2010.5 Peugeot 407 C Owner's Manual

1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer's servicing schedule.
Once an engine oil level indication has been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
ner fl ash.

Example : when the ignition is switched on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains on.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last
service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user's driving conditions.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is on.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

Example : when switching on the ig-
nition and for 5 seconds, the display
shows that 400 miles/900 km remain
before the next service is due.

1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer's servicing schedule.
Once an engine oil level indication has been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
ner fl ash.

Example : when the ignition is switched on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains on.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last
service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user's driving conditions.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is on.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

Example : when switching on the ig-
nition and for 5 seconds, the display
shows that 400 miles/900 km remain
before the next service is due.

1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder re-
set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil fi ller cap,
using the type of oil suited
to your engine.

A = max.

B = min.
Oil level correct
Oil level too low
Flashing indicates that the oil level is
too low, which may damage the en-
gine.
If the low oil level is confi rmed by
checking with the dipstick, the level
must be topped up. Oil level indicator fault
(fl ashing segments)
Check the oil level using the dipstick.
If the level is correct, the fl ashing indi-
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi ve minutes, otherwise the zero
re-set will not be registered.

1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder re-
set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil fi ller cap,
using the type of oil suited
to your engine.

A = max.

B = min.
Oil level correct
Oil level too low
Flashing indicates that the oil level is
too low, which may damage the en-
gine.
If the low oil level is confi rmed by
checking with the dipstick, the level
must be topped up. Oil level indicator fault
(fl ashing segments)
Check the oil level using the dipstick.
If the level is correct, the fl ashing indi-
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi ve minutes, otherwise the zero
re-set will not be registered.

1
30
Trip recorder zero reset
With the trip mileage displayed, press
the button for a few seconds.
Mileage recorder
The total mileage is displayed in
zone A of the screen and the trip mile-
age in zone B .
LIGHTING DIMMER
With the exterior lighting on, press the
button to vary the intensity of the light-
ing of the instruments and controls.
When the lighting reaches the mini-
mum (or maximum) setting, release
the button then press it again to in-
crease (or reduce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.

1
31
TRIP COMPUTER

or
TRIP: access to the trip
computer information.
Zero reset
When the required trip is displayed,
press the control for more than
two seconds. - trip
"1" tab with:

1
32
Press the "MENU" button to open the
main menu.
Select the "Trip computer" or

"Vehicle diagnostics" application
using the navigator, then confi rm or
press the "MODE" button until you
reach the trip computer screen, then
confi rm using "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Warnings log,
- Status of the functions,
- Input of the distance to be travelled.
Alert log
This summarises the active warning
messages, displaying them in the mul-
tifunction screen in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled value.
Display in the instrument panel screen
All of the various items of trip computer
information also appear on the instru-
ment panel screen at the same time.
Distance remaining to be travelled (miles or km)
Average speed (mph or km/h)
Average fuel consumption (mpg or l/100 or km/l)
Distance travelled (miles or km)
This is the average speed calculated
since the computer was last reset to
zero (with the ignition on).
This is the distance remaining to the
destination, either calculated at any
time by the navigation if guidance is
activated, or entered by the user, mi-
nus the distance covered since the
distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last reset to
zero.
This indicates the distance travelled
since the computer was last reset to
zero.
"TRIP" menu

2
33
COLOUR SCREEN C
This displays the following informa-
tion, via the Peugeot Connect Sound
control panel:
- time,
- date,
- ambient temperature (the value displayed fl ashes if there is a risk
of ice),
- openings check,
- warning messages,
- audio functions,
- trip computer information,
- personalisation and confi guration displays,
- air conditioning settings,
- front and rear parking sensors dis- play,
- hands-free kit information. Management of the displays
For example: "TRIP"
Main menu
Press the
"MENU" button to gain ac-
cess to the main menu and select
one of the following functions:
- "Audio functions",
- "Trip computer",
- "Personalisation-Confi guration",
- "Air conditioning",
- "Telephone". "Personalisation-Confi guration"
menu
This provides access to successive
confi rmation windows.
Defi ne the vehicle parameters
This enables you to activate or deac-
tivate certain driving and comfort sys-
tems:
- "Automatic lighting of headlamps",
- "Guide-me-home lighting" and
"Duration",
- "Remote control action",
- "Permanent locking of the boot",
- "Directional headlamps".
The
"AUDIO" , "TRIP" , "CLIM" and

"TEL" buttons on the audio system
control panel allow display in the main
window.
For example: "Audio functions" For example: "Automatic lighting of
headlamps"