functions is au-
tomatic, once the battery charge is
suffi cient.
Note: at the risk of discharg-
ing the battery, the functions
that have been switched off
may be reactivated manually.

Note : if the telephone is being
used when economy mode
starts, it will still be possible to
fi nish the call.
A fl at battery prevents the en-
gine from starting.
Replacing a blade

 Lift the arm, then unclip the blade
and remove it.

 Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. Once the hour is over, a switching to
economy mode message appears in
the multifunction scren and the active
functions are put on standby.
These functions are reactivated au-
tomatically next time the vehicle is
driven.
In order to resume the use of these
functions immediately, the engine
must be started and left to run for a
few minutes.
The time available to you will then be
approximately double the duration
for which the engine is left running.
However, this period will always be
between fi ve and thirty minutes.
This time may be signifi cantly
reduced if the battery charge
is low.
Placing the wiper blades in the
maintenance position

 Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades vertically on the windscreen
(maintenance position).

1010
120
Disconnecting/Reconnecting
the cables

1. Raise the locking plate A .

2. Position the open clip of the cable
on the positive (+) terminal of the
battery.

3. Press until the position checking
system B tilts.

4. Lock the clip by lowering the lock-
ing plate while pressing on the clip. To start the vehicle from another
battery:
-
Connect the red cable to the positive (+)
terminals of the two batteries,
- Connect one end of the green or
black cable to the negative (-) ter-
minal of the slave battery,
- Connect the other end of the green or black cable to an earth point on
the broken down vehicle as far as
possible from the battery,
-
Operate the starter, let the engine run,
- Wait for the engine to return to idle, then disconnect the cables.
ENGINE COMPARTMENT)
To charge the battery using a
battery charger:
- Disconnect the battery,
-
Follow the instructions for use given by
the manufacturer the battery charger,
- Reconnect starting with the nega-tive (-) terminal,
- Check that the terminals and connec- tors are clean. If they are covered with
sulphate (white or greenish deposit),
disconnect them and clean them.
It is advisable to disconnect
the battery if the vehicle is not
to be used for a period of more
than one month.
Do not force the plate as locking
is not possible if the clip is not
positioned correctly.
Start the procedure again.

1010
Before disconnecting the bat-
tery, you must wait for 2 minu tes
after switching off the ignition.
Never disconnect a terminal
when the engine is running.
Never charge a battery without fi rst
disconnecting the terminals.
Open the windows and close the sun-
roof before disconnecting the battery.
If they do not operate normally follow-
ing reconnection of the battery, they
must be reinitialised (see paragraphs
"Reinitialisation of the electric windows"
and "Sunroof").
After every reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to allow the
electronic systems to be initialised.
However, if slight diffi culties are ex-
perienced after this, please contact a
PEUGEOT dealer.

On the 2.7 litre 24V HDI engine, if
there is no battery in the boot, do
not connect a slave battery to the
positive (+) and negative (-) termi-
nals under the bonnet as a short
circuit may occur.
The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance
with regulations and must never be
discarded with household waste.
Take used batteries to an approved
collection point.

 open the bonnet,

 use the two additional positive (+)
and negative (-) terminals located
under the bonnet,

 open the red cover of the positive (+)
terminal,


connect the red cable between the
positive (+) terminal and the positive (+)
terminal of the slave battery,

 connect the green or black cable
between the negative (-) terminal
and the negative (-) terminal of the
slave battery,


operate the starter, let the engine run,

 wait for the engine to return to idle,
then disconnect the cables,


close the red cover of the positive (+)
terminal,

 refi t the left side cover,

 close the bonnet.
IN THE BOOT) *
* Vehicles fi tted with the 3 litre HDI V6
24V engine.
The battery is behind the left hand
boot trim.

To charge the battery using a battery
charger (boot open):

 fold down the panel to gain access
to the battery,

 disconnect the battery,

 follow the instructions for use given
by the battery charger manufacturer,

 reconnect starting with the nega-
tive (-) terminal,

 raise the panel and close it.
To start the vehicle from another
battery: